Keysight Technologies N9040B Manuale di installazione e funzionamento

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement

business has become Keysight Technologies. For more

information, go to www.keysight.com.

Keysight Technologies

N9040B UXA Signal Analyzer

Option B2X, 255 MHz Analysis Bandwidth

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9040-90017

Supersedes None

Edition

Edition 1, April 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9040-90017 3

Option B2X, 255 MHz Analysis Bandwidth

Introduction

This installation note explains how to install Option B2X, 255 MHz Analysis Bandwidth, into a UXA

signal analyzer.

The option is licensed for one instrument model number/serial number combination. The license

file that is downloaded from the web will only install on the designated instrument.

Products Affected UXA N9040B

Serial Numbers: All

To Be Performed By: (X) Keysight Service Center

( ) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

2.0 Hours

6.0 Hours

4.0 Hours

4Installation Note N9040-90017

Option B2X, 255 MHz Analysis Bandwidth

Contents

Tools Required

— Personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

— T-10 TORX Driver

— T-20 TORX Driver

— Keysight Calibration and Adjustment Software, N7814A (revision E.16.00 or later required)

— Test equipment and computer supported by the Keysight Calibration and Adjustment Software

— UXA Signal Analyzer Service Guide, N9040-90006. Available online.

Quantity Description Keysight Part Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

1 Wideband Analog IF assembly N9020-60043

1 Wideband Digital IF assembly N9020-60311

1 Flex Circuit, WB DIF to Flex Circuit Interconnect Bracket N9040-60045

1 Flex Circuit, WB AIF to Flex Circuit Interconnect Bracket N9040-60042

1 Bracket, Flex Circuit Interconnect N9040-00025

1 Spring Clip (for flex cable) N9040-00035

1 Cable Kit N9040-60070

4 Screw, Pan Head, M3 x 0.5 8 mm long 0515-0372

15 Screw, Flat Head, M3 x 0.5 6 mm long 0515-1946

Installation Note N9040-90017 5

Option B2X, 255 MHz Analysis Bandwidth

Initial Instrument Functionality Check

1. Power on the instrument and allow the instrument to boot up, run the alignments and display

the measurement screen. The instrument will probably display a spectrum analyzer screen and

you will see the instrument sweeping.

2. There should be no alignment failures. If there are failures, investigate and fix the problem

before continuing.

6Installation Note N9040-90017

Option B2X, 255 MHz Analysis Bandwidth

Wideband Analog IF Assembly Hardware Installation

1. Power down the instrument, wait until the standby light comes on, and remove the power

cord.

2. Remove the instrument side strap handles, feet, outer case, top brace front, top brace rear,

and remove the rear panel (be careful to not damage the cables), and remove the rear brace.

See the UXA Service Guide Assembly Replacement Procedure section for A22 and A23 WB

Digital IF Boards. Save all screws for reuse.

3. Disconnect the gray ribbon cable from the rear motherboard. This cable runs from the front of

the instrument, and must be disconnected to allow the Wideband Analog IF to be installed.

4. Locate the Wideband Analog IF Assembly and the N9040-60042 Flex Circuit Cable in the kit.

Install the Flex Circuit cable into the connector on the Wideband Analog IF Assembly. This flex

cable will be connected to the other flex cable in the kit later in the installation process.

5. Install the Wideband Analog IF into card cage connectors J8 and J10. See Figure 1.

6. Locate 2, 0515-1946 flat head screws in the kit and secure the board brackets to the chassis

using these screws (1). Torque to 9 inch-pounds.

Figure 1 Wideband Analog I.F. Installed in Card Cage

7. Locate the gray coax cables in the kit. Find the short cable, W46, with color code 1 on one end,

and color codes 726 on the other end. Attach the color code 1 end of the cable to the

Wideband Analog IF at J1 as shown in Figure 1. Attach the other end of the cable to the

Reference board J726.

Installation Note N9040-90017 7

Option B2X, 255 MHz Analysis Bandwidth

8. Locate the W45 cable with color code 2 on one end and 17 on the other end. Attach color code

2 end to the Wideband Analog IF at J2. Route the cable as shown in Figure 2, the other end of

the cable will be routed later to the A3 Digital IF.

9. Locate the W34 cable with color code 4 at one end and color code 718 at the other end. Attach

the color code 4 end to Wideband Analog IF at J4, and the other end to A16 Reference

assembly at J718.

10.Locate W41 cable with color code 17 at one end and color code 901 at the other end. Attach

the color code 17 end to the Wideband Analog IF at J17, and the other end to A15 Front End

Controller at J901. Remove cable that is on A15J901, it will be discarded after the other end of

the cable at A3J15 is removed later.

11.Locate W40 cable with color code 18 at one end and color code 15 at the other end, Attach the

color code 18 end to the Wideband Analog IF at J18. The other end of the cable will be routed

to the A3 Digital IF assembly.

12.See Figure 2 that shows the hole in the chassis the W40 cable routes through in order to

connect to A3J15.

Figure 2 Cable Routing

8Installation Note N9040-90017

Option B2X, 255 MHz Analysis Bandwidth

13.See Figure 3 that shows where the color code 15 end of W40 connects to the A3J15, Digital IF

assembly.

Figure 3 DIF Cables Showing W40 Connection to J15

Installation Note N9040-90017 9

Option B2X, 255 MHz Analysis Bandwidth

Wideband Digital IF Assembly Hardware Installation

14.See Figure 4. Locate the Wideband Digital IF assembly in the kit. Install the assembly into the

top card slot as shown.

Figure 4 Wideband Digital I.F. Installation

15.Locate the N9040-60045 Flex Circuit cable in the kit and connect one end to the Wideband

Digital IF assembly and the other end to the Flex Cable previously installed on the Wideband

Analog IF assembly.

16.Locate the "Bracket, Flex Circuit Interconnect" in the kit. This bracket secures the flex circuit

connection you made in the previous step. See Figure 4. attach the flex cable connection to

the interconnect bracket using the two flat head screws (1), and mount the interconnect

bracket to the instrument frame using a pan head screw (2) and torque to 9 inch-pounds.

10 Installation Note N9040-90017

Option B2X, 255 MHz Analysis Bandwidth

17.Locate the spring clip in the kit. Install the spring clip to secure the flex circuit connection on

the Wideband Digital IF assembly.

18.Re-install the Rear Brace and the Rear Panel. An additional flat head screw, 0515-1946 is

required to secure the new Wideband Digital IF assembly to the rear panel. This flat head

screw is in the bag of screws in the kit. Torque to 9 inch-pounds

19.Re install the front top brace and use the 0515-1946 flat head screws in the kit in the

countersunk locations. Torque to 9 inch-pounds.

20.Reinstall the rear top brace and outer case, side strap handles, and feet.

21.Power up the instrument. Assure the instrument passes the auto alignments

Altri manuali per N9040B

Indice

Altri manuali Keysight Technologies Strumento di misura

Keysight Technologies

Keysight Technologies EXA N9010B Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies 34980A Manuale utente

Keysight Technologies

Keysight Technologies EXA N9010B Guida rapida

Keysight Technologies

Keysight Technologies Agilent Technologies PXI Express M9202A Guida utente

Keysight Technologies

Keysight Technologies E5061B ENA Series Manuale utente

Keysight Technologies

Keysight Technologies P Series Manuale utente

Keysight Technologies

Keysight Technologies M9260A Guida utente

Keysight Technologies

Keysight Technologies E5072A Manuale utente

Keysight Technologies

Keysight Technologies E4990A Manuale utente

Keysight Technologies

Keysight Technologies B2981A Guida all'installazione

Keysight Technologies

Keysight Technologies N9020A Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies N778 C Series Istruzioni operative

Keysight Technologies

Keysight Technologies U1281A Manuale utente

Keysight Technologies

Keysight Technologies U1401B Manuale utente

Keysight Technologies

Keysight Technologies B1505A Manuale utente

Keysight Technologies

Keysight Technologies 16861A Manuale utente

Keysight Technologies

Keysight Technologies M9391A PXIe Manuale utente

Keysight Technologies

Keysight Technologies EXA N9010B Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies FieldFox N9923A Manuale utente

Keysight Technologies

Keysight Technologies N9020A Manuale di installazione e funzionamento

Keysight Technologies

Keysight Technologies N5221A Manuale utente

Keysight Technologies

Keysight Technologies M9391A PXIe Guida utente

Keysight Technologies

Keysight Technologies MXA N9020A-508 Manuale utente

Keysight Technologies

Keysight Technologies FieldFox N9913A Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente