Makita RP0900 Manuale utente
RP0900
EN Router INSTRUCTION MANUAL 7
ZHCN 雕刻机 使用说明书 13
ID Frais Tangan PETUNJUK PENGGUNAAN 19
MS Penghala MANUAL ARAHAN 25
VI Máy Phay Cầm Tay Hoạt
Động Bằng Động Cơ Điện TÀI LIỆU HƯỚNG DẪN 32
TH 38
1
2
1
2
1
2
3
4
5
1
2
3
4
5
1
2
1
1
2
3
44
2
Fig.8
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
Fig.7
2
1
23
4
123
A
12
3
1
2
3
4
5
6
7
Fig.9
Fig.10
Fig.11
Fig.12
Fig.13
Fig.14
Fig.15
3
1
2
Fig.16
R
Fig.17
Fig.18
Fig.19
Fig.20
Fig.21
Fig.22
4
Fig.23
Fig.24
Fig.25
Fig.26
Fig.27
Fig.28
Fig.29
Fig.30
5
Fig.31
6
7ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model RP0900
Collet chuck capacity 6 mm, 1/4", 8 mm and/or 3/8"
Plunge capacity 0 - 35 mm
No load speed (min-1)27,000
Overall height 217 mm
Net weight 2.7 kg
Safety class /II
• Due to our continuing program of research and development, the specications herein are subject to change with-
out notice.
• Specications may dier from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
DOUBLE INSULATION
Wear safety glasses.
Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of the European Directive,
on Waste Electric and Electronic
Equipment and its implementation in
accordance with national law, electric
equipment that have reached the end of
their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Intended use
The tool is intended for ush trimming and proling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, re and/or serious
injury.
Save all warnings and instruc-
tions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30 mA or less is always
recommended.
8ENGLISH
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the o-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your nger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
17. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and o. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
21. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may aect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations dierent from those intended could
result in a hazardous situation.
Service
25. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
26. Follow instruction for lubricating and chang-
ing accessories.
27. Keep handles dry, clean and free from oil and
grease.
ROUTER SAFETY WARNINGS
1. Hold power tool by insulated gripping sur-
faces, because the cutter may contact its own
cord. Cutting a “live” wire may make exposed
metal parts of the power tool “live” and shock the
operator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable plat-
form. Holding the work by your hand or against
the body leaves it unstable and may lead to loss of
control.
3. Wear hearing protection during extended
period of operation.
4. Handle the bits very carefully.
5. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
6. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7. Hold the tool rmly with both hands.
8. Keep hands away from rotating parts.
9. Make sure the bit is not contacting the work-
piece before the switch is turned on.
10. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate improperly
installed bit.
11. Be careful of the bit rotating direction and the
feed direction.
12. Do not leave the tool running. Operate the tool
only when hand-held.
13. Always switch o and wait for the bit to come
to a complete stop before removing the tool
from workpiece.
14. Do not touch the bit immediately after opera-
tion; it may be extremely hot and could burn
your skin.
15. Do not smear the tool base carelessly with
thinner, gasoline, oil or the like. They may
cause cracks in the tool base.
16. Use bits of the correct shank diameter suitable
for the speed of the tool.
17. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
9ENGLISH
18. Always use the correct dust mask/respirator
for the material and application you are work-
ing with.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or famil-
iarity with product (gained from repeated
use) replace strict adherence to safety
rules for the subject product. MISUSE or
failure to follow the safety rules stated in
this instruction manual may cause serious
personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION:
• Always be sure that the tool is switched o and
unplugged before adjusting or checking function
on the tool.
Adjusting the depth of cut
► Fig.1: 1. Stopper pole 2. Screw
Place the tool on a at surface. Loosen the screw
securing the stopper pole.
Loosen the lock lever and lower the tool body until the
bit just touches the at surface. Tighten the lock lever to
lock the tool body.
► Fig.2: 1. Lock lever 2. Screw
Next, lower the stopper pole until it makes contact with
the adjusting hex bolt. Align the depth pointer with the
“0” graduation.
Raise the stopper pole until the desired depth of cut
is obtained. The depth of cut is indicated on the scale
(1 mm per graduation) by the depth pointer. Then
tighten the screw to secure the stopper pole.
Now, your predetermined depth of cut can be obtained
by loosening the lock lever and then lowering the tool
body until the stopper pole makes contact with the
adjusting hex bolt.
► Fig.3: 1. Depth pointer 2. Screw 3. Stopper pole
4. Adjusting hex bolt 5. Stopper block
CAUTION:
• Since excessive cutting may cause overload of
the motor or diculty in controlling the tool, the
depth of cut should not be more than 15 mm at a
pass when cutting grooves with an 8 mm diame-
ter bit.
• When cutting grooves with a 20 mm diameter
bit, the depth of cut should not be more than
5 mm at a pass.
When you wish to cut grooves more than 15 mm
deep with an 8 mm diameter bit or more than
5 mm deep with a 20 mm diameter bit, make
several passes with progressively deeper bit
settings.
Stopper block
► Fig.4: 1. Depth pointer 2. Screw 3. Stopper pole
4. Adjusting hex bolt 5. Stopper block
The stopper block has three adjusting hex bolts which
raise or lower 0.8 mm per turn. You can easily obtain
three dierent depths of cut using these adjusting hex
bolts without readjusting the stopper pole.
Adjust the lowest hex bolt to obtain the deepest depth
of cut, following the method of “Adjusting depth of cut”.
Adjust the two remaining hex bolts to obtain shallower
depths of cut. The dierences in height of these hex
bolts are equal to the dierences in depths of cut.
To adjust the hex bolts, turn the hex bolts. The stopper
block is also convenient for making three passes with
progressively deeper bit settings when cutting deep
grooves.
CAUTION: When using a bit having total length
of 60 mm or more, or edge length of 35 mm or more,
the depth of cut cannot be adjusted as previously
mentioned. To adjust, proceed as follows:
Loosen the lock lever and carefully adjust bit protru-
sion below the tool base to the desired depth of cut
by moving the tool body up or down. Then retighten
the lock lever to lock the tool body at that depth of cut.
Keep the tool body locked at this position during use.
Since the bit always protrudes from the tool base, be
careful when handling the tool.
Adjusting the lock lever
► Fig.5: 1. Lock lever 2. Screw
The locked position of the lock lever is adjustable. To
adjust it, remove the screw securing the lock lever. The
lock lever will come o. Set the lock lever at the desired
angle. After adjustment, tighten the lock lever clockwise.
Switch action
► Fig.6: 1. Switch trigger
CAUTION:
• Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the “OFF” position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched o and
unplugged before carrying out any work on the
tool.
10 ENGLISH
Installing or removing the bit
► Fig.7
CAUTION:
• Install the bit securely. Always use only the
wrenches provided with the tool. A loose or
overtightened bit can be dangerous.
• Do not tighten the collet nut without inserting a
bit. It can lead to breakage of the collet cone.
Insert the bit all the way into the collet cone and tighten
the collet nut securely with the two wrenches.
Use the correct size collet cone for the bit which you
intend to use.
To remove the bit, follow the installation procedure in
reverse.
OPERATION
Set the tool base on the workpiece to be cut without
the bit making any contact. Then turn the tool on and
wait until the bit attains full speed. Lower the tool body
and move the tool forward over the workpiece surface,
keeping the tool base ush and advancing smoothly
until the cutting is complete.
When doing edge cutting, the workpiece surface should
be on the left side of the bit in the feed direction.
► Fig.8: 1. Workpiece 2. Bit revolving direction
3. View from the top of the tool 4. Feed
direction
NOTE:
• Moving the tool forward too fast may cause
a poor quality of cut, or damage to the bit or
motor. Moving the tool forward too slowly may
burn and mar the cut. The proper feed rate will
depend on the bit size, the kind of workpiece
and depth of cut. Before beginning the cut on
the actual workpiece, it is advisable to make a
sample cut on a piece of scrap lumber. This will
show exactly how the cut will look as well as
enable you to check dimensions.
• When using the straight guide, be sure to install
it on the right side in the feed direction. This
will help to keep it ush with the side of the
workpiece.
► Fig.9: 1. Feed direction 2. Bit revolving direction
3. Workpiece 4. Straight guide
Straight guide
► Fig.10
The straight guide is eectively used for straight cuts
when chamfering or grooving.
To install the straight guide, insert the guide bars into
the holes in the tool base. Adjust the distance between
the bit and the straight guide. At the desired distance,
tighten the wing bolts to secure the straight guide in
place.
► Fig.11: 1. Guide bar 2. Clamp screw 3. Straight
guide
When cutting, move the tool with the straight guide ush
with the side of the workpiece.
If the distance (A) between the side of the workpiece
and the cutting position is too wide for the straight
guide, or if the side of the workpiece is not straight, the
straight guide cannot be used. In this case, rmly clamp
a straight board to the workpiece and use it as a guide
against the router base. Feed the tool in the direction of
the arrow.
► Fig.12
Templet guide (Accessory)
► Fig.13
The templet guide provides a sleeve through which
the bit passes, allowing use of the tool with templet
patterns.
To install the templet guide, loosen the screws on the
tool base, insert the templet guide and then tighten the
screws.
► Fig.14: 1. Screw 2. Base 3. Template guide
Secure the templet to the workpiece. Place the tool on
the templet and move the tool with the templet guide
sliding along the side of the templet.
► Fig.15: 1. Bit 2. Base 3. Templet 4. Workpiece
5. Distance (X) 6. Outside diameter of the
templet guide 7. Templet guide
NOTE:
• The workpiece will be cut a slightly dierent
size from the templet. Allow for the distance (X)
between the bit and the outside of the templet
guide. The distance (X) can be calculated by
using the following equation:
Distance (X) = (outside diameter of the templet
guide - bit diameter) / 2
Dust nozzle set (Accessory)
► Fig.16: 1. Dust nozzle 2. Thumb screw
Use the dust nozzle for dust extraction. Install the dust
nozzle on the tool base using the thumb screw so that
protrusion on the dust nozzle t to the notch in the tool
base.
Then connect a vacuum cleaner to the dust nozzle.
► Fig.17
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched o and
unplugged before attempting to perform inspec-
tion or maintenance.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
Altri manuali per RP0900
12
Indice
Lingue:
Altri manuali Makita Utensili
Makita
Makita XGC01 Manuale utente
Makita
Makita JR103D Manuale utente
Makita
Makita DCO181 Manuale utente
Makita
Makita HR007G Manuale utente
Makita
Makita DUX18 Manuale utente
Makita
Makita BHR202 Manuale utente
Makita
Makita HM1200 Manuale utente
Makita
Makita HR2652 Manuale utente
Makita
Makita HM1213C Manuale utente
Makita
Makita M2401 Manuale utente
Makita
Makita HR3540C Manuale utente
Makita
Makita DTR180 Manuale utente
Makita
Makita HR007G Manuale utente
Makita
Makita M1902 Manuale utente
Makita
Makita DTM40 Manuale utente
Makita
Makita M8600 Manuale utente
Makita
Makita DGP180 Manuale utente
Makita
Makita HR3011FC Manuale utente
Makita
Makita HR2653 Manuale utente
Makita
Makita DGP180 Manuale utente
