Keysight Technologies N9030A Manuale di installazione e funzionamento

Option MTU, MultiTouch User Interface Upgrade Kit

Option MTP, MultiTouch User Interface Upgrade Kit

with PC6 CPU

Keysight Technologies

N9030A PXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9030-90098

Edition

Edition 1, July 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9030-90098 3

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Introduction

This installation note explains how to install the hardware and licenses to add the MultiTouch user

interface to N9030A PXA signal analyzers.

This installation note supports two kits:

N9030AK-MTU - MultiTouch User Interface Upgrade

N9030AK-MTP - MultiTouch User Interface Upgrade with PC6 CPU

The N9030AK-MTU should only be installed on N9030As that already have the PC6 CPU. This kit

includes a new SSD, to ensure that when a disk drive recovery is performed, the software version

recovered will be new enough to recognize the MultiTouch front panel assembly.

The N9030AK-MTP should be installed on N9030As that do not have a PC6 CPU. A PC6 CPU is

included in this kit, along with a new SSD.

Part of the upgrade process is the license transformation process, which creates new licenses to

replace those of the existing measurement applications. This is because older measurement

application licenses whose model numbers end in the letters "A" or "B" (for example, N9071A or

N9082B) will not work with the new MultiTouch user interface. The license transformation process

will replace "A" and "B" licenses with their equivalent "C" license. For example, N9071A-2FP will be

replaced with N9071C-2FP and N9082B-1FP will be replaced with N9082C-1FP.

Products Affected: N9030A PXA Signal Analyzer

Serial Numbers: All

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

1.5 Hours

3.0 Hours

4.0 Hours

4Installation Note N9030-90098

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

IMPORTANT Once this upgrade is performed, the analyzer will only recognize

measurement applications whose model number ends in a "C". For example,

the N9068C, Phase Noise measurement application or the N9071C

GSM/EDGE measurement application.

If the current version of instrument software does not support one of the

transformed licenses, the description as displayed in the Show System

screen will include the phrase "Dormant License UI Conversion". For example,

"N9064A Dormant License UI Conversion, VXA app".

The hardware included in the kit may come in several boxes inside the shipping container

Installation Note N9030-90098 5

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

N9030AK-MTU, MultiTouch User Interface Upgrade Kit Parts List

Quantity Description Keysight Part Number

1 Front Frame Assembly, MultiTouch, Light Color N9020-60261

1 Trim Strip, Top, Benchtop, Light Color N9020-40017

1Trim Strip, top, Opt PRC, Light Colora

a. This trim strip is not used for the N9030A; Opt PRC is not supported on the N9030A

N9020-40019

1 Vibration Mount 0460-2725

2 Trim, Side, 177.0 H 5041-9172

1 Plug, Dome, 0.312 in. diameter, black 6960-0076

1 Core Bracket, Top N9020-00071

1 Core Bracket, Bottom N9020-00072

1 Knob, RPG, Large W1312-40017

1 Solid State Drive Replacement, WES7 -----------

3 Screws, M3 x 0.5 (8 mm long) pan head 0515-0372

9 Screws, M3 x 0.5 (8 mm long) flat head 0515-2032

1 Overlay, BBIQ Top, MultiTouch, Light Color N9020-80192

1 Overlay, BBIQ Bottom, MultiTouch, Light Color N9020-80193

1 Nameplate, 3.6 GHz, MultiTouch, N9030A N9030-80055

1 Nameplate, 8.4 GHz, MultiTouch, N9030A N9030-80056

1 Nameplate, 13.6 GHz, MultiTouch, N9030A N9030-80057

1 Nameplate, 26.5 GHz, MultiTouch, N9030A N9030-80058

1 Nameplate, 43 GHz, MultiTouch, N9030A N9030-80059

1 Nameplate, 44 GHz, MultiTouch, N9030A N9030-80060

1 Nameplate, 50 GHz, MultiTouch, N9030A N9030-80061

1 Overlay, Connector, Blank, quartz gray N9020-80140

1 Overlay, Keypad, quartz gray N9020-80165

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

6Installation Note N9030-90098

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

N9030AK-MTP, MultiTouch User Interface with PC6 CPU Upgrade Kit Parts List

Quantity Description Keysight Part Number

1 Front Frame Assembly, MultiTouch, Light Color N9020-60261

1 Trim Strip, Top, Benchtop, Light Color N9020-40017

1Trim Strip, top, Opt PRC, Light Colora

a. This trim strip is not used for the N9030A; Opt PRC is not supported on the N9030A

N9020-40019

1 Vibration Mount 0460-2725

2 Trim, Side, 177.0 H 5041-9172

1 Plug, Dome, 0.312 in. diameter, black 6960-0076

1 Core Bracket, Top N9020-00071

1 Core Bracket, Bottom N9020-00072

1 Knob, RPG, Large W1312-40017

1 CPU Module 2.6 GHz Quad Core 16 GB RAM, no HDD W1312-60141

1 Tray Assembly, solid state drive, 160 GB W1312.60302

3 Screws, M3 x 0.5 (8 mm long) pan head 0515-0372

9 Screws, M3 x 0.5 (8 mm long) flat head 0515-2032

1 Overlay, BBIQ Top, MultiTouch, Light Color N9020-80192

1 Overlay, BBIQ Bottom, MultiTouch, Light Color N9020-80193

1 Nameplate, 3.6 GHz, MultiTouch, N9030A N9030-80055

1 Nameplate, 8.4 GHz, MultiTouch, N9030A N9030-80056

1 Nameplate, 13.6 GHz, MultiTouch, N9030A N9030-80057

1 Nameplate, 26.5 GHz, MultiTouch, N9030A N9030-80058

1 Nameplate, 43 GHz, MultiTouch, N9030A N9030-80059

1 Nameplate, 44 GHz, MultiTouch, N9030A N9030-80060

1 Nameplate, 50 GHz, MultiTouch, N9030A N9030-80061

1 Overlay, Connector, Blank, quartz gray N9020-80140

1 Overlay, Keypad, quartz gray N9020-80165

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

Installation Note N9030-90098 7

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Tools Required

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— Deep 5/16-inch socket wrench

— ¼-inch open-end wrench

— Scissors or knife

—Diagonalcutters

— Microsoft Windows based personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

8Installation Note N9030-90098

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show, System. Make note of the

following information from the Show System screen:

Product Number: _____________

Serial Number: ______________

Instrument S/W Revision: ______________

3. Check for the presence of one of the following options listed below in the Show System

screen. Put a check mark or “X” after the option listed below that appears in the Show System

screen.

N9030A-PC2_____

N9030A-PC4_____

N9030A-PC6_____

N9030A-EXM_____

N9030A-BBA_____

4. Refer to the data in step 2 above. If the Product Number is not N9030A, do not proceed with

the installation of this kit. This kit is to be installed only on N9030A signal analyzers.

5. Refer to the data in step 3 above. If upgrade product N9030A-MTU is being installed and the

currently installed CPU is either N9030A-PC2 or N9030A-PC4, do not proceed with the

installation of this kit. This kit is to be installed only on N9030A signal analyzers with

N9030A-PC6 CPUs.

6. Refer to the data in step 3 above. If the upgrade product N9030A-MTP is being installed and

the currently installed CPU is N9030A-PC6, do not proceed with the installation of this kit. This

kit is to be installed only on N9030A signal analyzers with N9030A-PC2 or N9030A-PC4 CPUs.

7. Refer to the data in step 3 above. If either option N9030A-EXM or N9030A-BBA is installed,

there will be additional steps required to remove and replace the front panel assembly.

Installation Note N9030-90098 9

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

License Key Backup

In order for the instrument being upgraded to keep the same option configuration that it had prior

to the upgrade, it is mandatory that the licenses be transferred from the original disk drive to the

new disk drive. In most cases, these licenses will be automatically copied from the Midplane board

assembly. However, there may be instances where the automatic copying process will not work.

Therefore, the license keys will also be backed up for later restoration on the new disk drive.

1. Connect a mouse and external keyboard to the analyzer using the rear panel USB ports.

2. Locate a USB storage device. Perform a virus scan on this device before use.

3. Create a folder on the USB storage device with the folder name "Licenses" followed by the

model number and serial number of the analyzer being upgraded. For example,

"Licenses_N9030A_MY49430501"

4. Insert the USB storage device into one of the analyzer's USB ports.

5. Using the mouse, navigate to the folder C:\Program Files\Agilent\licensing.

6. Change the folder's properties so that hidden files can be viewed.

a. If the operating system is WinXP, click on Tools and select Folder Options. Select the View

tab. In the Advanced Settings window, under Hidden files and folders, select "Show hidden

files and folders".

b. If the operating system is Windows Embedded Standard 7 (WES7), click on Organize and

select Folder and search options. Select the View tab. In the Advanced Settings window,

under Hidden files and folders, select "Show hidden files and folders".

7. Copy the contents of the C:\Program Files\Agilent\licensing folder to the Licenses… folder

created on the USB storage device.

a. To select all of the licenses in the folder, click on any of the licenses and then press Ctrl-A

on the external keyboard.

b. To copy the selected files, press Ctrl-C.

c. Navigate to the "Licenses_..." folder on the USB storage device for the instrument being

upgraded and press Ctrl-V to paste all the licenses into the folder.

10 Installation Note N9030-90098

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Backup Calibration Data

1. With the instrument turned on and the signal analyzer application running as normal, connect

a USB mouse to one of the instrument USB ports.

2. Locate a USB storage device and insert it into one of the available instrument USB ports.

(Perform a virus scan on this device before use)

3. On the front panel of the instrument, press System, Alignments, Backup or Restore Align

Data.... Click on OK. The signal analyzer application will close and the Alignment Data Wizard

will start. This might take a few minutes.

4. The Alignment Data Wizard window as shown in Figure 1 will appear.

Figure 1 Alignment Data Wizard

5. Follow the on-screen instruction to Backup the calibration data to the USB memory device.

Altri manuali per N9030A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Keysight Technologies Strumento di misura

Keysight Technologies

Keysight Technologies 34980A Manuale utente

Keysight Technologies

Keysight Technologies EXA N9010A Manuale utente

Keysight Technologies

Keysight Technologies B2900 Series Manuale utente

Keysight Technologies

Keysight Technologies B2901A Manuale utente

Keysight Technologies

Keysight Technologies N5252A Manuale utente

Keysight Technologies

Keysight Technologies N9040B Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies 34921A Manuale utente

Keysight Technologies

Keysight Technologies N5250C PNA Series Manuale utente

Keysight Technologies

Keysight Technologies N5244BU-679 Manuale utente

Keysight Technologies

Keysight Technologies X Series Manuale utente

Keysight Technologies

Keysight Technologies BT2152A Manuale di servizio

Keysight Technologies

Keysight Technologies P5000A Series Manuale utente

Keysight Technologies

Keysight Technologies FieldFox N9923A Manuale utente

Keysight Technologies

Keysight Technologies E4980A Manuale utente

Keysight Technologies

Keysight Technologies 34959A Manuale utente

Keysight Technologies

Keysight Technologies N9030B Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies X Series Manuale del proprietario

Keysight Technologies

Keysight Technologies N1913PM5B Guida rapida

Keysight Technologies

Keysight Technologies PNA-X N5241A Manuale utente

Keysight Technologies

Keysight Technologies N9030B Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies E5061B Manuale utente

Keysight Technologies

Keysight Technologies Streamline Series Manuale utente

Keysight Technologies

Keysight Technologies 16034G Manuale utente

Keysight Technologies

Keysight Technologies N9000B Manuale di installazione e funzionamento

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente