Keysight Technologies EXA N9010B Guida rapida
Option EXM, External Mixing Upgrade Kit
Keysight N9010B EXA
Signal Analyzer
Installation Note
Notice.
© Copyright 2016 - 2017 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9010-90067
Edition
Edition 2, March 2017
Supersedes February 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9010-90067 3
Option EXM, External Mixing Upgrade Kit
Option EXM, External Mixing Upgrade Kit
Software and test equipment is required for making adjustments and for performance verification
testing.
Information on how to obtain this software can be found at:
www.keysight.com/find/calibrationsoftware
While Keysight does recommend that a full calibration be performed after the installation of this
upgrade, the end user must ultimately determine whether they want this service or not. If a full
calibration is required, arrangements regarding the level of calibration must be made between the
end user and the calibration provider.
Introduction
This kit includes parts to upgrade an EXA signal analyzer with frequency range Option 532 or 544 to
add Option EXM, External Mixing.
In addition to installing the hardware to support Option EXM, a license for the following option will
also be installed:
— N9010B-EXM, External Mixing
Products Affected: N9010B EXA
Serial Numbers: All
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
1.5 Hours
1.0 Hoursa
1.0 Hoursa
a. To ensure that these newly installed options are functioning properly, the procedure that follows
includes the requirement of performing certain adjustments and performance verification tests.
However, the completion of these tests does not guarantee that the instrument meets all advertised
specifications.
4Installation Note N9010-90067
Option EXM, External Mixing Upgrade Kit
Installation Kit Parts List
Quantity Description Keysight Part Number
1 Adapter- Coaxial Straight Female-SMA to Female-SMA, 50W 1250-1666
1 Washer, Lock, Internal Tooth, ¼ inch 2190-0067
1 Nut-Hex-Double-Chamfer 1/4-36-THD.125-IN-THK, Stainless Steel 2950-0223
1 50 Ohm Termination, SMA male 1810-0118
1 Opt EXM Cable Kit with Wire Markers
(includes cable W26, listed below)
N9010-60009
1 Cable Assembly, External Mixing, Front Panel (W27) N9020-20166
1 Cable Assembly, mmW Front End to W27 (W28)
(for use in millimeter wave analyzers)
N9020-20296
1 Cable Assembly, Coaxial 275 mm LG (W26)
(for use in millimeter wave analyzers) 8121-2025 awith ends
labeled ‘903’ and ‘13’
a. This cable is included in the Opt EXM Cable Kit with Wire Markers, p/n N9010-60009.
1 Label, Warning N9030-80018
5 Cable Ties 1400-0249
12 Screw, M3 x 0.5, (6 mm long), flathead 0515-1946
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
1 Installation Note This note
Installation Note N9010-90067 5
Option EXM, External Mixing Upgrade Kit
Tools Required
— T-10 TORX Driver
— T-20 TORX Driver
— 5/16-inch torque wrench
— ¼-inch open-end wrench
—Diagonalcutters
— Keysight Calibration and Adjustment Software, N7814A (revision E.16.00 or later)
— Test equipment and computer supported by the X- Series Performance Tests and Adjustment
Software
— EXA Signal Analyzer Service Guide. This manual is available online at the following URL:
www.keysight.com/find/N9010B_service_guide
— Microsoft Windows based personal computer with internet access and USB port
— USB storage device with > 2 GB free memory
Initial Instrument Functionality Check
Power on the instrument and allow the instrument to boot up. Run an alignment and display the
measurement screen. (The instrument will probably display a spectrum analyzer screen and you will
see the instrument sweeping.)
There should be no alignment failures. If there are failures, investigate and fix the problem before
continuing.
Before you disassemble the instrument, turn the power switch to Standby. After the instrument
has completely shut down, unplug the instrument. Failure to unplug the instrument can result in
personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.
6Installation Note N9010-90067
Option EXM, External Mixing Upgrade Kit
Installation Procedure
1. Connect a power cord to the analyzer and turn on the analyzer.
2. After the analyzer has completed turning on, press System, Show System. Make note of the
following information from the Show System screen:
Product Number: _____________
Serial Number: ______________
Instrument S/W Revision: ______________
3. Check for the presence of one of the following frequency range options listed below in the
Show System. Put a check mark or “X” after the frequency range option listed below that
appears in the Show System menu.
N9010A-503_____
N9010A-507_____
N9010A-513_____
N9010A-526_____
N9010A-532_____
N9010A-544_____
4. If the analyzer is equipped with any of the following frequency range options (refer to the data
in step 3 above):
N9010A-503
N9010A-507
N9010A-513
N9010A-526
do not proceed with the installation of this upgrade kit.
An RF or microwave EXA is not compatible with Option EXM.
Installation Note N9010-90067 7
Option EXM, External Mixing Upgrade Kit
Analyzer Disassembly
Standard Instrument
1. Disconnect the instrument from ac power.
2. Refer to Figure 1, “Instrument Outer Case Removal,”. Using the T-20 driver, remove the 4
screws (1) (two on each side) that attach the handle strap (2) on each side of the instrument.
3. Remove the four key locks from the instrument four bottom feet.
4. Remove the four instrument bottom feet.
5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet
(4) in place.
6. Pull the instrument cover (5) off towards the rear of the instrument.
If the instrument is placed on its face during any of the following procedures, be sure to use a soft
surface or soft cloth to avoid damage to the front panel, keys, or input connector.
Make sure any adapters on the front panel are removed.
If the analyzer has Option PRC, Portable Configuration, refer to the "Option PRC." section on
page 9 to remove the outer case.
8Installation Note N9010-90067
Option EXM, External Mixing Upgrade Kit
Figure 1 Instrument Outer Case Removal
Installation Note N9010-90067 9
Option EXM, External Mixing Upgrade Kit
Option PRC
1. Disconnect the instrument from ac power.
2. Refer to Figure 2, “Bail Handle Removal,”. Using the T-20 driver, remove the four screws (two
on each side) (1) that hold the bail handle (2) to the front frame.
Figure 2 Bail Handle Removal
3. Using the T-20 driver, remove the four screws (two on each side) (6) that hold the strap
handle plugs (5) in place.
10 Installation Note N9010-90067
Option EXM, External Mixing Upgrade Kit
4. Refer to Figure 3, “Option PRC Outer Case Removal,”. Using the T-20 driver, remove the four
screws (including washers) (1) that hold the rear bumpers (2) (two on each side) in place.
Figure 3 Option PRC Outer Case Removal
5. Pull the instrument cover (3) off towards the rear of the instrument.
Altri manuali per EXA N9010B
2
Indice
Altri manuali Keysight Technologies Strumento di misura
Keysight Technologies
Keysight Technologies V3500A Manuale utente
Keysight Technologies
Keysight Technologies S9106AC-2IF Guida utente
Keysight Technologies
Keysight Technologies B2900A Series Manuale utente
Keysight Technologies
Keysight Technologies N5222B Guida rapida
Keysight Technologies
Keysight Technologies N774 C Series Manuale utente
Keysight Technologies
Keysight Technologies 16861A Manuale utente
Keysight Technologies
Keysight Technologies 8163A/B Istruzioni operative
Keysight Technologies
Keysight Technologies N437 Series Istruzioni per l'installazione e il funzionamento
Keysight Technologies
Keysight Technologies B2901A Manuale utente
Keysight Technologies
Keysight Technologies N9029AV01-V15 Manuale utente
Keysight Technologies
Keysight Technologies UXA N9040B Manuale utente
Keysight Technologies
Keysight Technologies N9000B Manuale di installazione e funzionamento
Keysight Technologies
Keysight Technologies N8262A P Series Manuale utente
Keysight Technologies
Keysight Technologies 11590B Manuale di servizio
Keysight Technologies
Keysight Technologies N9340B Manuale utente
Keysight Technologies
Keysight Technologies P50 B Series Manuale utente
Keysight Technologies
Keysight Technologies CX3300 Series Manuale utente
Keysight Technologies
Keysight Technologies E5260 Series Istruzioni operative
Keysight Technologies
Keysight Technologies N9000A Manuale di installazione e funzionamento
Keysight Technologies
Keysight Technologies N9029AV01-V19 Manuale utente
Keysight Technologies
Keysight Technologies IntegraVision PA2200 Series Manuale di servizio
Keysight Technologies
Keysight Technologies N4374B Manuale utente
Keysight Technologies
Keysight Technologies U5855A Manuale utente
Keysight Technologies
Keysight Technologies N524 A Series Manuale di installazione e funzionamento
