Planet IGS-1020TF Manuale utente

Industrial 8-Port 10/100/1000BASE-T

+ 2-Port 100/1000BASE-X SFP Ethernet Switch

IGS-1020TF

User’s Manual

Table Of Contents

1. Package Contents ............................................................. 3

2. Hardware Introduction ...................................................... 4

2.1 Physical Dimensions ................................................ 4

2.2 Switch Front Panel................................................... 5

2.3 LED Indicators ........................................................ 6

2.4 Switch Upper Panel ................................................. 8

2.5 Wiring the Power Inputs .......................................... 8

2.6 Wiring the Fault Alarm Contact ............................... 10

2.7 ProductSpecications ............................................ 10

3. Installation..................................................................... 14

3.1 DIN-rail Mounting Installation ................................. 14

3.2 Wall-mount Plate Mounting..................................... 16

3.3 Installing the SFP Transceiver ................................. 17

3.4 Removing the Transceiver Module ........................... 19

4. Troubleshooting .............................................................. 20

APPENDIX A: Networking Connection.................................... 21

A.1 Switch’s RJ45 Pin Assignments................................... 21

A.2 RJ45 Cable Pin Assignments ...................................... 22

A.3 Fiber Optic Cable Connection Parameter ..................... 23

APPENDIX B: Approved PLANET SFP Transceivers .................. 25

1.Package Contents

Thank you for purchasing PLANET industrial 10-port Gigabit

Ethernet Switch, IGS-1020TF. In the following section, the term

“Industrial Gigabit Ethernet Switch” means the IGS-1020TF.

Open the box of the Industrial Gigabit Ethernet Switch and

carefully unpack it. The box should contain the following items:

Industrial Gigabit Ethernet Switch x 1 User’s Manual x 1

Wall-mount Kit x DIN Rail Kit x 1

If any of these are missing or damaged, please contact your

dealer immediately; if possible, retain the carton including the

original packing material, and use them again to repack the

product in case there is a need to return it to us for repair.

2.Hardware Introduction

2.1 Physical Dimensions

IGS-1020TF Industrial Gigabit Ethernet Switch dimensions (W

x D x H): 135 x 87.8 x 50mm

Side View

Bottom View Front View

Mounting Kit

DIN-Rail Kit

Dimensions ( unit = mm )

Top View Rear View

Input

DC12~48V, AC 24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

1 2 3 4 5 6

100/1000X SFP

109

P1 P2 FAULT

9 10

IGS-1020TF

ACT

1000 LNK

LNK

10/100

100

ACT

1000

LNK

2.2 Switch Front Panel

The front panel of the Industrial Gigabit Ethernet Switch consists

of 8 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports and

2 dual speed 100/1000BASE-X SFP slots. The LED Indicators

are also located on the RJ45 ports and SFP slots of the Gigabit

Ethernet Switch.

Figure 2-1 shows the front panel of Industrial Gigabit Ethernet

Switch.

100/1000X SFP

109

P1 P2 FAULT

9 10

IGS-1020TF

ACT

1000 LNK

LNK

10/100

100

ACT

1000

LNK

Figure 2-1: IGS-1020TF Front Panel

Gigabit TP Interface

10/100/1000BASE-T Copper, RJ45 Twisted-pair: Up to 100

meters.

SFP Slot

100/1000BASE-X mini-GBIC slot, SFP (Small-form Factor

Pluggable) transceiver module: From 550 meters to 2km

(multi-mode ber) and 10/20/30/40/50/70/120 kilometers

(single-modeber).

2.3 LED Indicators

System

LED Color Function

P1 Green Lit: indicates power 1 has power.

P2 Green Lit: indicates power 2 has power.

FAULT Red Lit: indicates either power 1 or power 2 has

no power.

Per 10/100/1000T Port

LED Color Function

100

LNK/ACT Orange

Lit: indicates the link through that port is

successfully established at 100Mbps

or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 1000Mbps.

1000

LNK/ACT Green

Lit: indicates the link through that port is

successfully established at 1000Mbps

or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 100Mbps.

Per 100 / 1000X SFP Slot

LED Color Function

100

LNK/ACT Orange

Lit: indicates the link through that port is

successfully established at 100Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 1000Mbps.

1000

LNK/ACT Green

Lit: indicates the link through that port is

successfully established at 1000Mbps

or 10Mbps.

Blinking: indicates that the Switch is

actively sending or receiving data

over that port.

Off: indicates the link through that port is

successfully established at 100Mbps.

2.4 Switch Upper Panel

The upper panel of the Industrial Gigabit Ethernet Switch

consists of one terminal block connector within two DC power

inputs,

Figure 2-2 shows the upper panel of the Industrial Gigabit

Ethernet Switch.

Input

DC12~48V, AC 24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

1 2 3 4 5 6

Figure 2-2: Industrial Gigabit Ethernet Switch Upper Panel

2.5 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial Gigabit Ethernet Switch is used for two DC redundant

power inputs. Please follow the steps below to insert the power

wire.

When performing any of the procedures like

inserting the wires or tightening the wire-clamp

screws, make sure the power is OFF to prevent

from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1

and 2 for POWER 1, or 5 and 6 for POWER 2.

Input

DC12~48V, AC 24V

V1+ V1- V2+ V2-

PWR1 PWR2Fault

1 2 3 4 5 6

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

Note

1. The wire gauge for the terminal block should be

in the range between 12 and 24 AWG.

2. The DC power input range is 12V ~ 48V DC.

2.6 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. Inserting the wires, the

Industrial Gigabit Ethernet Switch will detect the fault status of

the power failure and then forms an open circuit. The following

illustration shows an application example for wiring the fault

alarm contacts.

123456

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be

in the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 30V, max. 3A

currents.

2.7 ProductSpecications

Model IGS-1020TF

HardwareSpecications

Copper Ports 8 x 10/100/1000BASE-T RJ45 TP

Auto-MDI/MDI-X, auto-negotiation

Indice

Altri manuali Planet Interruttore

Planet

Planet SGSD-1022 Manuale utente

Planet

Planet KVM-800 Manuale utente

Planet

Planet SGSD-1022 Manuale utente

Planet

Planet IGS-6325-4T2X Manuale utente

Planet

Planet GS-5220-16S8C Manuale utente

Planet

Planet FNSW-4800 Manuale utente

Planet

Planet WGSW-24000 Manuale utente

Planet

Planet GSW-4804SF Manuale utente

Planet

Planet SGSW-24040 Manuale utente

Planet

Planet POE-2400G Manuale utente

Planet

Planet FGSW-2620CS Manuale utente

Planet

Planet GS-4210-8P2T2S Manuale utente

Planet

Planet GS-5220-8UP2T2X Manuale utente

Planet

Planet WSW-2401 Manuale utente

Planet

Planet POE-1200G Manuale utente

Planet

Planet VC-810S Manuale utente

Planet

Planet IPOE-270 Manuale utente

Planet

Planet IGS-504HPT Manuale utente

Planet

Planet GS-5220-24T4XVR Manuale utente

Planet

Planet KVM-200 Manuale utente

Planet

Planet GSD-805 Manuale utente

Planet

Planet ISW-500 Manuale utente

Planet

Planet XDL-2420R Manuale utente

Planet

Planet GSD-Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente