Sumake SF501 Manuale utente

INSTRUCTION MANUAL

ITEM NO.: SF501, SF502

AUTOMATIC SCREW SUPPLIER

SF501

SF502

SF501(2)-I-1905B-YM

Table of Contents

ⅠAbout SF501 / SF502

1. Features ……………………………………………………..…. P3

2. Specifications…………………………………………………..….P3

ⅡInstallment

1. Preparation……………………………………………………..….P4

2. Tryout ..………………………………………………………..….P6

3. Normal Operation………………………………………………....P9

4. After Operation…………………………………………………....P9

5.Maintenace .… ……………………………………………………P9

ⅢAdjustment and Replacement

1. Air Pressure Adjustment…………………………………………..P12

2. Adjustment of escapement speed ………………………………..P13

3. Torque Adjustment ………………………..……………………..P14

ⅠAbout SF501/ SF502

Designed for speed, stability, and convenience.

Improving screw driving speed and work efficiency by integrating pneumatic/ electric screwdriver,

high-tech automatic feeder, and high precision jaw.

The jaw is customized by particular screw and working environment to provide a stable operation.

Standard pneumatic screwdriver; optional models by customer also available.

1. Features

Model Voltage Air pressure

SF501 220 V 5 kg / cm2

Model Voltage Air pressure

SF502 220 V 5 kg / cm2

ⅡInstallment

1. Preparation:

(1) Connect the screw delivery hose, air hose and signal cable to the feeder unit

Take a balance of the driver unit for easier fastening. While taking balance, make

sure that the signal cable and air hose do not contact with hook or balancer wire.

Care should be taken to prevent excessive bending or twisting of hoses and cables,

since this can cause damage or disconnection.

Connect the screw delivery hose between the feeder and the driver as soon as

possible. Make sure that it is not excessively bent or twisted after installation.

◆For pneumatic screwdriver only.

Connect delivery hose Connect air hose

Connect signal cable

◆For electric screwdriver only.

Connect delivery hose Connect wire of elec. screwdriver

1. Connect feeder unit to compressed air source (air pressure 4-5 kg/cm2.)

2. Adjust air pressure

Connect air source Adjust air pressure

4. Check screw delivery timer setting on the front of the feeder unit. Standard operation

setting is approximate 0.5

5. Connect power cord to a single-phase AC-220 wall outlet.

Check delivery timer Connect power cord

2. Tryout:

(1) Open the cover of machine then load some screws.

Load screw Max. volume

(2) Turn power switch on

Check whether the light of power and VFD is “ON”.

Turn power switch on

(3) Check whether feeding action is normal

One cycle will send a signal to the feeder from the driver unit and the escapement will release

one screw from the chute for delivery to the driver’s tip by compressed air. First cycle has a 3~5

seconds delay of feeding.

Never point the driver tip toward a person since a screw might shot out accidentally, causing

possible injury.

(4) Check the pneumatic screwdriver is normal.(For pneumatic screwdriver only)

(4-1) Check the electric screwdriver is normal. (For electric screwdriver only)

Push-start type:

The driver should rotate when the bit is pressed against a flat surface while the Y-pipe is

compressed. Check for any abnormal sounds during rotation.

Lever-start type:

The driver should rotate after pressing lever. Check for any abnormal sounds during

rotation.

(5) Check whether torque setting of pneumatic (elec.)is proper or not.

Fit the driver tip over the hole of screw to be tightened a perform test fastening.

The screw is driven into the hole when the driver bit is pressed against the screw.

Check that the screw is fastened to the specified torque.

Please refer to page 14 ”Torque adjustment” for pneumatic screwdriver

Please refer to page 14”Torque adjustment” for electric screwdriver.

Make sure that the driver is vertical to the work surface and the delivery hose is free of twists

and bent.

Check screw feeding Check Rotating

3. Normal Operation

(1) After all preparatory steps have been competed, load mass screw into the hopper.

(2) Turn power switch on

Load mass screws Turn power switch

(3) Hold the driver unit and press the Y-pipe manually to confirm that a screw is seen at the

tip of the driver at the first time.

(4) Align the screw at the driver tip vertically with the screw hole of the work-piece.

(5) Then, repeat the steps to tighten subsequent screw.

(6)

Operation Demonstration Vertical direction

4. After Operation:

(1) Lubrication(For pneumatic screwdriver only)

Oil flow of 3 to 5 drops through the window, retighten the needle valve. Then, idle the

driver unit alone for one or two minutes to allow oil to circulate.

Lubricate

(2)Turn power switch off after completing operations.

5. Maintenance:

(1) Cleaning hopper interior

Clean the hopper interior once a week. Remove any remaining screw and dust. If the

interior is extremely dirty, wipe thoroughly with a clean.

(2) Check air unit：Check that oil level is between the top and bottom marks.

Supply oil if oil is running low.

(Only pneumatic screwdriver needs oil; elec. screwdriver didn’t need lubricate.)

Lubricate Supply oil

(3) Drain the water which is accumulated in filter..

(4) BIT Replacement(For pneumatic screwdriver only)

To release the nut，disassembly pipe cover, pipe spring, Y pipe.

Use a negative driver and push the ring forward. Keep pushing the ring forward and

pull the bit out. And, still keep pushing the ring forward and insert the new BIT.

Lubricate and assembly it.

ReleaseNut

isassembly pipe cover, pipe spring, Y

pipe

Drain water

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Sumake Utensili

Sumake

Sumake ST-2510 Manuale utente

Sumake

Sumake ST-P6634S Manuale utente

Sumake

Sumake ST-2401SL Manuale utente

Sumake

Sumake ST-2320/R Specifiche

Sumake

Sumake SMPRF48/O.E. Manuale utente

Sumake

Sumake ST-2561 Manuale utente

Sumake

Sumake ST-2516 Manuale utente

Sumake

Sumake ST-2310/RH Manuale utente

Sumake

Sumake STT-08B Manuale utente

Sumake

Sumake HR-0181 Manuale utente

Sumake

Sumake HR3 Series Manuale utente

Sumake

Sumake ST-CH314R Manuale utente

Sumake

Sumake ST-2002A Manuale utente

Sumake

Sumake ST-2280L Manuale utente

Sumake

Sumake ST-2560 Manuale utente

Sumake

Sumake SA-4013 Manuale utente

Sumake

Sumake STH-12A Manuale utente

Sumake

Sumake HR3 Series Manuale utente

Sumake

Sumake PN-5332P Manuale utente

Sumake

Sumake ST-TB100 Manuale utente

Sumake

Sumake SA-CL110 Manuale utente

Sumake

Sumake ST-2237/R Manuale utente

Sumake

Sumake ST-P6634SA Manuale utente

Sumake

Sumake ST-66413 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare