Josef Kihlberg a.560PN Manuale utente
2© Josef Kihlberg AB 2007
EN
Table of Contents
Installation ........................................................................... 3
Tool use ............................................................................4-5
Safety precautions............................................................6-7
Troubleshooting and maintenance ...................................... 8
Technical specification......................................................... 9
Spare parts drawing ..................................................... 10-11
Spare parts kits, accessories............................................. 12
Applications ....................................................................... 13
Warranty terms, serial numbers ........................................ 14
CE Conformity Declaration................................................ 15
3© Josef Kihlberg AB 2007
EN
Installation
Adjust to the lowest air pressure that will bend the staples
correctly. Start at about 5.0 bar and increase the pressure by
0.5 bar increments until the pressure is correct.
Never exceed 8 bar.
Low air pressure helps to keep down maintenance costs.
Make sure that the minimum internal diameter of the air
hose is 6 mm (1/4") and that of the nipple is a minimum of
5 mm (6/32"). This will prevent incorrect operation due to a
significant drop in pressure. The tool and the hose must be
fitted with a connection nipple that automatically bleeds the
tool when it is disconnected.
4© Josef Kihlberg AB 2007
EN
Adjust to the lowest air pressure that will bend the staples
correctly. Start at about 5.0 bar and increase the pressure
by 0.5 bar increments until the pressure is correct.
Never exceed 8 bar.
Low air pressure helps to keep down maintenance costs.
The tool is adjustable for 15 or 18 mm staples. The tool
setting for a different staple leg length is altered as follows.
Start by adjusting the depth of stapling for deep clinching
(=) as shown in the upper picture.
Then in order to adjust to required leg length.
1. Slacken the locking screw (A) underneath with a 2.5 mm
Allen key.
2. Set to the required staple leg length.
3. Tighten the locking screw.
The depth of the stapling claws is easily adjusted using
the setting knob. Depress the knob and turn it to the
required position.
- Shallow stapling
= Deep stapling
It is possible to adjust how tightly the staple is closed.
Turn the adjusting nut clockwise (A) to close the staple
tightly and anticlockwise (B) to close it less tightly.
Tool use
5© Josef Kihlberg AB 2007
15
18
21
22
5/8"
3/4"
13/16"
7/8"
2,2 0,9
34,8
EN
Only use original JK560 staples (15 or 18 mm leg length).
Load the magazine as follows:
1. Hold the pusher by its finger grip and pull the pusher back
until it latches in the magazine.
2. Insert two sticks of staples into the magazine.
3. Lift the finger grip up to release the latch. Move the pusher
forward until it is touching the rearmost staple stick.
Stapling cardboard:
4. Hold the tool against the cardboard (A). Then pull the
trigger (B). The tool automatically returns to the first position.
Then move the tool and pull the trigger to fire the next staple.
Tool use
6© Josef Kihlberg AB 2007
EN
The employer is responsible for ensuring that:
these Operating Instructions and appended documents
are made available to all personnel concerned, and that
they read, understand and comply with the instructions;
the personnel operating the tool are sufficiently trained
and are well aware of the risks of accident, appropriate
working methods and tool maintenance;
general safety regulations, and specific regulations with
respect to minors working with nail guns/stapler tools,
are complied with;
personnel are given the instructions, equipment and time
to perform daily tool inspection.
Please read these safety precautions carefully to prevent
injury to yourself and others. Refer to the later sections for
additional information.
To prevent eye injuries, the operator and others in the
work area should wear eye protection.
Ear protection and other personal protection equipment
should also be worn as required.
Never use oxygen, combustible gases, CO2, steam
or high pressure gas tanks as power sources for the PN
(pneumatic) version of this tool as these may cause the tool
to explode and cause serious injury. Only use dry, clean,
regulated compressed air to power the tool.
Never use a defective tool. Inspect the tool every day
to ensure that the trigger is working properly and that all
screws and nuts are secured tightly.
•
•
•
•
Safety precautions
7© Josef Kihlberg AB 2007
EN
Safety precautions
It is not permissible to make changes or modifications to
this tool or set it up in a jig without the manufacturer’s ap-
proval.
Always disconnect the tool from the air supply and empty the
magazine when you leave the tool for breaks, at the end of
the day, when troubleshooting, or when carrying out mainte-
nance or repairs. Never leave a loaded tool unattended.
Always assume that the tool is loaded. This is a working
implement and not a toy. Never point the tool at yourself or
anyone else, whether it contains staples or not. Always re-
move your finger from the trigger when not driving staples.
Avoid personal injury. Never hold your hand or any other
part of your body under the tool. Always place yourself in a
firmly balanced position when using the tool.
Connect the tool to the compressed air system before the
fastener unit is loaded. The maximum permitted air pressure
for the tool is 8 bar (116 psi). The maximum supply pressure
is 8.8 bar (127 psi). Make sure that the minimum internal di-
ameter of the air hose is 6 mm (1/4") and that of the nipple is
a minimum of 5 mm (6/32"). This will prevent incorrect opera-
tion due to a significant drop in pressure. The tool and the
hose must be fitted with a connection nipple that automati-
cally bleeds the tool when it is disconnected.
8© Josef Kihlberg AB 2007
Troubleshooting
Always disconnect the tool from the air supply, empty the
magazine and read the Safety precautions section before
you begin troubleshooting. Normally it is not necessary to
dismantle any parts in order to remove a defective staple
from the front nozzle plate. Grip the staple with a pair of flat-
nosed pliers at the exit from the front nozzle plate. Carefully
pull out the staple.
All safety devices must be inspected daily to ensure that
they are working properly. Make especially sure that:
the trigger and safety yoke move freely without binding;
all screws and nuts are securely tightened.
This tool does not require special servicing. It only needs
regular cleaning with a non-aggressive cleaning agent. Do
not remove any parts for cleaning purposes.
Apply a small amount of lubricating oil to the nipple of the
tool every day or approximately 10 drops once a week to
maximize the life and utility of the tool. For high-frequency
stapling, we recommend oil-mist lubrication. Please contact
our agent for advice. Oil recommendation.
Part no.:
1 litre 184314
0.2 litre 733007
Sliding parts have been lubricated with multipurpose
grease at the factory. We recommend using multipurpose
grease on moving parts after they have been cleaned or
replaced.
•
•
Maintenance
EN
9© Josef Kihlberg AB 2007
EN
Technical specification
The maximum permitted air pressure for the tool is 8 bar
(116 psi). The maximum supply pressure is 8.8 bar (127 psi).
Air consumption per driving operation: 0.95 l at 6 bar
operating pressure.
Characteristic noise emission level as per EN 12549.
A-weighted single-event emission sound pressure level at
work station: LPA,1s = 84dB
A-weighted sound energy level: LJA = 89dB
The vibration level is below the limit as stated in the
Declaration of Conformity EN 792-13 measured according
to ISO 8662-11.
•
•
•
•
•
•
10 © Josef Kihlberg AB 2007
Spare parts drawing
To achieve optimal performance and safety, only use
original spare parts. All repairs must be carried out by an
authorised JK workshop.
EN
© Josef Kihlberg AB 2007
11© Josef Kihlberg AB 2007
EN
Ref Part Qty Description
length = 60 mm
143109 O-ring kit a,c,R PN
143110 Repair kit a560PN
1 946760 8 Screw
2 190204 1 Top cap
3 148064 2 Gasket
4 190203 1 Cylinder
5 149057 1 Piston stop
6 946004 1 Nut
7 972115 1 O-ring
8 191204 1 Piston a560 c561PN
9 947015 1 Washer
10 191205 1 Piston a,c,R
11 950006 1 Fix ring
12 146245 1 Clinch adjustment nut
13 972142 1 O-ring
14 139525 1 Casting
15 150421 1 Cage
16 139542 1 Front Section
17 165124 1 Penetration control knob
18 173155 1 Spring
19 946651 1 Screw
20 176417 2 Anvil holder
21 945096 4 Pin
22 147127 2 Spacer
23 158303 2 Anvil hook 15-18mm
24 946687 2 Screw
25 945115 2 Pin
26 163322 2 Link
27 161355 1 Connecting yoke
28 960020 1 Latch
29 145171 2 Pin
30 164295 1 Driver blade a560
31 150420 1 Bushing
32 163321 1 Penetration eccentric
33 946696 1 Screw
34 162991 1 Rear nozzle plate a560
35 110306 1 Lable magazines
37 946769 3 Screw
38 170174 1 Magazine lid a560, c561
39 174074 1 Feeder spring
40 161354 1 Pusher a560 c561
41 951020 2 Retainer
42 165122 1 Finger grip
43 145166 1 Shaft
44 150414 1 Roller
45 946518 1 Screw
46 155157 1 Rear body
47 946780 11 Screw
48 162993 1 Front nozzle plate
49 946761 2 Screw
50 947062 2 Washer
51 945116 1 Pin
52 133179 1 Trigger compl
53 972084 1 O-ring
54 972077 1 O-ring
55 147128 1 Washer
56 173185 1 Spring
57 191206 1 Stem
58 179114 1 Rear cap
59 972176 2 O-ring
60 187062 1 Tube
61 176424 1 Hanger
62 946780 11 Screw
63 110313 1 CE Lable
64 110303 1 Tool lable
65 136169 1 Valve a,c,R
66 972030 1 O-ring
67 972020 1 O-ring
70 134307 1 Piston cpl a560, c561PN
71 134308 1 Clinch unit compl. a560PN
72 132796 1 Rail assembly
73 139526 1 Handle cpl
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Josef Kihlberg Utensili
Josef Kihlberg
Josef Kihlberg JK20T779L Manuale utente
Josef Kihlberg
Josef Kihlberg JK10-670 Manuale utente
Josef Kihlberg
Josef Kihlberg JK20T Manuale utente
Josef Kihlberg
Josef Kihlberg JK10 Manuale utente
Josef Kihlberg
Josef Kihlberg JK20-689L Manuale utente
Josef Kihlberg
Josef Kihlberg F560PN Manuale utente
Josef Kihlberg
Josef Kihlberg JK35T590 Manuale utente
Josef Kihlberg
Josef Kihlberg JK20V779L22 Manuale utente
Josef Kihlberg
Josef Kihlberg R557PN Manuale utente
Josef Kihlberg
Josef Kihlberg JK20-690 Manuale utente
Josef Kihlberg
Josef Kihlberg F53PN Manuale utente
Josef Kihlberg
Josef Kihlberg JK20A680 Manuale utente
Josef Kihlberg
Josef Kihlberg JK20V779L Manuale utente
Josef Kihlberg
Josef Kihlberg JK20-680 Manuale utente
Josef Kihlberg
Josef Kihlberg JK20 Manuale utente
Josef Kihlberg
Josef Kihlberg JK20A680L Manuale utente
Josef Kihlberg
Josef Kihlberg JK35-590 Manuale utente
Josef Kihlberg
Josef Kihlberg R555PN Manuale utente
Josef Kihlberg
Josef Kihlberg JK20-670 Manuale utente
Josef Kihlberg
Josef Kihlberg JK35-590 Manuale utente
