LINSHANG LS131 Manuale utente
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 1 of 9
LS131
UV Energy Meter
User Manual V2.0
Please read this manual carefully before using and reserve it for reference.
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 2 of 9
I. Product Introduction
UV Energy meter can measure the UV energy, UV irradiance simultaneously and record UV power data
as well as the power curve. It can be used to measure the UV irradiance and energy of the machine which
using UV LED light source, such as UV drying machine, exposure machine and printing machine.
II. Parameters
1. Spectral range: 340nm-420nm, calibrated at 395nm
2. Irradiance measuring range: 0-40000mW/cm²
3. Irradiance resolution: 1mW/cm²
4. Energy measuring range: 0-999999mJ/cm²
5. Energy measuring accuracy: ±10%，±5% (typical)
6. Sampling speed: 2048 times/second
7. Irradiance data storage interval: 32 times/second
8. Recording period: 32 minutes
9. Power supply: 4 AAA alkaline dry batteries
10. Display: 240*160 Dot matrix LCD
11. Dimension: 160mm×75mm×13mm (L*W*H)
12. Weight: 303 g
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 3 of 9
III. Spectral response curve
IV. Characteristics
1. It is the real smart UV energy meter with a large LCD to display.
2. It is equipped with a USB port, and the detailed record data can be read through PC software,
generating data curve and print out test reports.
3. Equipped with metal shell, high temperature resistant design can operate at 100℃ for long time.
4. Equipped with large-capacity memory, which can record up to 60,000 pieces of power data.
5. The stored data will not be lost when the power is off and the last test data will be displayed
automatically when power is on; the test data can only be deleted manually.
6. It is with a built-in timer, and can record the UV curing time accurately.
V. Operation
1. Parameter setting
In OFF mode, long press the “POWER” button for 3 s and enter into the setting mode:
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 4 of 9
A. Trigger mode: (the measurement mode of Auto and Manual)
Short press “▲” or “▼”to choose Auto/Manual
Choose “Auto”-the auto trigger mode, the meter will start and stop automatically.
Choose “Manual”-the measurement will start and stop manually.
Short press the “ENTER” key and enter into the next setting interface. If Auto mode is selected, next
setting interface is trigger threshold value. If manual mode is selected, next setting interface is the smooth
process.
Note: For the recording time is only 32 minutes, if the production line is very long and need a long time to
reach the UV Lamp position, the “AUTO” mode must be selected.
B. Trigger threshold (Trigger power: 1-50mW/cm² can be set)
Short press “▲” or “▼” to set the trigger threshold.
Short press the “ENTER” button and enter into the smooth process.
C. Smooth Processing (Smooth: OFF/50HZ/60HZ)
If the UV lamp is powered with alternating current, the frequency of alternating current will influence the
accuracy of the irradiance measurement. Short press “▲” or “▼”to select the power supply frequency of
the light source.
OFF: this option can be selected if no smooth processing will be performed and the UV lamp is
powered with direct current
50HZ: this option must be selected if frequency of the alternating current is 50HZ
60HZ: this option must be selected if frequency of the alternating current is 60HZ
Short press the “ENTER” button to confirm the setting and the meter enters the “Standard Selection”
interface.
D. Standard Selection
Short press the “ ” button or “ ” button to select the standard.
LS-STD (Enterprise standard): The meter is calibrated according to enterprise standard.
JJG 879-2015 (Chinese standard): The meter is calibrated according to Chinese standard.
Short press the “ENTER” button to confirm the setting and the meter enters the “STOP” interface.
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 5 of 9
E. Factory default settings:
Trigger mode: Manual
Smooth: 50HZ
Standard Selection: LS-STD (Enterprise standard)
2. ON/OFF
In POWER OFF state, short press “POWER” button to power on the meter. Information such as
calibration date, production date, version number, serial number will be showed on the meter after
powering on and enter into the last measurement interface -STOP Interface. In the STOP interface,
long press the “POWER “button to power off the meter.
In the STOP interface, the meter will power off without any operation in 3 minutes.
In the state of “READY”, the longest waiting time is 50 minutes .If the measurement cannot be
triggered after 50 minutes, the meter will shut down automatically.
3. Measurement
In the measurement mode, three operation states exist:
READY: In the auto trigger mode, this means the meter is waiting for triggering to begin a measurement.
RUN: The meter is in the process of measurement.
STOP: The data measurement is over.
In measurement interface:
M: Manual Measurement
A: Automatic Measurement
1) Manual Measurement：Short press the "POWER" key, Press "ENTER" to confirm the new
measurement and clear last measured data(show-----)and enters into the measurement state after 1
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 6 of 9
second(RUN state).Short press the “POWER” key or when the measurement time reaches 32
minutes, the measurement ends and enters into the STOP interface.
2) Automatic measurement：Press the button to start the new measurement then enter into the
“READY” state and clear last measured data ,（show"-----"and flash）,When the power value is greater
than the set value of trigger power, the trigger condition is satisfied then enter into the measurement
state (RUN state) .If the recording time reaches 40 minutes or the power value is less than the set
value of trigger power, the measurement will be automatically ended and enters into the STOP
interface.
4. The last measurement data view
After power on, the meter enters into the STOP interface, which displays the real-time value, maximum
power, energy, measurement time and power curve measured last time.
In the STOP interface, short press the "ENTER" key to toggle between the measurement result and
power curve.
In the stop status, long press the "ENTER" key to clear the current test data.
5. Low Power Alarm
When the battery power is low, the battery symbol " " on the bottom right of the screen will flash,
indicating that the battery needs to be replaced.
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 7 of 9
VI. PC Software Instruction
In the STOP interface (other interfaces cannot be connected to the PC software ), plug in the USB cable,
open "UV Energy meter Vx.x" software then the meter can be connected to the computer for you to read
the data .The software has various functions,
Such as parameter configuration, data reading, UV irradiance curve, report printing and power data
saving to EXCEL.
The report generation and printing function should be specially explained. For test data, the software can
generate a report automatically and print, and if a PDF printer is installed, the electronic version report
can be printed in PDF format. This is convenient for the recording and archiving of test data.
Record data can be read by connecting USB cable with computer directly (when the meter is connected
to the computer USB port for the first time, the computer needs to be restarted so as to load the driver
automatically). Currently, the software supports Windows operating system.
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 8 of 9
VII. Precautions
1. The meter sensor needs to be facing towards the UV light source.
2. When not in use, please turn off the meter
3. Avoid contact with corrosive materials and keep away from high humidity.
4. Please put it in the plastic case after power-off and keep properly.
5. The suggested calibrating period is one year, and our company has the standard light source and
provides calibration service. (The previous calibration time “Cal date: year/month/day” will be
displayed on the boot screen.)
Shenzhen Linshang Technology Co., Ltd.
2019-7-25 Page 9 of 9
6. For the UV sensor is very sensitive to humidity, the storage environment is very important. For long
time storage, please be sure to keep the meter in dry environment.
VIII. Standard packing list
No. Description Quantity Unit
1 UV Energy Meter 1 pcs
2 USB Cable 1 pcs
3 Software USB flash disk 1 pcs
4 AAA battery 4 pcs
5 Small cross screwdriver 1 pcs
6 User Manual 1 pcs
7 Certificate/Warranty card 1 pcs
8 Plastic Case 1 pcs
IX. Service
1. The meter has one-year warranty. If the meter works abnormally, please send the whole set of meter
to our company for maintenance.
2. Provide users with spare parts and lifelong maintenance services.
3. Provide the users with the meter calibration service.
4. Free technical support for long term.
Manufacturer: Shenzhen Linshang Technology Co., Ltd.
Website: www.linshangtech.com
Service hotline: +86-755-86263411
Email: sales@linshangtech.com
Indice
Altri manuali LINSHANG Strumento di misura
LINSHANG
LINSHANG LS130 Manuale utente
LINSHANG
LINSHANG LS108 Manuale utente
LINSHANG
LINSHANG LS160A Manuale utente
LINSHANG
LINSHANG LS236 Manuale utente
LINSHANG
LINSHANG LS137 Manuale utente
LINSHANG
LINSHANG LS162A Manuale utente
LINSHANG
LINSHANG LS162 Manuale utente
LINSHANG
LINSHANG LS133 Manuale utente
LINSHANG
LINSHANG LS182 Manuale utente
LINSHANG
LINSHANG LS197 Manuale utente
LINSHANG
LINSHANG LS132 Manuale utente
LINSHANG
LINSHANG LS201 Manuale utente
LINSHANG
LINSHANG LS190 Manuale utente
LINSHANG
LINSHANG LS136 Manuale utente
LINSHANG
LINSHANG LS110 Manuale utente
LINSHANG
LINSHANG LS196 Manuale utente
LINSHANG
LINSHANG LS110A Manuale tecnico
LINSHANG
LINSHANG LS108A Manuale utente
LINSHANG
LINSHANG LS220 Manuale utente
LINSHANG
LINSHANG LS220B Manuale utente
