Signode CU-25LH Manuale di istruzioni

IMPORTANT - DO NOT DESTROY THIS MANUAL. It is the customer's responsibility to have all operators and

service personnel read and understand this manual. Contact your local Signode representative for additional copies

of this manual.

GENERAL SAFETY INSTRUCTIONS

READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO

FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE

PERSONAL INJURY.

GENERAL CONSIDERATIONS

1. EYE INJURY HAZARD.

Failure to wear safety glasses with side

shields can result in severe eye injury or

blindness. Always wear safety glasses

with side shields which conform to ANSI

Standard Z87.1 or EN 166.

2. Strap applied to a package is under tension and will

rebound in an outward direction when cut.

3. Before using the cutter read its operation and safety

instructions.

4. Use the correct Signode strap cutter for your application;

if you need help contact your Signode representative.

Never use a claw hammer, crowbar, chisel, ax, or similar

tool to cut or break strap. Such tools will cause the strap

to fly apart with hazardous force.

5. Keep work areas uncluttered and well lit.

6. Maintain proper footing and balance when cutting strap.

Do not cut strap when you are in an awkward position.

Take additional care when cutting ties on compressed

loads; strap will recoil with a much greater force. Be

careful when cutting straps as the load can shift.

7. Strap should always be cut square; strap cut at an angle

has a much sharper end.

8. Dispose of all cut strap. Never leave it lying on the

ground where it can present a tripping hazard. Never re-

use strap.

9. Take good care of the cutter. Inspect it daily for worn or

damaged cutting surfaces. Do not use this tool if these

surfaces are worn or damaged.

10. Always wear protective gloves when

handling strap or sharp parts.

CU-25LH STRAP CUTTER

Part No. 022654

For cutting all strap up to 2" x .050" (50mm x

1.27mm).

CUTTING TENSIONED STRAP

1. Keep personnel at safe distance, away from possible

flying strap ends.

2. Stand to one side of the strap as it is being cut, OUTSIDE

OF THE DANGER ZONE (dotted area).

3. Cut strap.

CU-25LH PARTS LIST

Key Qty Part No. Description

1* 1 005744 Top cutter blade

2** 2 003911 Flexloc nut, thin 5/16-24 std.

31 161177 Top handle assembly

4 2 005753 Bolt 5/16-24 x 1-5/16

5 1 005745 Handel link

6 1 005746 Cutter lever

7 1 005748 Cutter drive pin

8 1 161178 Bottom handle assembly

9** 2 005747 Cutter lever bolt

10 1 005743 Bottom cutter blade

11** 1 005749 L. H. bolt

12 2 020378 Handel grip

* Can be reversed when worn.

** Use Loctite #271 on threads only.

!Apply a light machine oil to all moving parts of this tool.

!When ordering parts, please show tool model, part number and name.

!Wearing parts are underlined and should be stocked.

!Common hardware parts may obtained at any local hardware supply.

Questo manuale è adatto per i seguenti modelli

Altri manuali Signode Utensili

Signode

Signode JOSEF KIHLBERG B53PN Manuale utente

Signode

Signode Josef Kihlberg JK20V779L22 Manuale utente

Signode

Signode Josef Kihlberg JK35T590 Manuale utente

Signode

Signode PRHM-34 Manuale di istruzioni

Signode

Signode B/91001 Manuale utente

Signode

Signode Josef Kihlberg JK20V779L Manuale utente

Signode

Signode Josef Kihlberg B560PN Manuale utente

Signode

Signode AMPT-12 Guida

Signode

Signode Josef Kihlberg JK20A680L Manuale utente

Signode

Signode Tension-Weld BTS-16 Manuale di istruzioni

Signode

Signode JOSEF KIHLBERG JK10-680 Manuale utente

Signode

Signode Josef Kihlberg F560PN Manuale utente

Signode

Signode PNSC-2 Manuale di istruzioni

Signode

Signode TENSION-WELD VXT2-19 Manuale di istruzioni

Signode

Signode Josef Kihlberg R557PN Manuale utente

Signode

Signode Josef Kihlberg JK20-680FN Manuale utente

Signode

Signode TENSION-WELD VT-16HD Manuale di istruzioni

Signode

Signode PN2-2 Manuale di istruzioni

Signode

Signode VT-16 Manuale di istruzioni

Signode

Signode AHP-34 Manuale di istruzioni

Signode

Signode Josef Kihlberg R555PN Manuale utente

Signode

Signode Josef Kihlberg B561PN Manuale utente

Signode

Signode TENSION-WELD VT-19HD Manuale di istruzioni

Signode

Signode SCM-12 Manuale di istruzioni

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare