Markusson Combimatic Manuale utente

Original Instruction Manual

Combimatic

Owner’s manual

2 Combimatic_v2_EN_ 210315

Combimatic

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . 3

1.1 Important user information . . . . . . . . . . 3

1.2 About this manual. . . . . . . . . . . . . . .3

1.3 Intended use . . . . . . . . . . . . . . . . . 3

1.4 Regulatory information . . . . . . . . . . . . 3

1.5 Nameplate . . . . . . . . . . . . . . . . . . 4

1.6 Recycling information . . . . . . . . . . . . .4

2 Safety. . . . . . . . . . . . . . . . . . . . 5

2.1 Safety notices . . . . . . . . . . . . . . . . .5

2.2 Safety instructions . . . . . . . . . . . . . . 5

2.3 Signs and symbols . . . . . . . . . . . . . . 6

3 Product Description. . . . . . . . . . . . . 7

3.1 Product overview . . . . . . . . . . . . . . . 7

3.2 Front view . . . . . . . . . . . . . . . . . . .8

3.3 Back view . . . . . . . . . . . . . . . . . . . 9

3.4 Grinding head . . . . . . . . . . . . . . . 10

3.5 Pneumatic chain tensioner . . . . . . . . . 11

3.6 Controls . . . . . . . . . . . . . . . . . . . 12

3.6.1 Grinding speed knob . . . . . . . . 13

3.6.2 Counter . . . . . . . . . . . . . . . 13

3.7 Chain overview . . . . . . . . . . . . . . . 13

3.8 Technical data. . . . . . . . . . . . . . . . 14

4 Installation . . . . . . . . . . . . . . . . . 15

4.1 Safety during installation . . . . . . . . . . 15

4.2 Site requirements . . . . . . . . . . . . . . 15

4.3 Unpack the machine . . . . . . . . . . . . 15

4.4 Assemble the stand . . . . . . . . . . . . . 16

4.5 Assemble the pneumatic chain tensioner . . 17

4.6 Bench-mount the machine . . . . . . . . . 20

4.7 Install and center the grinding wheel . . . . 20

4.8 Test the machine before first use . . . . . . 21

5 Operation . . . . . . . . . . . . . . . . . .22

5.1 Safety during operation . . . . . . . . . . . 22

5.2 Prepare for operation . . . . . . . . . . . . 22

5.2.1 Prepare the grinding wheel . . . . . 22

5.2.2 Set the head-tilt angle . . . . . . . . 23

5.2.3 Set the top-plate angle. . . . . . . . 23

5.2.4 Insert the chain . . . . . . . . . . . 24

5.2.5 Tighten the chain . . . . . . . . . . 25

5.2.6 Set the chain pusher. . . . . . . . . 26

5.2.7 Set the grinding depth . . . . . . . . 28

5.2.8 Set the cutter top plate to equal

lengths . . . . . . . . . . . . . . . . 28

5.2.9 Center the grinding disc . . . . . . . 28

5.2.10 Set the grinding length. . . . . . . . 29

5.2.11 Test the grinding settings . . . . . . 29

5.3 Operate the machine . . . . . . . . . . . . 30

5.4 Depth gauge grinding . . . . . . . . . . . . 32

5.5 Adjust the chain ruler for .404 chain grinding 33

6 Maintenance and Service. . . . . . . . . .34

6.1 Safety during maintenance . . . . . . . . . 34

6.2 Frequency of maintenance . . . . . . . . . 34

6.3 Change the grinding wheel and fit the

grinding wheel guard . . . . . . . . . . . . 35

6.4 Set the depth gauge height . . . . . . . . . 35

6.5 Fasten the chain lock . . . . . . . . . . . . 35

6.6 Check and adjust the wire . . . . . . . . . 36

6.7 Service . . . . . . . . . . . . . . . . . . . 37

7 Troubleshooting. . . . . . . . . . . . . . .38

7.1 Troubleshooting procedure . . . . . . . . . 38

7.2 Sharpening test . . . . . . . . . . . . . . . 38

7.3 Issues . . . . . . . . . . . . . . . . . . . . 39

7.4 Troubleshooting indicators . . . . . . . . . 40

8 Accessories and Spare Parts. . . . . . . .41

8.1 Ordering information . . . . . . . . . . . . 41

8.2 List of accessories . . . . . . . . . . . . . 41

8.3 Converter . . . . . . . . . . . . . . . . . . 45

9 Declaration of conformity . . . . . . . . . .46

Combimatic_v2_EN_210315 3

Combimatic Introduction

1 Introduction

1.1 Important user information

WARNING Before you install, operate or do maintenance on the machine, you must read the safety information

in this manual. Obey the instructions in this manual to prevent injuries or damage to the equipment.

1.2 About this manual

This user manual describes how to safely install, operate, and perform basic maintenance on the product. This

manual also describes the parts of the machine, and it shows different accessories and spare parts that are

available.

1.3 Intended use

The machine must only be used to sharpen the cutting chains used on power saws, forestry machines and

harvesters. It automatically sharpens the cutting teeth and depth gauges on chains. The machine is designed for

indoor use only.

Unintended use

The machine must not be used outdoors or in a manner that is not described in this manual.

1.4 Regulatory information

Regulations are given below. A copy of the EC Declaration of conformity is supplied with the machine.

WARNING Before you install, operate or do maintenance on the machine, you must read the safety information

in this manual. Obey the instructions in this manual to prevent injuries or damage to the equipment.

Directive/standard Description

2006/42/EC The Machinery Directive (MD)

2014/35/EU The Low-Voltage Directive (LVD)

2014/30/EU The Electro Magnetic Compatibility Directive (EMC)

EN-ISO:12100:2010 Safety of machinery – Basic components, general principles for design

EN 60204-1:2006 Safety of machinery – Electrical equipment of machines

– Part 1: General requirements

EN 61000-6-3:2007 Emission standard for residential, commercial and light-industrial

environments

EN 55014-1:2017,

EN 55014-2: 2015

Electromagnetic compatibility – Requirements for household

appliances, electric tools and similar apparatus

– Part 1: Emission

– Part 2: Immunity

4 Combimatic_v2_EN_ 210315

Combimatic

Introduction

1.5 Nameplate

This nameplate is placed on the machines grinding head.

1.6 Recycling information

This symbol shows that electrical and electronic equipment must not be disposed of as unsorted municipal waste. It

must be collected separately. Recycle according to current local rules and regulations.

762 31 Rimbo, Sweden

Model: Combimatic

Mfg: 2016-43 Weight: 48 kg

Auto Chain Grinder

Input: 12V DC 12A, no: 3250rpm

Arbor: Ø 16mm

S/N: 12345 Made in Sweden

Combimatic_v2_EN_210315 5

Combimatic Safety

2 Safety

2.1 Safety notices

This section contains safety information for the power tool. This manual contains WARNINGS, CAUTIONS and

IMPORTANT notes that are applicable for the safe operation of the power tool.

WARNING A warning tells you about conditions that can cause injury or death, if you do not obey the

instructions. Do not continue until all conditions are accepted and engaged.

CAUTION A caution tells you about conditions that can cause damage to equipment, if you do not obey the

instructions. Do not continue until all conditions are accepted and engaged.

IMPORTANT Important or noteworthy information that enables trouble-free and optimal use of the power tool.

2.2 Safety instructions

WARNING Before you install, operate or do maintenance on the power tool, you must read the safety

information in this manual. Obey the instructions in this manual to prevent injuries or damage to the equipment.

WARNING Read all safety warnings, instructions, illustrations, and specifications provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. Save all warnings

and instructions for future reference.

WARNING Put the power tool indoors, in a dry area with good light and a flat and level floor. Do not let the

machine become wet or moist. Do not put the power tool near gas, liquids or other materials that can catch fire or

explode.

WARNING Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

WARNING The power tool must always be fixed to the floor. Make sure that it is safely attached.

WARNING Do not operate the power tool in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust, or near flammable materials. Power tools create sparks which may ignite such materials.

WARNING The user must only do maintenance that is described in this manual on the power tool. Only

approved and trained service technicians can do service on the power tool.

WARNING Make sure that the power is turned off before you install, operate or perform maintenance on the

power tool.

WARNING If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

WARNING To prevent mistakes when chains are sharpened, it is very important to understand how the grinding

machine works. Read the instructions carefully before the power tool is used.

WARNING Use protective glasses – risk of sparks from the power tool when grinding.

WARNING Use ear protection – risk of hearing damage.

WARNING Use safety gloves – risk of cuts from the grinding disc or chain.

WARNING Be careful around moving parts – risk of squeezing.

WARNING Stop the power tool immediately if it does not work correctly!

WARNING Before a chain is sharpened, make sure that the the grinding disc is not cracked, does not vibrate or

wobble. If the grinding disc is damaged it must be replaced immediately, see section 6.3, “Change the grinding wheel

and fit the grinding wheel guard”. If abnormal vibrations occur during operation, immediately stop the power tool and

check the condition of the grinding disc.

WARNING Attach air hoses and cables with cable clamps, to make sure no one trips over them.

WARNING The supply cord can only be replaced by the manufacturer, or approved and trained service

technicians in order to avoid a safety hazard.

6 Combimatic_v2_EN_ 210315

Combimatic

Safety

CAUTION Only use accessories that are supplied or approved by the manufacturer.

CAUTION If the pitch is not correctly set the chain will be pushed into an incorrect sharpening position. This

may result in a damaged chain.

CAUTION If the metal of a cutting link turns blue during grinding, the speed is set too high and the metal is

overheated. This can cause the metal in the cutting tooth to lose its properties. Replace the damaged cutting link or

sharpen the chain again.

CAUTION It is recommended that the tool is always supplied via a residual current device having a rate

residual current of 30 mA or less.

CAUTION Clean the power tool. To prevent that it breaks, remove grinding dust every day. Use a vacuum

cleaner, brush or similar to clean the machine.

2.3 Signs and symbols

See the table below for information about the signs and symbols on the product:

Sign/Symbol Description

Warning! A warning tells you about conditions that can cause injury or death, if you do not obey the

instructions. Do not continue until all conditions are accepted and engaged.

Risk for cutting injuries. Keep fingers away from the area when the machine is on.

Risk for pinching injuries. Keep fingers away from the area when the machine is on.

Before you install, operate or do maintenance on the machine, you must read the safety information

in the User manual. Obey the instructions to prevent injuries or damage to the equipment.

Always wear protective gloves when using the machine.

Always wear protective glasses and ear protection when using the machine.

Combimatic_v2_EN_210315 7

Combimatic Product Description

3 Product Description

3.1 Product overview

The Combimatic Auto Chain Grinder is a machine that sharpens chains. The machine can sharpen chains (3/4″

and .404” pitch) for power saws, forestry machines, and harvesters. A pneumatic chain tensioner is attached to the

stand. It secures and tensions the chain when it is sharpened. The stand has 2 chain hangers, which makes it easier

to separate the sharpened chains from chains that are not yet sharpened. Accessories are availabe for extra long

chains.

8 Combimatic_v2_EN_ 210315

Combimatic

Product Description

3.2 Front view

Pos Part Description

AGrinding Head Holds the grinding wheel in its correct position.

BCounter Sets the number of cutters to be sharpened. See section 3.6.1,

“Counter”.

CControl panel The controls starts and stops the different functions of the machine.

See section 3.6, “Controls” for further information.

DChain hangers Hangers on both sides for unsharpened or sharpened chains..

EStand Holds the machine

FPneumatic chain tensioner Secures the chain in the correct position.

GGrinding wheel The wheel that sharpens the chain.

HGrinding wheel centering knob Centers the grinding wheel above the chain.

IGrinding depth knob Sets the grinding depth for the gullets

JChain pusher adjustment knob Sets the grinding length.

KPower Supply cable Supplies electricity to the machine.

LChain pusher Advances the chain through the vise.

MChain vise Positions the chain as it moves in the machine.

NLeft-right alignment screw Sets the right and left cutters to equal length.

OTop-plate angle screw Sets the top-plate angle, 0-35°. Default 30°.

KLMNO

Combimatic_v2_EN_210315 9

Combimatic Product Description

3.3 Back view

Pos Part Description

APitch adjustment wing Makes an approximate setting for the pitch.

BGrinding head cover and grinding

wheel guard

Protects the grinding head and grinding wheel; it also protects the

user from sparks during grinding.

CTop-plate angle scale Shows the top-plate angle on a scale from 0-35°. Default: 30°. It is

set using the top-plate angle screw (O in Front view illustration).

DHead-tilt angle scale Shows the head-tilt angle on a scale from 50-90°.

Default: 60°.

EWire Controls the vertical movement of the grinding head.

FWire adjustment nuts Adjusts the wire that controls the vertical movement of the grinding

head.

GHead-tilt angle nut Sets the head-tilt angle on the head-tilt angle scale. (D)

10 Combimatic_v2_EN_ 210315

Combimatic

Product Description

3.4 Grinding head

The grinding wheel on the grinding head sharpens the chains. The type of wheel, the top-plate angles, the settings of

the grinding head, and the profiling of the grinding wheel all determine how the chain is sharpened.

Pos Part Description

AGrinding wheel Grinds the chain.

BGrinding wheel nut Keeps the grinding wheel in place.

CGrinding wheel guard Protects the user and grinding wheel when the chain is sharpened.

DAttachment knobs Secures the grinding wheel guard in place.

Altri manuali per Combimatic

Indice

Altri manuali Markusson Utensili

Markusson

Markusson Combimatic Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare