Panduit MEHT Manuale utente
© Panduit Corp. 2006
PA24578A01
Rev. 04 7-2006
METAL EMBOSSING HAND TOOL
OPERATION INSTRUCTIONS
For Technical Support:
888-506-5400, ext. 3255
Fax: 630-759-7532
Website: www.panduit.com
E-mail: [email protected]
MEHT
A. Tape cassette door
B. Tape rollers
C. Tape advance knob
D. Start line
E. Tape pawl
F. Embossing handle
G. Embossing wheel
H. Character selection window
I. Cutting handle
J. Embossing adjustment screw
K. Cable tie slot entrance
L. Tape exit/Cutting assembly
M. Trailer length guide
MEHT
OPERATION INSTRUCTIONS
Page: 1 of 14
MEHT
OPERATION INSTRUCTIONS
Page: 2 of 14
About Your New Labelmaker
With your new
PANDUIT
MEHT labelmaker,
you can create a wide variety of aluminum and
stainless steel labels. The labelmaker uses
1/2" (12 mm) label tape. Aluminum and
stainless steel tapes are available as follows:
•META-X: 1/2" x 16 ft. (12.6mm x 4.9m)
aluminum tape
•METS4-X: 1/2" x 21 ft. (12.6mm x 6.4m)
304 grade stainless steel tape
•METS3-X: 1/2" x 21 ft. (12.6mm x 6.4m)
316 grade stainless steel tape
You can also use a Reverse Image Wheel with
the
PANDUIT
MEHT labelmaker. This wheel
allows you to print mirror script labels that
meet special requirements in the industry.
Mirror labels are used on moulds or casts for
metal or rubber injection, silicon casting, fiber
glass applications, and so on.
Visit www.panduit.com for information on
obtaining tapes and accessories for your label-
maker.
MEHT
OPERATION INSTRUCTIONS
Page: 3 of 14
Loading the Label Tape
The
PANDUIT
MEHT is set to emboss non-
adhesive aluminum or stainless steel tape.
To load the tape roll
1. Hold the labelmaker in your left hand.
2. Open tape door (A).
3. Insert roll of tape allowing the end to
extend about 2" (5 cm) through the tape
slot.
4. Close the tape door.
5. Feed the tape between the two rollers (B).
6. Squeeze the embossing handle (F) half-
way (one click) several times to ensure
the tape is inserted all the way.
F
A
B
Cutting the Tape
To cut the tape
1. Squeeze the embossing handle half-way,
several times until the tape extends from
the front of the cutting assembly (M) by at
least 1" (2.5cm).
Note: Before cutting the tape, make
sure the end of the tape extends
beyond the edge of the cutting
assembly so you can easily pull the
label out. Otherwise, a tape jam may
occur.
2. Lift the cutting handle (I) gently until it is
vertical to cut the tape.
Page: 4 of 14
MEHT
OPERATION INSTRUCTIONS
MEHT
OPERATION INSTRUCTIONS
Page: 5 of 14
Embossing the Label
Avoid turning the embossing wheel at
the same time you are squeezing the
embossing handle. This can damage
the character wheel.
To emboss a label
1. Turn the character selection wheel (G)
until the desired letter is centered in the
window (H).
2. Squeeze the embossing handle (F) firmly.
3. Release the embossing handle fully
before selecting the next character.
To add space between words
•Squeeze embossing handle (F) half-way
(one click) or turn the tape advance knob
clockwise (one click per space).
MEHT
OPERATION INSTRUCTIONS
Page: 6 of 14
Embossing on Stainless Steel Tape
You may need to adjust the labelmaker to
emboss properly when using stainless steel
tape.
To adjust for stainless steel tape
1. Turn the adjustment screw (J) clockwise
1/2 to 3/4 turn.
2. Emboss the text as described in
"Embossing the Label" on page 5. When
you return to using aluminum tape, you
may need to reverse this adjustment.
Retracting the Tape
You may want to retract the tape, for example,
if the tape advanced too far or to center the
text on the label.
To retract the tape
1. Pull back the pawl (E).
2. Turn the tape advance knob (C) counter-
clockwise.
MEHT
OPERATION INSTRUCTIONS
Page: 7 of 14
Removing the Tape
To remove the tape
1. Retract the tape as described in
"Retracting the Tape" on page 7.
2. Open the tape cassette door (A) and
remove the tape.
Use caution when removing stainless
steel tape that may have sharp
edges.
3. Reload the tape as described in "Loading
the Label Tape" on page 3.
Page: 8 of 14
MEHT
OPERATION INSTRUCTIONS
A
Centering the Text on the Label
The leader/trailer length guide (M) has
positioning marks for a short (S) or long label
(L). Use the marks on the guide to center the
text on your label.
To center the text on a long label
1. After cutting the previous label, emboss
the text on a new label.
2. Pull the leader/trailer length guide (M) to
the forward position.
3. Advance the tape until the last embossed
letter is opposite the L on the guide. The
label has a leader/trailer of approximately
2" (5 cm) and the text is centered.
4. Lift the cutting handle (I) to the vertical
position to cut the tape.
MEHT
OPERATION INSTRUCTIONS
Page: 9 of 14
M
Altri manuali Panduit Utensili
Panduit
Panduit PAT1M Manuale utente
Panduit
Panduit BT75SDT Manuale utente
Panduit
Panduit CT-3001/CCP Manuale utente
Panduit
Panduit PATMBM4.0 Manuale utente
Panduit
Panduit CT-3001 Manuale utente
Panduit
Panduit CT-980 Manuale utente
Panduit
Panduit PPTMT Manuale utente
Panduit
Panduit GS2B Manuale utente
Panduit
Panduit CT-1550 Manuale utente
Panduit
Panduit CT-930 Manuale utente
Panduit
Panduit ST2MT Manuale utente
Panduit
Panduit GS4MT Manuale utente
Panduit
Panduit GS4EH Manuale utente
Panduit
Panduit PAT1M4.0 Manuale utente
Panduit
Panduit BlackFin CT-2600 Series Manuale utente
Panduit
Panduit BlackFin CT-2940/STBT Manuale utente
Panduit
Panduit PTS Manuale utente
Panduit
Panduit TGJT Manuale utente
Panduit
Panduit GS4EH Manuale utente
Panduit
Panduit GTS Manuale utente
