Montipower BRISTLE BLASTER Manuale utente

BRISTLE

BLASTER®

ELECTRIC DOUBLE

Overview Figure 1

1 Power cable

2 Air inlet

3 Safety Switch

4 Vibration damping handle

5 Safety hook

6 Protective Cap

7 Accelerator Bar

8 Spindle

9 Torx wrench

Figure 1

EN Operating instructions

Dear customer!

MontiPower®thanks you for the purchase of one of its products and invites you to read these

operating instructions, which contain all the necessary information for the correct use of the

tool. Please read these instructions carefully and follow the information contained herein.

Please maintain the manual in good condition and keep it with the tool at all times. The

contents of this manual may be changed without notice and without the implication of any

additional obligations. It is prohibted to copy or translate any part of this manual without the

prior written consent of the manufacturer.

Original instructions

1. Declaration of Conformity

We declare under our sole responsibility the Bristle Blaster®, identified by type and serial

number *1), comply with all relevant requirements of EU Directives *2) and standards *3)

2. Specified Use

The machines, with original MontiPower®accessories, are intended for use in surface

preparation, simultaneously cleaning and creating an achor profile.

The user bears sole responsibility for any damage caused by improper use. Generally

accepted accident prevention regulations and the enclosed safety information must be

observed.

Specications Value Unit

Weight 2.2 kg I 4.9 lbs

Belt diameter (outer) 110 mm

Output 910 W

Idle speed (±5%) 2,300 rpm

Vibration 4 m/sec2

Sound pressure level < 80 dB(A)

*2) 2014/30/EU, 2006/42/EC, 2011/65/EU

*3) EN 60745-1:2009+A11:2010, EN 60745-2-3:2011+A2:2013+A11:2014+A12:2014

Technical Data: Bristle Blaster®Electric (*1) Serial number)

These technical specifications apply equally to the 110 V - 240 V versions, whether these

versions are 50 Hz or 60 Hz.

BRISTLE BLASTER®ELECTRIC DOUBLE

3. General Safety Instructions

For your own protection and for the protection of your electrical tool, pay attention

to all parts of the text that are marked with this symbol!

WARNING - Reading the operating instructions will reduce the risk of injury.

Keep all safety instructions and information for future reference. Ensure that these

documents are kept with the electrical tool at all times.

4. Special Safety Instructions

4.1 Safety Warnings Common for the use of Rotary Impact Tool Operations:

a) This power tool is intended to function as a Rotary Impact Tool. Read all safety

warnings, instructions, illustrations and specifications provided with this power tool.

Failure to follow instructions may result in electric shock, fire and/or serious injury.

b) Only Rotary Impact Surface Preparation / Bristle Blasting operations shall be

performed with this power tool. Operations for which the power tool was not

designed may create a hazard and cause personal injury.

c. Only use MontiPower®Bristle Blaster®Belts and MontiPower®Adaptor Systems with

this tool. Do not use accessories which are not specifically designed and

recommended by the tool manufacturer. Just because the accessory can be

attached to your power tool does not assure safe operation.

d) Do not use a damaged Bristle Blaster®Belt or Adaptor System, inspect before use.

e) After replacement of the Bristle Blaster®Belt, check Adapter System for correct

assembly.

f) After fitting accessories such as the Adapter System and Bristle Blaster®Belt, always

remove Allen key / Torx wrench. Always ensure the Allen key / Torx wrench is

removed prior to switching on the tool.

g) When placing the tool on a bench or on the floor, the label must always point

upward.

h) When not in use, disconnect the tool from the power supply and store in a suitable,

dry place to prevent unintentional or unauthorised use.

i) Always hold the tool by the body and the vertical handle when in operation.

j) Use Bristle Blaster®Belt in the correct operating direction (Figure 3).

k) The Bristle Blaster®Belt can produce sparks when machining hard surfaces.

l) If the tool suddenly feels different (level of vibration) or produces a different noise

(pitch), the tool should be shut down immediately and the accessories such as the

Adapter System, Bristle Blaster®Belt checked for damage.

m) Wear personal protective equipment. Always use a face shield,

safety goggles or safety glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable of stopping flying debris

generated by operations. The dust mask or respirator must be capable of filtering

particles generated by your operation. Prolonged exposure to high intensity noise

WARNING - Read all safety warnings and instructions. Failure to follow all safety

warnings and instructions may result in electric shock, fire and/or serious injury.

BRISTLE BLASTER®ELECTRIC DOUBLE

EN Operating instructions

may cause hearing loss.

n) Keep bystanders a safe distance away from work area. Anyone entering the work

area must wear personal protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond the immediate area of

operation.

o) Hold power tool by insulated gripping surfaces only when performing an operation

where the Bristle Blaster®Belt may contact hidden wiring or its own cord. The Bristle

Blaster®Belt contacting a "live" wire may make exposed metal parts of the power

tool "live" and could cause an electric shock.

p) Never lay the power tool down until the accessory has come to a complete stop. The

spinning accessory may grab the surface and pull the power tool out of your control.

q) Do not run the power tool while carrying it at your side. Accidental contact with the

spinning Bristle Blaster®Belt could snag your clothing, pulling the accessory into your

body.

r) Regularly clean the power tool’s air vents (Figure 2). The motor’s fan will draw the

dust inside the housing and excessive accumulation of powdered metal may cause

electrical hazards. The air vent cap may be removed for cleaning, use non-metallic

objects only.

s) Do not operate the power tool near flammable materials. Sparks could ignite these

materials.

t) Do not use any liquid coolants. Using water or other liquid coolants may result in

electrocution or shock.

4.2 Kickback and Related Warnings

Kickback is a sudden reaction to a rotating wheel which can cause rapid stalling of

the rotating Bristle Blaster®Belt which in turn causes the uncontrolled power tool to

be forced in the direction opposite of the Bristle Blaster®Belt’s rotation.

a) Maintain a firm grip on the power tool and position your body and arm to allow you

to resist kickback forces. Use auxiliary handle, if provided, for maximum control

over kickback or torque reaction during start-up. The operator can control torque

reactions or kickback forces if proper precautions are taken.

b) Never place your hand near the rotating Bristle Blaster®Belt. Accessory may

kickback over your hand.

c) Do not position your body in the area where power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the Bristle Blaster®Belt’s

movement at the point of snagging.

d) Use special care when working corners, sharp edges etc. Avoid bouncing and

snagging the Bristle Blaster®Belt. Corners, sharp edges or bouncing have a tendency

to snag the rotating Bristle Blaster®Belt and cause loss of control or kickback,

damage to the Bristle Blaster®Belt and even breakage of the tooth belt.

e) Do not attach any other belt or belt Adaptor System than that provided by the

manufacturer.

BRISTLE BLASTER®ELECTRIC DOUBLE

Figure 2

Figure 3

Figure 4

BRISTLE BLASTER®ELECTRIC DOUBLE

EN Operating instructions

4.3 Additional Safety Instructions

WARNING – Always wear protective goggles.

• Accessories must be stored and handled with care in accordance with the

manufacturer's instructions.

• The workpiece must lay flat and be secured against slipping, e.g. using clamps.

Large workpieces must be sufficiently supported.

• We recommend connecting a residual current circuit-breaker (FI) upstream.

When the tool is shut down via the FI circuit-breaker, it must be checked and

cleaned. See Chapter 9 for more information on cleaning the motor.

• Damaged, eccentric or vibrating tools must not be used.

• Disconnect the tool from the mains power supply before making any

adjustments, converting or servicing the machine.

• A damaged or cracked handle must be replaced. Never operate a machine

with a defective handle.

• A damaged or cracked hand guard must be replaced. Never operate a machine

with a defective protective cap.

Reducing dust exposure:

WARNING -Depending on the surface to be trearted, some dust created by the

MontiPower®Bristle Blasting®process may contain chemicals known to cause

cancer, birth defects or other reproductive harm. Examples of such chemicals

could include:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies depending on how often you do this type of work.

To reduce your exposure to these chemicals work in a well ventilated area, and work with

approved safety equipment, such as dust masks that are specially designed to filter out

microscopic particles.

This also applies to dust from other materials such as some timber types (like oak or

beech dust), metals and asbestos. It may also lead to allergic reactions and respiratory

disease. Do not let dust enter the body.

Observe the relevant guidelines and national regulations for your material, staff,

application and place of application (e.g. occupational health and safety regulations,

disposal).

Collect the particles generated at the source and avoid deposits in the surrounding area.

Use suitable accessories for special work to ensure fewer particles enter the environment

in an uncontrolled manner.

Reduce dust exposure with the following measures:

• do not direct the escaping particles and the exhaust air stream at yourself or nearby

persons or on dust deposits,

• use an extraction unit and/or air purifiers,

BRISTLE BLASTER®ELECTRIC DOUBLE

5. Initial Operation

Before plugging in, check that the rated mains voltage and mains frequency, as

stated on the rating label, match with your power supply.

Always install an RCD with a max. trip current of 30 mA upstream.

5.1 Attaching the Vibration Damping handle

Always work with the vibration damping handle (4) attached! Attach the handle on

the top or bottom side of the machine, depending on working position, and secure.

See Figure 5.

• ensure good ventilation of the workplace and keep clean using a vacuum cleaner as

sweeping or blowing stirs up dust.

• vacuum or wash protective clothing. Do not blow, beat or brush.

5.2 Attaching the Protective Cap

Always work with the Protective Cap (6) attached.

Figure 5

Installing:

Slide the Protective Cap (6) over the cams on the front end as shown below and secure by

tightening the screw on the side.

Figure 6

BRISTLE BLASTER®ELECTRIC DOUBLE

EN Operating instructions

6. Fitting the Adaptor System & Bristle Blaster®Belt

Disconnect the battery from the unit before changing the belt or Adaptor System.

The machine must be switched off and the spindle at a standstill.

6.1 Positioning the accessory

See Figure 7.

a) Fasten Bristle Blaster®Belt correctly to the tool using the MontiPower®

Adapter System (pay attention to rotation direction) and serrated lock washer and

screw. Ensure the Bristle Blaster®Belt adaptors are in an offset position from each

other.

b) For Bristle Blaster®stainless steel belts, use only the stainless steel Accelerator Bar.

c) Before plugging in to operate the tool, you must check that it is possible to actuate

the Safety Switch correctly and that the switch returns to the "OFF" position

when you release the pressure on the Safety Switch.

d) To start the tool, release the safety clip by pushing it backwards and push

the Safety Switch (Figure 8).

Figure 7

Figure 8

BRISTLE BLASTER®ELECTRIC DOUBLE

Altri manuali per BRISTLE BLASTER

Indice

Lingue:

Altri manuali Montipower Utensili

Montipower

Montipower MBX Electric Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare