SENSIT Technologies P400 Manuale di programmazione

Quick-Start Instructions

WARNINGS:

To prevent ignition of ammable or combustible

atmospheres, disconnect power before servicing.

To reduce the risk of ignition of a ammable atmosphere,

batteries must only be changed in an area known to be

gas free.

Do not mix batteries of different type or age.

Not for use in atmospheres of oxygen greater than

21%.

Only zero instrument in a gas free environment

To maintain intrinsic safety service must be performed

by factory authorized technicians with approved

replacement parts only.

This is not a substitute for the

instruction manual. It is for

reference only.

Read and understand the

instruction manual before use.Issued: 3-19-2012 Revised: 3-19-2012

MADE IN THE USA

WITH GLOBALLY SOURCED COMPONENTS

Distributed by:

851 Transport Drive

Valparaiso, IN 46383-8432

Phone: 219 465 2700

Web: www.gasleaksensors.com

Innovative Detection Solutions

1. Install Batteries

Using a #1 Phillips Screwdriver loosen the four (4)

battery cover retaining screws. Pull the top of the

battery door (top is located in center of the housing)

downward and remove. This exposes the four (4)

“AA” type alkaline batteries. Remove/replace the

batteries with approved batteries. Replace the

door by inserting the bottom rst and folding the

top into place. Tighten the retaining screws (do not

over tighten).

IMPORTANT: OBSERVE PROPER POLARITY

WHEN INSTALLING THE BATTERIES. Instrument

will not function with improperly installed batteries.

2. Start up

There are two (2) buttons on each side of the

instrument near the center. To start the instrument

push and hold the top button (marked with “O”) on

the right side until the display illuminates.

CAUTION: ALWAYS START THE INSTRUMENT IN

AN AREA OF HAZARD FREE AIR.

Allow the instrument to go through the warm up and

automatically zero. This requires 20 -180 seconds.

The number of days until calibration is due will be

displayed followed by the working display. The

working display shows all sensor readings, the

concentration, the battery voltage (change batteries

when less than 4.2v)

If a FAIL message appears during zero turn the

instrument off and restart in a gas free environment.

The T indicates the activation of the Immediate

Detection System (IDS) for the particular gas.

To activate the backlight for 30 seconds press and

release any button.

3. Bump Test

Attach the calibration cup to the front of the lter

housing and apply the known sample of gas to

insure proper function of the sensors and alarms.

4. Alarms

In the event of an alarm the LED’s will ash, the

backlight will illuminate, a sound will be heard,

and vibration felt. The type of gas in alarm and the

severity (i.e. LO, High, High High, TWA, STEL) will

be displayed.

When the IDS is activated a tick will be heard prior

to the alarm. This can be silenced by pressing and

releasing any button.

Instrument will not turn off when in alarm.

5. Filter cleaning or replacement

Loosen the two lter retaining screws using a 3/32

hex wrench. Remove and clean the foam lter.

Replace if damaged. Replace the cover and tighten

the retaining screws. Do not over tighten.

6. Turn off

Press and hold both top buttons simultaneously.

Continue to hold while the instrument displays

“POWER OFF IN” “4, 3, 2, 1”…then turns off.

Release.

NOTE: P400’s come in many congurations. Read

and understand all instructions and your company

requirements.

CAUTION: Always follow Federal, State, Local and

company practices when using this monitor

SENSIT®P400 (alkaline)

QUICK-START INSTRUCTIONS

Altri manuali SENSIT Technologies Strumento di misura

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale utente

SENSIT Technologies

SENSIT Technologies GOLD CGI Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HXG-2d Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HXG-2 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies GLT Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HCN Manuale di programmazione

SENSIT Technologies

SENSIT Technologies SPOD Guida rapida

SENSIT Technologies

SENSIT Technologies CO Manuale di programmazione

SENSIT Technologies

SENSIT Technologies VMD Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Manuale utente

SENSIT Technologies

SENSIT Technologies SENSIT GOLD G2 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Manuale di programmazione

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale di programmazione

SENSIT Technologies

SENSIT Technologies Trak-It IIIa GLT Manuale utente

SENSIT Technologies

SENSIT Technologies ULTRA-TRAC APL Manuale utente

SENSIT Technologies

SENSIT Technologies SENSIT-IT RAMP Manuale utente

SENSIT Technologies

SENSIT Technologies Trak-It IIIa Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD Manuale di programmazione

SENSIT Technologies

SENSIT Technologies HCN Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GOLD EXCO+1200 Manuale di programmazione

SENSIT Technologies

SENSIT Technologies GAS-TRAC LZ-30 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente