SEFRAM MW3366 Manuale utente

USER MANUAL

MW3366

600A

TRMS AC+DC

CLAMP METER

1) SAFETY

This manual contains information and warnings that must be followed for operating the

meter safely and maintaining the meter in a safe operating condition. If the meter is

used in a manner not specified by the manufacturer, the protection provided by the

meter may be impaired.

Observe proper safety precautions when working with voltages above 30 Vrms, 42.4

Vpeak or 60 VDC. These voltage levels pose a potential shock hazard to the user. Do

not expose this product to rain or moisture. The meter is intended only for indoor use.

Keep your hands/fingers behind the hand/finger barriers (of the meter and the test

probe assembly, where applicable) that indicate the limits of safe access of the hand-

held parts during measurements. Inspect lead wires, connectors, and probes for

damaged insulation or exposed metal periodically. If any defects are found, replace

them immediately. Only use the test probe assembly provided with the meter or a UL

Listed test probe assembly to the same meter ratings or better.

Optional offer premium test probe assembly using silicone lead wire insulation, at

agent’s discretion, is equipped with white inner insulation layers as wear indicators.

Replace them immediately if any of the white layers has become visible.

Disconnect the test leads from the test points before changing functions.

The meter meets IEC/EN/BSEN/CSA_C22.2_No./UL standards of 61010-1 Ed. 3.1 and

61010-2-032 Ed. 4.0 to Measurement Categories CAT III 600V and CAT IV 300V AC &

The accompanied test probe assembly meets IEC/EN/BSEN/CSA_C22.2_No./UL

standards of 61010-031 Ed. 2.0 to the same meter ratings or better. The 61010-031

requires exposed conductive test probe tips to be ≤ 4mm for CAT III & CAT IV ratings.

Refer to the category markings on your probe assemblies as well as on the add-on

accessories (like detachable Caps or Alligator Clips), if any, for applicable rating

changes.

INTERNATIONAL SYMBOLS

Marking of Electrical and Electronic Equipment (EEE). Do not dispose of this

product as unsorted municipal waste. Contact a qualified recycler.

Refer to the explanation in this Manual.

Possibility of electric shock

Earth (Ground)

Meter protected throughout by Double Insulation or Reinforced insulation

Fuse

Direct Current (DC)

Alternating Current (AC)

3 Three-phase Alternating Current

Application around and removal from hazardous live conductors is permitted

Brief Information about Measurement Categories

Measurement Category IV is applicable to test and measuring circuits connected at

the source of the building’s low-voltage MAINS installation. Examples are

measurements on devices installed before the main fuse or circuit breaker in the

building installation.

Measurement Category III is applicable to test and measuring circuits connected to

the distribution part of the building’s low-voltage MAINS installation. Examples are

measurements on distribution boards (including secondary meters), circuit-breakers,

wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed

installation, and equipment for industrial use and some other equipment such as

stationary motors with permanent connection to the fixed installation.

Measurement Category II is applicable to test and measuring circuits connected

directly to utilization points (socket outlets and similar points) of the low-voltage MAINS

installation. Examples are measurements on MAINS CIRCUITS of household

appliances, portable tools and similar equipment.

2) EUROPEAN DIRECTIVES AND UK STATUTORY REQUIREMENTS

The instruments conform to EUROPEAN (CE) Low-Voltage Directive 2014/35/EU,

Electromagnetic Compatibility Directive 2014/30/EU, and RoHS 2 Directive 2011/65/EU

plus amendment Directive (EU) 2015/863. The instruments also conform to the UK

(UKCA) Electrical Equipment (Safety) Regulations 2016, Electromagnetic Compatibility

Regulations 2016, and The Restriction of the Use of Certain Hazardous Substances in

Electrical and Electronic Equipment Regulations 2012.

3) PRODUCT DESCRIPTION

1) Antenna area for Non-Contact

EF-Detection

2) Jaw center indicator (with DCA

polarity), at where best current

accuracy is specified

3) Rotary Selector to turn the

power ON/OFF and Select a

function

4) 3-5/6 digits 6000 counts

numeric LCD display

5) Input Jack for all functions

EXCEPT non-invasive DCA,

DC+ACA, or ACA current

functions

6) Common (Ground reference)

Input Jack for all functions

EXCEPT non-invasive DCA,

DC+ACA, or ACA current

functions

7) Push-buttons for special

functions & features.

8) Jaw trigger for opening the

clamp jaw

9) Hand/Finger Barrier to indicate

the limits of safe access of the

meter

10) Clamp Jaw for DC or AC

current magnetic field pick up

11) Additional center indicator for

AmpTipTM Low-current function,

at where best AmpTipTM current accuracy is specified

4) OPERATION

WARNING: Before and after hazardous voltage measurements, test the voltage

function on a known source such as line voltage to determine proper meter functioning.

ACV, DCV, DC+ACV, & Line-level Hz functions

Inputs are made through the test lead terminals COM/+. Defaults at ACV* Function.

Press SELECT button momentarily to select DCV, DC+ACV or Line-level Hz function

in sequence.

Note:

*ACV (and hence AC+DCV & Line-level Hz) function is equipped with digital low-pass

filter, and is capable of dealing with VFD (Variable Frequency Drives) signals. It also

improves ACV reading stability in noisy electrical environments.

Electric Field EF-Detection

The meter displays “EF” when it is ready. Signal strength is indicated as a series of

bar-graph segments on the display together with variable beep tones.

●Non-Contact EF-Detection: An antenna is located along the top-right end of the

stationary clamp jaw, which detects electric field surrounds energized conductors. It is

ideal for tracing live wiring connections, locating wiring breakage and to distinguish

between live or earth connections.

●Probe-Contact EF-Detection: For more precise indication of live wires, such as

distinguishing between Live and Ground connections, use one single probe to test via

terminal COM for direct contact EF-Detection with best sensitivity.

NOTES for Non-Invasive (Clamp-on) Current Measurements:

NOTE

(Application and Removal of the Clamp-on Jaws) For non-invasive current

measurements, press the jaw trigger and clamp the jaws around conductor(s) of only

one single pole of a circuit for load current measurement. Make sure the jaws are

completely closed, or else it will introduce measurement errors. Enclosing conductor(s)

of more than one pole of a circuit may result in differential current (like identifying

leakage current) measurement. Align the conductor(s) to the Jaws center indicators

(Regular or AmpTip™ indicators where applicable) as much as possible to get the best

measuring accuracy. For removal, press the jaw trigger and remove the jaws from the

conductor(s).

Adjacent current-carrying devices such as transformers, motors and conductor wires

may affect measurement accuracy. Keep the jaws away from them as much as

possible to minimize influence.

NOTE

Do not use the meter to measure currents above the rated frequency (400Hz).

Circulating currents may cause the magnetic circuits of the Jaws reach a hazardous

temperature.

Non-Invasive AmpTipTM Low-Current Functions:

ACA, DCA, DC+ACA & Hz

Input is made via the clamp jaws with best accuracy specified near the jaw tip area for

small conductors low-current measurements. Defaults at ACA function. Press SELECT

button momentarily to select the subject functions in sequence.

Non-Invasive Regular Current Functions:

ACA, DCA, DC+ACA, & Hz

Input is made via the clamp jaws with best accuracy specified at the jaw center for

regular current measurements. Press SELECT button momentarily to select the subject

functions in sequence.

 Resistance, Continuity, & Diode functions

Inputs are made through the test lead terminals COM/+. Defaults at  Resistance.

Press SELECT button momentarily to select the subject functions in sequence.

NOTE

When using Diode test function, normal forward voltage drop (forward biased) for a

good silicon diode is between 0.400V to 0.900V. A reading higher than that indicates a

leaky diode (defective). A zero reading indicates a shorted diode (defective). An OL

indicates an open diode (defective). Reverse the test leads connections (reverse

biased) across the diode. The digital display shows OL if the diode is good. Any other

readings indicate the diode is resistive or shorted (defective).

NOTE

Using Resistance, Continuity or Diode function in a live circuit will produce false results

and may damage the meter. In many cases, the suspected component(s) must be

disconnected from the circuit to obtain an accurate measurement reading.

Capacitance functions

Inputs are made through the test lead terminals COM/+.

NOTE

1. Using Capacitance function in a live circuit will produce false results and may

damage the meter. In many cases the suspected component(s) must be disconnected

from the circuit to obtain an accurate measurement reading.

Indice

Altri manuali SEFRAM Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente