FB-1601/1602 Fiber Cleaver User Manual
Thanks for purchasing Pro’sKit FB-1601/1602 Fiber Cleaver. The fixture of product
configuration is three in one fixture for single fiber Ø 250μm & Ø 900μm or 3x2mm drop
cable. Please read the instructions carefully before using the product.
This product has been designed and manufactured to assure personal safety.
Improper use can result in body injury and serious damage to fiber cleaver.
Please read and observe all warning instructions given in this operation manual.
1. Do not disassemble or lubricate any parts of cleaver. Doing so could cause serious
damage to the cleaver.
2. The FB-1601/1602 is a precision tool. Do not impact the cleaver by hitting or dropping it.
Doing so may cause personal injury and loss of cleaving performance.
3. Glass fiber fragments are extremely sharp. Handel with care. Wear safety glasses at all
time during cleaving operation for protection from glass fiber.
4. Dispose of glass fiber fragments properly.
5. The blade of cleaver is extremely sharp. Do not touch it with bare hands.
6. Do not impact the Clamp Cover. Doing so could cause damage to cleaver and loss of
cleaver performance.
7. If cleaver is damage or problem occurs, please contact our maintenance service center.
SPECIFICATION
Fiber Count Coating Diameter
Single fiber Ø250μm & Ø 900μm /3x2mm
Drop cable
Cleaver Blade (5FB-1602-BLADE)
VFL (#FB-1602 only)：
2.5mm Universal Connector
TSTRUCTURE
(#FB-1602 only)
Indicator will light up green while charging; it will turn off when charging completes.
OPERATION PROCEDURE
1. Open the clamp cover and fiber holder lid. Please make sure the blade carriage should
slide forward automatically.
2. Insert the fiber cable into the correct groove with the end of the fiber coating.
3. Close the fiber holder lid and clamp cover.
4. Slide the blade carriage to rear side of the cleaver. The fiber will be cleaved.
5. Open the clamp cover; then open the fiber holder lid and lift the newly cleaver fiber. Lift
the off-cut and dispose it properly.
CLEAN
1. After cutting, please clean the broken fiber. Clean the dirt on the fiberboard with cotton
stick that dipped in alcohol. Do not use acetone or corrosive solvent to clean the
fiberboard. Do not damage the blade for future use.
2. Clean the dirt on the fiberboard regularly with cotton stick that dipped in alcohol. Do not
use acetone or corrosive solvent to clean the fiberboard
CAUTION
Do not rotate the blade with hands.
Do not rotate the blade with metallic tweezers. Doing so may damage the
blade.
BLADE REPLACEMENT AND ADJUSTMENT
A. Adjust the blade (rotate according to 0.1... 23 points indicated on the blade)
First of all, the screw driver will loosen the screw on the blade, use the cotton swab to rotate
the blade to adjust the position of the blade, rotate one face at a time, and the rotation
mode is indicated by the arrow
B. Adjust blade height
1. Loosen the two phillips screws shown in the figure
2. Adjust the screw as shown and adjust the blade height
3. Lock the loosened screws
C. Blade replacement
1. Unscrew the blade setscrew. (circle mark)
2. Remove the blade with tweezers.
TROUBLESHOOTING
If there is a problem with the cutter, it may be due to the following reasons
The optical fiber is placed askew
Make sure that the optical fiber is straight
into the cutter slot holder
Dirty optical fiber pressure pad
Clean optical fiber pressure pad
Remove and clean the fiber
Remove and clean the fiber
VFL (FB-1602 only) has problems, which may be caused by the following reasons
VFL does not work or Glint mode is not
available
The battery is dead or low battery. Charge
it in time
Port coupling porcelain tube damaged
Replace the porcelain tube
FB-1601/1602 光纖切割刀使用說明
感謝您購買 Pro’sKit FB-1601/1602 精密光纖切割刀，本產品配置的夾具為三合一夾具，
適合 Ø 250μm 及 Ø 900μm 裸光纖以及 3x2mm 皮線光纖使用。使用前請仔細閱讀說明書，
閱讀後請妥善保存，以備查閱。
使用方法和安全操作規則
1. 請不要自行拆解本產品，以免造成產品損壞.
2. FB-1601/1602 為精密工具。不要撞擊或掉落切割刀。否則可能會導致人身傷害和切割性
能下降。
3.光纖碎片非常鋒利,切割操作期間始終戴安全眼鏡，並請妥善處理光纖碎片，以避免受傷。
4.切割器的刀刃非常鋒利,不要徒手觸摸。
5.不要撞擊夾蓋,這樣做可能會損壞切割刀並降低切割性能。
6.如果切割刀損壞或出現問題，請聯繫我們的維修服務中心
規格
Ø250μm & Ø900μm,3x2mm 皮線光纖
鐳射光纖測試 VFL (僅FB-1602)：
產品說明
（#鐳射光纖測試功能，僅 FB-1602 適用）
充電時綠色指示燈恆亮，充滿後熄滅。
操作步驟
1.打開壓線板及蓋板，切割刀導軌會自動推至前端（如圖）
2.將剝除好塗覆層的裸光纖放置於夾具內（Ø250μm / Ø900μm/ 3x2 皮線）, 根據使用者
USB
2.5mm universal connector
