SIIG SC-SAE312-S3 Manuale utente

eSATA II PCIe Pro RAID

Quick Installation Guide

04-0396B

Introducing the eSATA II PCIe Pro RAID

The eSATA II PCIe Pro RAID is an ultra high-speed two

channel Serial ATA Generation II RAID controller for use

in PCI Express enabled systems.

Features and Benefits

• Compliant with PCI Express Base Specification 1.0a

• Compliant with Serial ATA 1.0 specifications with

support for full complement of SATA II optional

features

• PCI Express 1-lane (x1) SATA II adapter works with

PCI Express slots with different lane width

• Installs in any available PCI Express slot and

supportsdatatransferratesupto3.0Gbps(300MBps)

• Supports Native Command Queuing (NCQ),

Non-zero offsets NCQ, and Out-of-order data

delivery NCQ

• Independent command fetch, scatter/gather, and

command execution

• Supports RAID 0 (striping) and RAID 1 (mirroring)

for speed and data protection respectively

System Requirements

• PCI Express enabled system with one available PCI

Express slot

• Windows 2000/XP (32-/64-bit)/Server 2003

(32-/64-bit)/Vista (32-/64-bit)

• 2 External SATA drives

PackageContents

•eSATA II PCIe Pro RAID board

• Driver software CD

• Quick Installation Guide

Layout

HDD Activity

LED

HDD LED pins

(Front chassis LED;

connects horizontally)

External

connectors

Figure 1. eSATA II PCIe Pro RAID layout

Hardware Installation

General instructions for installing the card are provided

below. Since the design of computer cases and

motherboards vary, refer to your computer’s reference

manual for further information, if needed.

Static Electricity Discharge may permanently damage

your system. Discharge any static electricity build up in

your body by touching your computer case for a few

seconds. Avoid any contact with internal parts and

handle cards only by their external edges.

1. Turn OFF the power to your computer and any

other connected peripheral device.

2. Unplug the power cord from the back of the

computer.

3. Remove your computer cover.

4. Remove the slot bracket from an available PCI

Express slot.

5. To install the card, carefully align the card's bus

connector with the selected PCI Express slot on the

motherboard. Push the board down firmly, but

gently, until it is well seated.

6. Replace the slot bracket holding screw to secure the

card.

7. Replacethecomputercover and reconnect the power

cord.

External Device Connection

External Serial ATA hard disk drives should come with

their own accessories. In most cases, you just need to

powerup the externaldevice and connect it tothe external

port.

The eSATA II PCIe Pro RAID is a two channel Serial ATA

controller that supports two Serial ATA hard disk drives.

It is recommended to use identical drives for all RAID

configurations, however, it's possible to combine hard

drives of different sizes and makes.

RAID Arrays

RAID Arrays are setup in the eSATA II PCIe Pro RAID

BIOS.

Table of Contents

RAID 0 (Striping)............................................ page 4-5

RAID 1 (Mirror) .............................................. page 5-6

Single Drive Setup (Contiguous).................... page 7

JBOD Drive Setup (Concatenated) .............. page 7-8

Rebuilding a Failed Mirror Set .................... page 8-9

Deleting RAID Arrays ...................................... page 9

Resolving Conflicts......................................... page 10

Low Level Format........................................... page 10

Logical Drive Info ........................................... page 10

BIOS Configuration ........................................ page 10

RAID 0 (Striping)

This RAID array to be used on New/Blank hard drives.

Striping will destroy existing data on the hard drive.

Auto Configuration is recommended. For applications

that require a custom chunk size, Manual Configuration

is offered.

Auto Configuration (recommended)

The default chunk size is 64k when selecting Auto

configuration.

1. AstheBIOS boots pressCtrl+Sor F4 when prompted

to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then

press Enter.

3. Select RAID0, then press Enter.

4. Select Auto configuration, then press Enter.

5. Input the RAID size, then press Enter.

6. When asked Are You Sure (Y/N)?, press Yto accept.

7. Press Ctrl+E to exit the BIOS.

8. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

9. Continue with Fdisk and Format steps as if you

were installing a conventional hard drive.

Manual Configuration

1. AstheBIOS boots pressCtrl+S orF4whenprompted

to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then

press Enter.

3. Select RAID0, then press Enter.

4. Select Manual configuration, then press Enter.

5. Select chunk size from 8k, 16k, 32k, 64k or 128k,

then press Enter.

6. Select the first drive, then press Enter.

7. Select the second drive, then press Enter.

8. Input the RAID size, then press Enter.

9. When asked Are You Sure (Y/N)?, press Yto accept.

10. Press Ctrl+E to exit the BIOS.

11. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

12. Continue with Fdisk and Format steps as if you

were installing a conventional hard drive.

RAID 1 (Mirror)

For New/Blank Hard Drives

1. AstheBIOS boots pressCtrl+S orF4whenprompted

to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then

press Enter.

3. At the next screen select RAID1, then press Enter.

4. Select Auto configuration, then press Enter.

5. Input the RAID size, then press Enter.

6. When asked Are You Sure (Y/N)?, press Yto accept.

7. Press Ctrl+E to exit the BIOS.

8. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

9. Continue with Fdisk and Format steps as if you

were installing a conventional hard drive.

For Existing Hard Drives with Data

1. AstheBIOS boots pressCtrl+S orF4whenprompted

to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then

press Enter.

3. At the next screen select RAID1, then press Enter.

4. Select Manual configuration, then press Enter.

5. Select the Source drive, then press Enter.

6. Select the Target drive, then press Enter.

7. Select Create with data copy, then press Enter.

8. Select online copy, then press Enter.

Note:SelectingOnline Copybuildsthe mirror while

in Windows. Selecting Offline Copy builds the

mirror before exiting the RAID BIOS.

9. Input the RAID size, then press Enter.

10. Press Ctrl+E to exit the BIOS.

11. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

Single Drive Setup

Setting up your hard drive to operate as a single drive

maydestroyallexistingdataonyourharddrive,therefore,

back up any data on your hard drive before connecting it

to the raid controller or use a blank or new hard drive.

1. AstheBIOS boots pressCtrl+S orF4whenprompted

to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then

press Enter.

3. Select Concatenation, then press Enter.

4. Select 1, then press Enter.

5. Select a hard disk drive, then press Enter.

6. When asked Are You Sure (Y/N)?, press Yto accept.

Note:In the RAIDBIOSscreen, under Logical Drive,

SiI Concatenation and the size of the logical drive

will appear.

7. Press Ctrl+E to exit the BIOS.

8. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

Note: The hard disk will show up as Contiguous in

the SATARAID5 GUI.

JBOD Drive Setup

This RAID Array combines the full capacity of two hard

drives to form one logical drive. Since this configuration

will destroy all existing data on your hard drives, use

blank or new hard drives or back up your existing data

before connecting to the raid controller.

1. AstheBIOS boots pressCtrl+S orF4whenprompted

to enter the RAID BIOS.

2. At the next screen select Create RAID Set, then

press Enter.

3. Select Concatenation, then press Enter.

4. Select 2, then press Enter.

5. Select one hard disk drive, then press Enter.

6. Select the second hard disk drive, then press Enter.

7. When asked Are You Sure (Y/N)?, press Yto accept.

Note:IntheRAID BIOS screen,underLogicalDrive,

SiI Concatenation and the size of the logical drive

will appear.

8. Press Ctrl+E to exit the BIOS.

9. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

Note: When two drives are combined using JBOD,

each hard disk drive will appear as Concatenated

in the SATARAID5 GUI.

Rebuilding a Failed Mirror Set

When a failure to one member occurs, you will be notified

either by the RAID BIOS during boot or by the SATA

Raid5 GUI while in Windows. The steps below will

guide you in rebuilding a failed mirror set.

For Offline Mirror Rebuild (SATA RAID BIOS)

1. Replace the failed drive with one of equal or greater

capacity, then start the computer.

2. During boot press Ctrl+S or F4 to enter the RAID

BIOS.

3. Select Create RAID Set, then press Enter.

4. Select SPARE DRIVE, then press Enter.

5. Select the single hard drive then press Enter.

6. Input the RAID size, press Enter. When asked Are

You Sure (Y/N)?, press Yto confirm.

7. Select Rebuild Raid 1 Set, press Enter.

8. When asked Are you sure (Y/N)?, press Yconfirm.

The mirror will begin rebuilding. Do not interfere

with the process.

9. When rebuilding is finished, press Ctrl+E.

10. When asked Are you sure to exit (Y/N)?, press Yto

exit and reboot.

For Online Mirror Rebuild (in Windows)

1. Replace the failed drive with one of equal or greater

capacity, then start the computer.

2. When Windows resumes, at the SATA SoftRaid 5

screen, click Legacy Support, then click Rebuild

Legacy RAID Group.

Note: If Legacy Support does not show, click File,

Configuration, Advanced Options. Check Legacy

(Bootable) Support, then click OK.

3. At Rebuild Legacy RAID Group box, select both

hard drives, then click Rebuild.

4. Click OK, then click Cancel to close the window.

5. The mirror will rebuild. Rebuild time is dependant on

the size of the mirror set.

Deleting RAID Arrays

1. AstheBIOS boots pressCtrl+S orF4whenprompted

to enter the RAID BIOS.

2. Select Delete RAID Set, then press Enter.

3. Select the RAID set, then press Enter.

4. Whenasked AreYouSure(Y/N)?,pressYtoconfirm.

Resolving Conflicts

When a RAID set is created, the metadata written to the

disk includes drive connection information. If, after a

disk failure, the replacement disk was previously part of

a RAID set (or used in another system), it may have

conflicting metadata. If so, this will prohibit the RAID set

from being either created or rebuilt, in order for the RAID

set to function properly, this old metadata must be first

overwritten with the new metadata. To resolve this, from

the main BIOS window select Resolve Conflicts, then

press Enter, the correct metadata, including the correct

drive connection information, will be written to the

replacement disk.

Low Level Format

Low Level Format is built into the RAID BIOS to make it

more convenient to erase the entire contents of a hard

disk drive, including data, drive and partition

information. The Low Level Format utility works on

singlehard drives only,before the RAIDset is configured.

Logical Drive Info

This menu item displays the assignment of physical

driveswithinalogicalset(RAID0,RAID1,Concatenated).

This is a display only function.

BIOS Configuration

The eSATA II PCIe Pro RAID BIOS will appear everytime

your system starts up. During this (Post) process, the

bios will show up and indicate the devices attached to it.

If the bios doesn't show, please install your controller

into another PCIe slot.

Indice

Altri manuali SIIG Hardware per computer

SIIG

SIIG DP FireWire 800 PCIe Manuale utente

SIIG

SIIG CyberSerial POS 4000RJ Manuale utente

SIIG

SIIG SATA II-150 PCI Manuale utente

SIIG

SIIG NN-PCMM12-S3 Manuale utente

SIIG

SIIG eSATA II PCIe i/e Manuale utente

SIIG

SIIG CyberParallel Dual Manuale utente

SIIG

SIIG ID-P40411-S1 Manuale utente

SIIG

SIIG 1 FireWire 800 CardBus DV-Ki Manuale utente

SIIG

SIIG IO1037 Manuale utente

SIIG

SIIG 1-Port ECP Manuale utente

SIIG

SIIG ExpressCard 11-in-1 Reader/Writer Manuale utente

SIIG

SIIG Dual Profile Hi-Speed USB 4-Port PCI Manuale utente

SIIG

SIIG NN-PC8312-S2 Manuale utente

SIIG

SIIG DP FireWire 800 PCIe Manuale utente

SIIG

SIIG CyberParallel Dual Manuale utente

SIIG

SIIG Serial ATA PCI Manuale utente

SIIG

SIIG Serial ATA 4-Channel PCI Manuale utente

SIIG

SIIG Silent Mini Notebook Cooler Manuale utente

SIIG

SIIG I/O Expander 2S Manuale utente

SIIG

SIIG DP FireWire 800 3-Port PCIe Manuale utente

SIIG

SIIG DP PCI-to-PS/2 Manuale utente

SIIG

SIIG USB 2.0+1394 DV Kit Manuale utente

SIIG

SIIG Cyber PCI I/O Manuale utente

SIIG

SIIG JJ-E01111-S1 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente