Intermec EasyCoder 3400e Manuale utente
3400, 4420, and 4440 Cutter
P/N 066391-001
User’s Manual
Intermec Technologies Corporation
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
U.S. service and technical support: 1-800-755-5505
U.S. media supplies ordering information: 1-800-227-9947
Canadian service and technical support: 1-800-688-7043
Canadian media supplies ordering information: 1-800-268-6936
Outside U.S. and Canada: Contact your local Intermec service supplier.
The information contained herein is proprietary and is provided solely for the purpose of allowing
customers to operate and/or service Intermec manufactured equipment and is not to be released,
reproduced, or used for any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change without notice.
1998 by Intermec Technologies Corporation
All Rights Reserved
The word Intermec, the Intermec logo, JANUS, IRL, TRAKKER, Antares, Adara, Duratherm,
EZBuilder, Precision Print, PrintSet, Virtual Wedge, and CrossBar are either trademarks or
registered trademarks of Intermec Technologies Corporation. Throughout this manual, trademarked
names may be used. Rather than put a trademark (or ) symbol in every occurrence of a
trademarked name, we state that we are using the names only in an editorial fashion, and to the
benefit of the trademark owner, with no intention of infringement.
Introduction to the Cutter
3
This manual explains how to install and clean the cutter on your 3400, 4420, or 4440
printer. It also explains how to enable the cutter using PrintSet.
Introduction to the Cutter
With the cutter on your 3400, 4420, or 4440 printer, you can cut media into
individual labels of the same or random lengths that are ready for use. The
cutter blade is capable of cutting a wide range of die cut roll, continuous roll, or
fanfold media; however, the cutter performs best with 7- to 10-mil thickness tag
stock.
The cutter is mounted externally on the printer and cannot be used in
conjunction with the self-strip/batch takeup option.
Note: If you use the cutter on adhesive backed materials, cut the liner between the
labels. Cutting through adhesive is not recommended. You will need to clean the cutter
every 10,000 cuts or when it fails to cut cleanly if you cut through adhesive backed
material.
Cutter Parts and Function
The following table describes the parts and function of the cutter and how they
connect to the printer.
Name Description
Mounting plate Attaches the cutter to the printer. The mountin
g
plate has a
sprin
g
mounted hin
g
e that allows the cutter to swin
g
down so
that media can be fed easily through the cutter.
Cutter cable Powers and sends commands from the main PCB to the cutter.
Cutter connector Connects the cutter cable to the main PCB.
Cutter cover Prevents fin
g
ers from comin
g
into contact with the cutter blade.
It opens easily for cleaning.
Cutter blade Cuts the media when the printer reaches the end of the label.
Thumbscrews Attach the mountin
g
plate to the cutter and the cutter to the
mounting plate.
3400, 4420, and 4440 Cutter User’s Manual
4
Attaching the Cutter
1. Turn off the printer.
2. Unplug the printer power supply cord.
3. Remove the media cover.
A. Pull the bottom of the media cover away from the base of the printer.
B. Lift the front of the media cover upward to release it from the printer
frame.
C. Lift the media cover away from the top of the printer.
44XXU.001
Feed/Pause
Power/Data
Alert
Empty/Pause
IntermecIntermec
4420
4. Turn the head lift lever clockwise and pull the media back to the printhead.
5. Push down on the mounting plate below the hinge and hold it down with
the cutter pressed against the mounting plate.
6. Using the thumbscrews on the mounting plate, attach the cutter to the
mounting plate. Make sure the cutter cable goes through the notch in the
mounting plate.
Attaching the Cutter
5
Attaching the Cutter to the Mounting Plate
Feed/Pause
Power/Data
Alert
Empty/Pause
Intermec
4420
44XXU.002
Front of
cutter
Cutter
connector
Cutter
cable
Front of
cutter
Mounting
plate
Thumbscrew
Head lift
lever
Cable
notch
Thumbscrew
7. Plug the cutter cable into the cutter connector at the base of the inside wall
of the printer.
44XXU.003
Cutter
connector
Cutter
cable
3400, 4420, and 4440 Cutter User’s Manual
6
8. Feed the media through the cutter. The media should extend out past the
opening in the cutter cover.
Feed/Pause
Power/Data
Alert
Empty/Pause
IntermecIntermec
4420
Cutter
cover
44XXU.004
9. Turn the head lift lever counterclockwise to secure the printhead.
10. Replace the media cover.
11. Plug in the printer power supply cord.
12. Turn on the printer.
Enabling the Cutter
7
Enabling the Cutter
The following instructions use PrintSet to enable the cutter, but you can also
use the IPL to enable the cutter. For help, see the IPL Programming Reference
Manual.
1. Start PrintSet on your PC.
Note: Under the Printer Select menu, check that PrintSet is set up for your printer
configuration (3400, 4420, or 4440). To customize the configuration for your
printer, see the Help menu.
2. Click the Paper Handling button.
3400, 4420, and 4440 Cutter User’s Manual
8
3. From the Paper Handling dialog box, select Cutter.
4. Choose OK.
Note: If you want to change other configuration settings, you should do so before
going to Step 5. For help changing the configuration, see the Help menu.
5. Choose the Send Command button.
A message box appears asking if you want to overwrite the current printer
settings. Choose send to enable the cutter with either the default printer
configuration or the configuration you have created.
6. Exit PrintSet.
Note: To disable the cutter, use this procedure but deselect Cutter at Step 3.
Cleaning the Cutter
9
Cleaning the Cutter
It is important that you routinely clean the cutter to keep it in excellent working
condition. If you are cutting through adhesive-backed media, you should clean
the cutter after every 10,000 cuts. To see the number of cuts made, print out a
hardware configuration test label as described in your printer user’s manual.
The information following “Labels Cut” indicates how many labels have been
cut since the cutter was installed. Use this number to determine when to clean
the cutter.
If you are not using adhesive-backed media, you should clean the cutter when
it no longer cuts precisely.
Warning
Use extreme caution when cleaning the cutter to avoid cutting yourself.
Avertissement
Lors du nettoyage de la barre coupante, prenez bien soin de ne pas vous
couper.
To clean the cutter blade and paper guide
1. Turn off the printer.
2. Unplug the printer power supply cord and the cutter cable.
3. Turn the head lift lever clockwise and back the media out of the cutter.
4. Using a straight-slot screwdriver, loosen the screw on the top of the cutter
and swing the cutter cover down.
Feed/Pause
Power/Data
Alert
Empty/Pause
IntermecIntermec
4420
Cutter
cover
44XXU.005
3400, 4420, and 4440 Cutter User’s Manual
10
5. Push down on the tab so that the cutter blade swings forward.
Feed/Pause
Power/Data
Alert
Empty/Pause
IntermecIntermec
4420
44XXU.006
Tab
Cutter
blade
6. With a cotton swab moistened with alcohol, clean the blade.
Note: Do not clean or get alcohol on the lubricated portions of the cutter.
7. Swing the blade up.
8. Remove any dust or media debris from inside the cutter.
Altri manuali per EasyCoder 3400e
7
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Intermec Accessori per stampanti
Intermec
Intermec EasyCoder PF2i Manuale utente
Intermec
Intermec EasyCoder PF2i Manuale utente
Intermec
Intermec PB42 Manuale utente
Intermec
Intermec PB42 Manuale
Intermec
Intermec 3600 Manuale utente
Intermec
Intermec UBI EasyCoder 601 E Guida
Intermec
Intermec EasyCoder 3400e Manuale utente
Intermec
Intermec EasyCoder 4420 Manuale
Intermec
Intermec PA30 Manuale utente
Intermec
Intermec PW50 Manuale utente
Intermec
Intermec EasyCoder PF8 Manuale utente
Intermec
Intermec EasyCoder 601XP Manuale utente
Intermec
Intermec EasyCoder PF4ci Manuale utente
Intermec
Intermec EasyCoder 4420 Manuale utente
Intermec
Intermec PW50 Manuale utente
Intermec
Intermec 3400 Manuale utente
Intermec
Intermec EasyCoder 501 SA Manuale utente
Intermec
Intermec EasyCoder 601XP Manuale utente
Intermec
Intermec EasyCoder 501 SA Manuale utente
Intermec
Intermec EasyCoder PF2i Manuale utente
