SIIG JJ-E02211-S1 Manuale utente
1
DP CyberParallel
Dual PCIe
Installation Guide
04-0964A
Introduction
The DP CyberParallel Dual PCIe adds 2 high-
speed parallel ports to PCI Express enabled
systems and supports EPP/ECP and SPP
(standard) parallel port modes.
Features and Benefits
•PCI Express 1-lane (x1) I/O card works
with PCI Express slots with different lane
width
•Two parallel ports support ECP, EPP PS2
and SPP modes and works with various
types of parallel devices
• Supports various types of Windows®- based
application software
2
System Requirements
•PCI Express enabled system with an
available PCI Express slot
•Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000
Package Contents
•DP CyberParallel Dual PCIe host card
• FP bracket DB25 ribbon cable (plugged on
the board)
• LP bracket DB25 ribbon cable
• Spare low profile bracket for host card
• Driver CD
• Installation guide
3
Figure 1
*Note: When connecting the DB25 ribbon
cable to Parallel Port 2 (P2), position the
ribbon cable so the stripe is on the side
nearest to the slot bracket, see Figure 1.
Parallel Port
1 (P1)
Parallel Port
2 (P2)*
Stripe
Layout
pin 1
4
Hardware Installation
Note: For low profile systems, replace the
currently mounted bracket with the included
low profile bracket.
General instructions for installing the card are
provided below. Since the design of computer
cases and motherboards vary, refer to your
computer's reference manual for further
information, if needed.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching
your computer case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
1. Turn OFF the power to your computer.
2. Unplug the power cord and remove the
computer cover.
3. Remove the slot bracket from an available
PCIe slot.
5
4. If you need the second parallel port, connect
the DB25 connector bracket now and
remove another slot bracket cover from an
available PCIe slot. Skip this step if you
need only one parallel port.
5. Carefully align the card to the selected PCIe
slot, push the board down firmly, but gently,
until it is well seated.
6. Replace the slot bracket holding screw to
secure the card.
7. Mount the second parallel port and secure
it with the slot bracket holding screw. Skip
this step if you need only one parallel port.
8. Replace the computer cover and reconnect
the power cord.
Software Installation
This section provides the steps on how to install
the DP CyberParallel Dual PCIe drivers. Please
make sure the board is installed before proceeding
with the driver installation.
6
Windows 8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / Server 2008 (32-/64-bit) /
Server 2008 R2
1. Insert the driver CD. Close the CD autoplay
box if prompted.
2. Check in Device Manager.
For Windows 8 / 7: Right click Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows Server 2008 / 2008 R2: Right
click Computer, click Manage, double click
Diagnostics, then click Device Manager.
Right click Computer, click Manage, click
Device Manager.
3. Right click PCI Parallel Port, click Update
Driver Software.
4. Click Browse my computer for updated
software.
For 32-bit: Type D:\32bit, click Next.
(Change D: to match your CD-ROM drive
letter)
7
For 64-bit / 2008 R2: Type D:\64bit, click
Next. (Change D: to match your CD-ROM
drive letter)
5. At Windows has successfully updated
your driver software, click Close.
6. Go back to Device Manager, right click PCI
Parallel Port, then click Update Driver
Software.
7. Repeat steps 4& 5, then restart the computer
to complete the installation.
Windows XP (32-/64-bit) / Server 2003 (32-/
64-bit)
1. Click Cancel at the Found New Hardware.
2. Insert the driver CD. Close the CD autoplay
box if prompted.
3. Right click My Computer, click Manage,
click Device Manager.
4. Click Update Driver...
5. Select Install from a list or specific location
(Advanced), then click Next.
6. Check Include this location in the search,
uncheck the other box.
8
For 32-bit: Type D:\32bit, click Next.
(Change D: to match your CD-ROM drive
letter)
For 64-bit: Type D:\64bit, click Next.
Change D: to match your CD-ROM drive
letter)
7. At Completing the Hardware Update
Wizard, click Finish.
8. Go back to Device Manager, right click PCI
Parallel Port.
9. Repeat steps 4 - 7, then restart the computer
to complete the installation.
Windows 2000
1. Insert the driver CD. Close the CD autoplay
box if prompted.
2. At the Found New Hardware Wizard, click
Next.
3. Select Search for a suitable driver for my
device (recommended), then click Next.
4. Select Specify the location, uncheck the
other boxes, then click Next.
9
5. Type D:\32-bit, click OK, then click Next
(Change D: to match your CD-ROM drive
letter)
6. At Completing the Found New Hardware
Wizard, click Finish, then restart the
computer to complete the installation.
To Verify Windows Installation
1. Check in Device Manager to verify
installation.
For Windows 8 / 7: Right click Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows XP / Server 2003 / 2000: Right
click My Computer, click Manage, click
Device Manager.
For Windows Server 2008 / 2008 R2: Right
click Computer, click Manage, double click
Diagnostics, then click Device Manager.
2. Double click Ports (COM & LPT), two PCI
ECP Parallel port... should be displayed.
10
Changing Parallel Port
Some parallel port devices need a specific LPT in
order to function properly. If your device works,
do not make any changes.
1. For Windows 8 / 7 / XP / 2003 / 2000: Right
click Computer or My Computer, click
Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Server 2008 / 2008 R2: Right click
Computer, click Manage, double click
Diagnostics, then click Device Manager.
2. Double click Ports (COM & LPT), then
double click the PCI ECP Parallel port you
want to change.
3. Click Port Settings tab.
4. Click the down arrow next to the LPT Port
Number box, then select a parallel port that
is not in use.
5. Click OK to save the changes.
Indice
Altri manuali SIIG Hardware per computer
SIIG
SIIG JU-P40412-S1 Manuale utente
SIIG
SIIG ExpressCard/54 CF R/W Manuale utente
SIIG
SIIG NN-403P12 Manuale utente
SIIG
SIIG ExpressCard/54 CF R/W Manuale utente
SIIG
SIIG eSATA II PCIe i/e Manuale utente
SIIG
SIIG Dual Profile Hi-Speed USB 4-Port PCI Manuale utente
SIIG
SIIG JU-2NE012 Manuale utente
SIIG
SIIG NN-000032-S1 Manuale utente
SIIG
SIIG CE-H23J11-S1 Manuale utente
SIIG
SIIG ExpressCard 11-in-1 Reader/Writer Manuale utente
SIIG
SIIG USB 2.0+1394 DV Kit Manuale utente
SIIG
SIIG SATA II-150 PCI Manuale utente
SIIG
SIIG DP FireWire 800 3-Port PCIe Manuale utente
SIIG
SIIG NN-8CB212-S1 Manuale utente
SIIG
SIIG USB 2.0 5-Port PCI Manuale utente
SIIG
SIIG UltraATA 100 Pro Manuale utente
SIIG
SIIG FireWire Dual-Port CardBus Manuale utente
SIIG
SIIG SATA II PCIe RAID Manuale utente
SIIG
SIIG SC-SAE312-S3 Manuale utente
SIIG
SIIG DP SoundWave 4 Channel PCI Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
