Smartech TECH-5000P Manuale utente

User Guide
Guía del usuario
Smartech TECH-5000P Power Kit
Kit de alimentación Smartech TECH-5000P
Model/Modelo TECH-5000P
CAUTION:
Read and follow all safety
rules and operating instructions
before every use of this product.
SAVE THESE INSTRUCTIONS.
ATENCIÓN:
Lea y siga todas las reglasde
seguridad e instrucciones de uso
antes de cada uso de este producto.
GUARDE ESTAS INSTRUCCIONES.

USER’S MANUAL PAGE 2TECH-5000P
FULLY CHARGE IMMEDIATELY AFTER PURCHASE.
Fully recharge after each jumpstarting, or every 3 months to ensure
long battery life.
What’s included with the Smartech TECH-5000P Power Kit

USER’S MANUAL PAGE 3TECH-5000P
IMPORTANT SAFETY INSTRUCTIONS
1. Use the TECH-5000P Power Kit for jumpstarting a 12V
LEAD-ACID battery only. Do not attempt to jump-start a vehicle
with a non-rechargeable or defective battery.
2. Working in vicinity of a lead-acid battery is dangerous.
Batteries generate explosive gases during normal operation.
Use in well-ventilated area. Battery acid can cause permanent
blindness. Avoid touching eyes while working near battery.
3. Do not smoke, strike a match, or cause a spark in vicinity of
battery or engine. Avoid explosive gas, ames and sparks.
4. Remove all personal jewelry, such as rings, bracelets,
necklaces, and watches before jumpstarting operations. These
items may produce a short-circuit that can cause severe burns.
5. To avoid damage to the vehicle’s electrical system, do not use
the TECH-5000P Power Kit on a vehicle that has no battery
installed.
6. Use of an accessory not recommended or sold by the
manufacturer may result in a risk of re, electric shock or injury
to persons. Do not operate with damaged accessory(s).
7. Locate the TECH-5000P 500A Lithium Jump Starter &
Portable Power Supply as far away from battery as jumper
cables permit.
8. Do not expose to rain or wet conditions.
9. To reduce the risk of damage to electric plug and cord, pull by
the plug rather than the cord when disconnecting.
10. Operate with caution if the jump starter has received direct
hit of force or been dropped. Have it checked and repaired if
damaged.

USER’S MANUAL PAGE 4TECH-5000P
11. Any repair must be carried out by the manufacturer or an
authorized repair agent in order to avoid danger.
TECH-5000P POWER BANK / JUMP STARTER
The Power Bank / Jump Starter features a low voltage protection
(for Power Bank / Jump Starter itself), spark proof, reverse polar-
ity protection and short circuit protection. This Power Bank / Jump
Starter can instantly jump start most single battery vehicles, up
to 60+ (over 60) times on a full charge. The Power Bank / Jump
Starter is also equipped with USB power output, LED ashlight,
19VDC power output and 12VDC power output.

USER’S MANUAL PAGE 5TECH-5000P
Battery Type Lithium-ion Polymer
Battery Capacity 44.4WH
Starting Current 250A
Peak Current 500A
Jump Start up to 5.5L Gas Engine
USB Output 5V/2.4A, 5V/2.4A
LED Flashlight 1W
19V Output 19V/3.5A for Laptops
12V Output 10A Max
Operating Temperature -22˚F ~ +122˚ F
Charging Temperature 32˚F ~ +104˚F
Storage Temperature -4˚F ~ +95˚F (for 3 months)

USER’S MANUAL PAGE 6TECH-5000P
PRODUCT FEATURES AND LAYOUT
LCD DISPLAY
ENGINE START
Socket
LCD
15V/1A
Input Port
19V
Output Port
12V
Output Port
USB Output
Ports
Flashlight
Button
Power
Button
1 2 3 4 5 6
7 8 9
1. 15V/1A input
2. 5V/2.4A output
3. Light steady on
4. Light FLASH
5. 5V/2.4A output
6. Light SOS
7. Battery capacity
8. 12V output
9. 19V output

USER’S MANUAL PAGE 7TECH-5000P
SMART JUMPER CLAMPS
Red
LED BOOST
Button
EC5
Plug
Negative
Clamp
Positive
Clamp
Green
LED
CHARGING
This product is partially charged from the manufacturer. Fully
charge the unit immediately after purchase. In order to prolong the
product life, be sure to fully recharge the unit after each
jumpstarting, or every 3 months even if this unit has not been used.
If battery voltage in the TECH-5000P Power Kit is too low. The unit
will shut off to prevent damage to itself. Recharge as soon as
possible to be activated and fully charge it to ensure long battery
life. In addition, it is not recommended to charge and discharge the
Power Bank at the same time.

USER’S MANUAL PAGE 8TECH-5000P
CONNECTING TO THE BATTERY
JUMP STARTING
1. Identify polarity of battery posts. The positive battery terminal
is typically marked by these letters or symbol (POS,P,+). The
negative battery terminal is typically marked by these letters or
symbol (NEG,N,-).
2. Do not make any connections to the carburetor, fuel lines, or
thin metal parts.
3. Identify if you have a negative or positive grounded vehicle.
This can be done by identifying which battery post (NEG or
POS) is connected to the chassis.
4. For a negative grounded vehicle (most common): connect the
RED POSITIVE jumper clamp rst to the positive battery termi-
nal, then connect the BLACK NEGATIVE jumper clamp to the
negative battery terminal or vehicle chassis.
5. For a positive grounded vehicle (very uncommon): connect the
BLACK NEGATIVE jumper clamp rst to the negative battery
terminal, then connect the RED POSITIVE jumper clamp to the
positive battery terminal or vehicle chassis.
6. When disconnecting, disconnect in the reverse sequence,
removing the negative rst (or positive rst for positive ground
systems).
1. This unit is only for emergency use, not for frequent commercial
use! ENGINE START socket is ALWAYS activated! Do not attempt
to jumpstart your vehicle when the TECH-5000P Power Bank
battery capacity is below 30%.
2. Turn off the vehicle ignition and all accessories (radios, lights, air
conditioners, etc.), and disconnect electronic devices.
3. Connect the jumper clamps to the correct polarity battery terminals.

USER’S MANUAL PAGE 9TECH-5000P
4. Connect the EC5 plug of smart jump clamp to the ENGINE
START socket of TECH-5000P PowerBANK. Wait a few seconds,
the green LED light on smart jump clamp should be lit. If not, please
refer to “BOOST” OPERATION section.
5. Try starting the vehicle (turn on the ignition switch). Most vehicles
will immediately start. Stop if the vehicle does not start after
5 seconds of engine cranking. The jumpstart feature is designed
for short term operation only, and more than 5 seconds may cause
damage to the unit. Allow the jump starter to cool down for at least 3
minutes after each jumpstarting.
6. Disconnect the smart jump clamp from the TECH-5000P Power
Bank immediately after engine starts, and then remove from battery
terminals.
“BOOST”OPERATIONS:
1. Under normal circumstance, the green LED light should be
turned on automatically. If not, please do the following: with
correct connection between Jump Starter and vehicle battery
(Red LED keeps on and green LED is off), press and hold
BOOST button for 3 seconds (after a buzzer sound, the green
LED is on and red LED is off). Usually this is because the
vehicle battery capacity is low.
2. Start the engine (same method as the normal operations in
Page 9).

USER’S MANUAL PAGE 10TECH-5000P
LED AND BUZZER COMMUNICATION:
No. Red LED Green
LED
Buzzer
Sound
Condition
1 On Off One sound Smart jump clamp and
Tech-5000P power bank
are connected.
2 Off On One sound Smart jump clamp and
vehicle battery are
connected.
Ready to start the engine.
3Off No buzzer Lithium battery voltage in
the TECH-5000P Power
Kit is rather low.
Cautions:
1. Under normal circumstances, do not use the mandatory
operations.
2. The spark proof, reverse polarity protection and short cir-
cuit protection features are disabled after BOOST button is
pressed. Pay very close attention to the polarity of the battery
before using this mode. Do not allow the positive and negative
battery clamps to touch or connect to each other as the item
will generate sparks and high heat if not used properly.
Altri manuali per TECH-5000P
1
Indice
Altri manuali Smartech Utensili


















