Rigol DS1000D series Manuale utente

User’s Guide RIGOL

Publication number UGA07107-1110

July 2008

DS1000E, DS1000D Series

Digital Oscilloscopes

DS1102E, DS1052E, DS1102D, DS1052D

RIGOL

User’s Guide for DS1000E, DS1000D Series

RIGOL products are protected by patent law in and outside of P.R. China.

Information in this publication replaces all previously corresponding material.

RIGOL Technologies, Inc. reserves the right to modify or change part of or all

the specifications and pricing policies at company’s sole decision.

NOTE: RIGOL is registered trademark of RIGOL Technologies, Inc.

RIGOL

User’s Guide for DS1000E, DS1000D Series

Safety Notices

Review the following safety precautions carefully before operating the instrument to

avoid any personal injuries or damages to the instrument and any products

connected to it. To avoid potential hazards use the instrument as specified by this

user’s guide only.

The instrument should be serviced by qualified personnel only.

To Avoid Fire or Personal Injury

Use Proper Power Cord. Use the power cord designed for the instrument and

authorized in your country only.

Connect and Disconnect Accessories. Do not connect or disconnect probes or

test leads while they are connected to a voltage source

Ground The Instrument. The oscilloscope is grounded through the grounding

conductor of the power cord. To avoid electric shock the instrument grounding

conductor(s) must be grounded properly. Before making connections to the input or

output terminals of the instrument.

Connect The Probe. The probes’ ground terminals are at the same voltage level of

the instrument ground. Do not connect the ground terminals to a high voltage.

Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings

and marks on the instrument. Follow the user’s guide for further ratings information

before making connections to the instrument.

Do Not Operate Without Covers. Do not operate the instrument with covers or

panels removed.

Use Proper Fuse. Use the fuse of the type, voltage and current ratings as specified

for the instrument.

Avoid Circuit or Wire Exposure. Do not touch exposed connections and

components when power is on.

Do Not Operate With Suspected Failures. If suspected damage occurs with the

instrument, have it inspected by qualified service personnel before further

operations.

RIGOL

User’s Guide for DS1000E, DS1000D Series

III

Provide Proper Ventilation. Refer to the installation instructions for proper

ventilation of the instrument.

Do not operate in wet/damp conditions

Do not operate in an explosive atmosphere

Keep product surfaces clean and dry

The disturbance test of all the models meet the limit values of A in the

standard of EN 61326: 1997+A1+A2+A3, but can’t meet the limit values

of B.

Measurement Category

The DS1000E, DS1000D series Digital Oscilloscope is intended to be used for

measurements in Measurement Category I.

Measurement Category Definitions

Measurement Category I is for measurements performed on circuits not directly

connected to MAINS. Examples are measurements on circuits not derived from

MAINS, and specially protected (internal) MAINS derived circuits. In the latter case,

transient stresses are variable; for that reason, the transient withstand capability of

the equipment is made known to the user.

WARNING

IEC Measurement Category I. The input terminals may be connected to circuit

terminal in IEC Category I installations for voltages up to 300 VAC. To avoid the

danger of electric shock, do not connect the inputs to circuit’s voltages above 300

VAC. Transient overvoltage is also present on circuits that are isolated from mains.

The DS1000E, DS1000D series Digital Oscilloscopes is designed to safely withstand

occasional transient overvoltage up to 1000Vpk. Do not use this equipment to

measure circuits where transient overvoltage could exceed this level.

RIGOL

User’s Guide for DS1000E, DS1000D Series

Safety Terms and Symbols

Terms in This Guide. These terms may appear in this guide:

WARNING: Warning statements identify conditions or practices that could

result in injury or loss of life.

CAUTION: Caution statements identify conditions or practices that could

result in damage to this product or other property.

Terms on the Product: These terms may appear on the product:

DANGER indicates an injury hazard may be immediately accessible.

WARNING indicates an injury hazard may be not immediately accessible.

CAUTION indicates that a potential damage to the instrument or other property

might occur.

Symbols on the Product: These symbols may appear on the Instrument:

Hazardous

Voltage

Refer to

Instructions

Protective

Earth Terminal

Test

Grounding

Terminal

Grounding

Terminal of

Chassis

RIGOL

User’s Guide for DS1000E, DS1000D Series

General-Purpose Oscilloscopes

This book covers the following four types of DS1000E, DS1000D Series Digital

Oscilloscopes:

DS1102E, DS1052E,

DS1102D, DS1052D. (With Logic Analyzer)

RIGOL DS1000E, DS1000D Series Digital Oscilloscopes provide exceptional

waveform viewing and measurements in a compact, lightweight package. The

DS1000E, DS1000D series is ideal for production test, field service, research, design,

education and training applications involving analog/digital circuits test and

troubleshooting, as well as education and training.

Features of DS1000E, DS1000D Series:

Dual Channel, Bandwidth:

100MHz (DS1102E, DS1102D)

50MHz (DS1052E, DS1052D)

Optional 16 digital channels (DS1000D series), each channel can be turned on

or off independently, or in a 8 bit group

Mono/Color TFT LCD Displays at 320× 234 resolution

USB storage and printing supports, software upgradeable via USB connectivity

Adjustable waveform intensity, more effective waveform viewing

One-touch automatic setup for ease of use (AUTO)

Saves 10 Waveforms, 10 setups, supports CSV and bitmap format

Newly designed Delayed Scan Function, easy to give attention to both details

and overview of a waveform

20 Automatic measurements

Automatic cursor tracking measurements

Waveform recorder, record and replay dynamic waveforms

User selectable fast offset calibration

Built-in FFT function, Frequency Counter

Digital filters, includes LPF, HPF, BPF, BRF

Pass/Fail Function, optically isolated Pass/Fail output

Add, Subtract and Multiply Mathematic Functions

Advanced trigger types include: Edge, Video, Pulse width, Slope, Alternative,

RIGOL

User’s Guide for DS1000E, DS1000D Series

Pattern and Duration (DS1000D series)

Adjustable trigger sensitivity

Multiple Language User Interface

Pop-up menu makes it easy to read and easy to use

Built-in Chinese and English help system

Easy-to-use file system supports Chinese & English characters input

RIGOL

User’s Guide for DS1000E, DS1000D Series

VII

Content

Safety Notices ..........................................................................................II

General-Purpose Oscilloscopes ................................................................... V

Chapter 1 : Getting Started ............................................................... 1-1

The Front Panel and User Interface ..........................................................1-2

To Inspect the Instrument .......................................................................1-5

To Perform a Functional Check.................................................................1-6

To Compensate Probes............................................................................1-8

Digital Leads (DS1000D Series) ................................................................1-9

To Display a Signal Automatically ...........................................................1-11

To Understand the Vertical System .........................................................1-12

To Understand the Horizontal System .....................................................1-14

To Trigger the Oscilloscope....................................................................1-16

Chapter 2 : Operating Your Oscilloscope ........................................... 2-1

To Set up the Vertical System ..................................................................2-2

Settings of the Channels .....................................................................2-2

Math Functions ................................................................................2-13

Using REF .......................................................................................2-16

Set up LA Channel (DS1000D Series) .................................................2-23

Turn on/off Channels........................................................................2-28

Set up Vertical Position and Scale ......................................................2-29

To Set up the Horizontal System.............................................................2-30

To Set up the Trigger System.................................................................2-36

Settings for Edge Trigger ..................................................................2-38

Settings for Pulse Width Trigger.........................................................2-39

Settings for Video Trigger..................................................................2-41

Slope Trigger ...................................................................................2-45

Alternative Trigger............................................................................2-47

Pattern Trigger (DS1000D Series) ......................................................2-51

Duration Trigger (DS1000D Series) ....................................................2-53

Trigger Setup...................................................................................2-55

To Set up the Sampling System..............................................................2-61

To Set up the Display System.................................................................2-65

To Store and Recall...............................................................................2-67

To Set up the Utility ..............................................................................2-75

RIGOL

User’s Guide for DS1000E, DS1000D Series

VIII

The I/O setup ................................................................................. 2-77

Preference ...................................................................................... 2-78

Self-Calibration................................................................................ 2-79

Pass/Fail ......................................................................................... 2-80

Mask Setting ................................................................................... 2-81

Print Setting.................................................................................... 2-85

Waveform Recorder ......................................................................... 2-86

Language ....................................................................................... 2-91

To Measure Automatically ..................................................................... 2-92

The automatic measurement of voltage parameters............................ 2-96

The automatic measurement of time parameters ................................ 2-97

To Measure with Cursors....................................................................... 2-98

Manual Mode .................................................................................. 2-99

Track Mode ....................................................................................2-102

Auto mode.....................................................................................2-104

To Use Run Control Buttons .................................................................2-105

Chapter 3 : Application & Examples ...................................................3-1

Example 1: Taking Simple Measurements ................................................. 3-1

Example 2: View a Signal Delay Caused by a Circuit................................... 3-2

Example 3: Capture a Single-Shot Signal .................................................. 3-3

Example 4: To Reduce the Random Noise on a Signal................................ 3-4

Example 5: Making Cursor Measurements................................................. 3-6

Example 6: The application of the X-Y operation ....................................... 3-8

Example 7: Triggering on a Video Signal................................................. 3-10

Example 8: FFT Cursor measurement ..................................................... 3-12

Example 9: Pass/Fail Test...................................................................... 3-14

Example 10: Triggering on a Digital Signal.............................................. 3-15

Chapter 4 : Prompt Messages & Troubleshooting ..............................4-1

Prompting Message ................................................................................ 4-1

Troubleshooting ..................................................................................... 4-3

Chapter 5 : Specifications ..................................................................5-1

Specifications......................................................................................... 5-2

General Specifications............................................................................. 5-6

Chapter 6 : Appendix .........................................................................6-1

Appendix A: Accessories.......................................................................... 6-1

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Rigol Apparecchiature di prova

Rigol

Rigol DSO-5200A Manuale utente

Rigol

Rigol DS4024E Manuale utente

Rigol

Rigol DS70000 Series Manuale utente

Rigol

Rigol MSO4000 Series Manuale utente

Rigol

Rigol MSO2000A Series Manuale utente

Rigol

Rigol MSO2000A Series Manuale utente

Rigol

Rigol DS8000-R Series Manuale utente

Rigol

Rigol DS1204B Istruzioni operative

Rigol

Rigol MSO4000 Series Manuale utente

Rigol

Rigol DS7034 Manuale del proprietario

Rigol

Rigol DS1000 Series Istruzioni operative

Rigol

Rigol DG800 Pro Series Istruzioni operative

Rigol

Rigol RP5600A Manuale utente

Rigol

Rigol MSO8000 Series Manuale utente

Rigol

Rigol DS1102/4B Manuale utente

Rigol

Rigol DG900 Pro Series Manuale utente

Rigol

Rigol RP7080S Manuale utente

Rigol

Rigol DS6000 Series Manuale utente

Rigol

Rigol DS70000 Series Manuale utente

Rigol

Rigol MSO8000A Series Manuale utente

Rigol

Rigol MS05000-4CH Manuale utente

Rigol

Rigol DS1302CA Manuale utente

Rigol

Rigol DS1104Z-S Plus Manuale utente

Rigol

Rigol DHO1000 Series Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente