Saltus GFA-OOT Foglio di istruzioni

GFA-OOT
Printed Matter No.9839 1814 01 Geared Front Attachment
Publication Date 2021-01-13
Valid from Serial No. - Product Instructions
Open-end and Offset
Geared Front Attachments
WARNING
Read all safety warnings and instructions
Failure to follow the safety warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference

GFA-OOT EN Product Information
© Saltus Industrial Technique AB - 9839 1814 01 3
Product Information
General Information
WARNING Risk of Property Damage or Severe Injury
Ensure that you read, understand and follow all instructions before operating the tool. Failure to follow
all the instructions may result in electric shock, fire, property damage and/or severe bodily injury.
►Read all Safety Information delivered together with the different parts of the system.
►Read all Product Instructions for installation, operation and maintenance of the different parts of
the system.
►Read all locally legislated safety regulations regarding the system and parts thereof.
►Save all Safety Information and instructions for future reference.
Safety Signal Words
The safety signal words Danger, Warning, Caution, and Notice have the following meanings:
DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or se-
rious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or
serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if
not avoided, could result in minor or moderate injury.
NOTICE NOTICE is used to address practices not related to personal injury.
Country of Origin
For the Country of Origin, please refer to the information on the product label.
Overview
System Description
The Gear Front Attachment (GFA) system is used for tightening and loosening of screws and nuts. The
system can be used for screw connections in locations that are difficult to access.
The tightening operation is controlled by a separate drive unit to which the system is fitted. The drive unit
can be of either pneumatic or electric type.
The modular structure of the system allows for a wide range of configurations available for different screw
connections and tightening processes.
System Components
The modular GFA system is made up of the following main components:

Product Information EN GFA-OOT
4© Saltus Industrial Technique AB - 9839 1814 01
Position Component Function
AAdapter With an adapter the GFA system can be fitted to different inter-
faces. The interface varies depending on the drive unit model.
BGear Front Attachment
(GFA) module
The GFA module comprises a housing which contains a number
of gears, that is, the gear stage. The gear stage depends on the
length of the GFA module.
The output gear, or output socket, can be of type open-end or
closed-end. The open-end type can be used for pipe and hose
connections. The closed-end type is used for regular screw con-
nections.
COutput socket With different sockets the GFA system can be used for various
screw profiles.
GFA System Components

GFA-OOT EN Installation
© Saltus Industrial Technique AB - 9839 1814 01 5
Installation
Installation Instructions
Assembly Instructions
The assembly procedure varies depending on the configuration. Make sure that the square drive of the
drive unit (1) matches the input gear profile (square hole) of the GFA module (2).
Functional Test
Perform a functional test before the first tightening operation and after any performed maintenance activ-
ity.

Installation EN GFA-OOT
6© Saltus Industrial Technique AB - 9839 1814 01
To perform a functional test:
1. Turn the output gear wheel by hand. Turning it in one direction should lock the wheel. In the other di-
rection the gear wheel should be turned easily. The direction for locking (clockwise or counterclock-
wise) depends on the configuration of the specific GFA module.
2. If it is hard to turn, open the housing and check that all components are in the correct position.
3. Grease the system.

GFA-OOT EN Operation
© Saltus Industrial Technique AB - 9839 1814 01 7
Operation
Ergonomic Guidelines
Consider your workstation as you read through this list of general ergonomic guidelines to identify areas
for improvement in posture, component placement, or work environment.
■Take frequent breaks and change work positions frequently.
■Adapt the workstation area to your needs and the work task.
■Adjust for a convenient reach range by determining where parts and tools need to be located to
avoid static load.
■Use workstation equipment such as tables and chairs appropriate for the work task.
■Avoid work positions above shoulder level or with static holding during assembly operations.
■When working above shoulder level, reduce the load on the static muscles by lowering the weight
of the tool, using for example torque arms, hose reels or weight balancers. You can also reduce
the load on the static muscles by holding the tool close to the body.
■Take frequent breaks.
■Avoid extreme arm or wrist postures, particularly during operations requiring a degree of force.
■Adjust for a convenient field of vision that requires minimal eye and head movements.
■Use appropriate lighting for the work task.
■Select the appropriate tool for the work task.
■In noisy environments, use ear protection equipment.
■Use high-quality inserted tools and consumables to minimize exposure to excessive levels of vibra-
tion.
■Minimize exposure to reaction forces.
■When cutting:
A cut-off wheel can get stuck if the cut-off wheel is bent or not guided properly. Use the correct
flange for the cut-off wheel and avoid bending the cut-off wheel during operation.
■When drilling:
The drill might stall when the drill bit breaks through. Use support handles if the stall torque is high.
The safety standard ISO11148 part 3 recommends using a device to absorb a reaction torque
above 10 Nm for pistol grip tools and 4 Nm for straight tools.
■When using direct-driven screwdrivers or nutrunners:
Reaction forces depend on the tool settings and joint characteristics. Strength and posture deter-
mine the amount of reaction force that an operator can tolerate. Adapt the torque setting to the op-
erator's strength and posture and use a torque arm or reaction bar if the torque is too high.
■In dusty environments, use a dust extraction system or wear a mouth protection mask.
Operating Instructions
Operating the GFA System
WARNING Crushing Hazard
Never reach into the open-end head. Moving parts can crush and cut. Keep hands and fingers away
from moving parts.

Operation EN GFA-OOT
8© Saltus Industrial Technique AB - 9839 1814 01
WARNING Crushing Hazard
The Dual trigger forces the user to use both hands to operate the tool. If not used, the operator can
accidentally start the tool while adjusting the crowfoot, thus resulting in a serious hand injury.
►Make sure the tool cannot be started once the Dual trigger has been released.
►Always test the tool by first releasing the trigger of the Dual trigger, then push the trigger of the
tool. If the tool starts; stop working.
WARNING Risk of Injury
Incorrect direction of rotation
►If the output gear is used in the opposite direction of rotation than what is required, only a limited
torque can be absorbed. Exceeding the return flow limiting can lead to severe injuries and prop-
erty damage.
►Observe the rotational direction instructions of the system.
►Always adapt the direction of rotation to the screwing requirements.
WARNING Risk of Injury
Make sure that the correct parameter file is being used. Wrong Parameter File might cause too high
torque with bodily injury as a result.
►Compare the maximum torque which is shown in the controller, with the maximum torque stated
in the stated technical data for the tool, they should be the same.
NOTICE Insufficient Lubrication
If the system is not sufficiently lubricated, it may be damaged.
►Lubricate the system as soon as there is no longer visible grease.
►Apply the grease gun to every grease nipple. Fill with lubricant until it emerges on the output socket.
Tightening procedure:
1. Turn the output gear in reverse direction, by means of the drive unit, until the the output gear locks in
the open position.
2. Place the GFA system with the output gear onto the screw connection.
3. Check that the system is placed correctly on the screw connection.
4. Start screwing by using the drive unit.
5. When tightening is completed, lift up the GFA system from the screw connection. Turn the output
gear in reverse direction, by means of the drive unit, until the output gear locks in the open position.
6. Switch off the drive unit.
7. Remove the system from the screw connection. The system can now be positioned on the next con-
nection.

GFA-OOT EN Service
© Saltus Industrial Technique AB - 9839 1814 01 9
Service
Service Overview
As the gear wheels of the GFA module are exposed to hard wear it is important to regularly check their
condition. If any of the gear wheels are worn or damaged, all the gear wheels must be replaced. Needle
bearings are to be replaced if needed.
At regular intervals between the service, additional grease is to be supplied through the grease nipples.
Maintenance Instructions
Service Intervals and Actions
Interval Action
Daily ■Clean the GFA system
■Inspect the system for any damage
■Check all fastenings of the system
■Run functional tests and listen for any abnormal
noise
At least after every 30,000 tightenings ■Lubricate the system
At least after every 250,000 tightenings ■Service interval for overhaul and preventive main-
tenance
In case of wear-out parts or in case of faulty tightening
result
■Change the output socket gear
■Change the wear-out parts
Preventive Maintenance
Cleaning the System
To clean the system, wipe carefully with a clean, smooth cloth.
Lubrication Instructions
Lubrication Instructions
Component
Recommended
Lubricant Quantity
GFA module Molykote Longterm 2 Plus Until excess grease emerges on
the output socket

Service EN GFA-OOT
10 © Saltus Industrial Technique AB - 9839 1814 01
To lubricate the GFA module:
1. Use a grease gun to apply lubrication to every grease nipple of the GFA module.
The number of grease nipples varies with the design of the GFA module.
2. Operate the system a few times.
3. Remove any excess grease with a clean, smooth cloth.
Dismantling/Assembling Instructions
Dismantling the GFA Module
The instruction below shows an example of a GFA module. The module comprises a housing which
contains a number of gears depending on model of the GFA system.
To dismantle the GFA module:
1. Secure the housing in a vice and loosen the nut.
2. Loosen the cover cap.
3. Remove the bearing housing.
4. Loosen the hex screws. The module can be fastened with two or four hex screws, depending on the
model (2, 3, or 4-stage).
5. Open the housing using a flat screwdriver.
6. Remove the output gear.
Note the direction of the output gear (hexagonal shape up or down). It should be placed in the
same way when assembling the GFA module.
7. Remove the idle gears, needle roller bearings, and shafts.
8. Turn the input gear all the way back to the locked position. Then turn it forward 1/4 of a revolution.
Push in the pawl by using a 0.1 mm feeler gauge. Remove the collar back latch.
9. Remove the pawl and the spring from the collar back latch.
10. Remove the nut from the bearing housing.
11. Remove the input gear from the bearing housing. Remove the ball bearing from the input gear if
needed.
12. Remove the needle roller bearing from the input gear.
Indice
Altri manuali Saltus Utensili



















