SENSIT Technologies HCN Manuale di programmazione

Quick-Start Instructions

IMPORTANT: After testing it may be

necessary to remove condensate collected

in the water/particle lter that is included

with the probe.

WARNINGS:

To prevent ignition of ammable or

combustible atmospheres, disconnect power

before servicing.

Always change batteries in an environment

free of combustible gases.

Do not handle the steel portion of any hot

air probe during or too soon after sampling.

It will become hot and retain heat and burns

may occur!

This is not a substitute for the

instruction manual. It is for

reference only.

Read and understand the

instruction manual before use.

MADE IN USA

Distributed by:

851 Transport Drive

Valparaiso, IN 46383-8432

Phone: 219 465 2700

Web: www.gasleaksensors.com

Innovative Detection Solutions

1. Install the batteries by pushing down

the locking tab and sliding the handle

away from the top of the instrument. When

replacing handle be sure the tab is securely

in place.

2. IMPORTANT: CAREFULLY OBSERVE

POLARITY WHEN CHANGING BATTERIES.

Incorrect installation can damage an internal

“factory service only” fuse.

3. Locate button “A” – push & hold until

the unit powers up, then release the power

button.

4. Allow unit to go through the warm up

sequence in clean air. At the end of warm

up, the unit will auto zero and enter the

working display. This requires from 40 up

to180 seconds.

5. If FAIL is displayed for any of the sensor

readings, make sure the instrument is in

clean air; push and hold the “C” button until

AUTO ZERO is displayed. If this process

does not clear the fail on the display, this

could indicate a problem with the instrument

or sensor.

6. Look at the display – HCN (and optionally

CO) readings are displayed.

7. Alarms will activate at the preset limits.

8. Be sure the short tubing and lter disc are

attached to the back of the instrument.

9. When being used in excessively hot areas

attach the hot air probe assembly to the ¼

turn twist connection on the lter located on

the back of the instrument.

10. Place your nger over the inlet of the

probe and wait ~5 seconds for “FLOW

BLOCKED” to appear on the display. Check

for tight connections if it does not show

“FLOW BLOCKED”.

11. You are now ready to use the instrument.

You can now enter the area and detect gases.

12. When performing HCN/CO checks in

high temp areas do not exceed prolonged

exposures (over 5 min) at 500°F.

13. Press and hold the “C” button to zero

the instrument. (only in a gas free area).

14. When your investigation is complete

push button “A” and hold for 5 seconds until

the instrument displays “POWER OFF” then

release to shut off.

SENSIT®HCN

QUICK-START INSTRUCTIONS

Questo manuale è adatto per i seguenti modelli

Altri manuali SENSIT Technologies Strumento di misura

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies P400 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Manuale utente

SENSIT Technologies

SENSIT Technologies HXG-3 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale di programmazione

SENSIT Technologies

SENSIT Technologies CO Manuale di programmazione

SENSIT Technologies

SENSIT Technologies SPOD Guida rapida

SENSIT Technologies

SENSIT Technologies SENSIT-IT RAMP Manuale utente

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale di programmazione

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies SPOD C1D2 Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD 100 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Manuale utente

SENSIT Technologies

SENSIT Technologies IRED Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HCN Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HXG-2d Manuale di programmazione

SENSIT Technologies

SENSIT Technologies VMD Manuale di programmazione

SENSIT Technologies

SENSIT Technologies Trak-It IIIa Manuale di programmazione

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente