Surewerx ITC IAR-3850 Manuale utente

Operation MANUAL

Air/Water Hose Reel

Prod. No. 028283

Mod. No. IAR-3850

WARNING

Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other

basic safety precautions may result in serious personal injury.

Save these instructions in a safe place and on hand so that they can be read when required. Keep these

instructions to assist in future servicing.

TECHNICAL DETAILS

ITEM MAX PRESSURE HOSE WORKING

TEMPERATURE (°C/°F)

HOSE CAPACITY

MATERIAL I.D. (inch/mm) LENGTH (m/ft)

028283 300Psi (20Bar) -10 – 60°C (14 – 140°F) Hybrid Polymer 3/8"/10 15/50

SAFETY PRECAUTIONS

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all

possible conditions or situations that could occur. It must be understood by the operator that

common sense and caution are factors which cannot be built into this product but must be

supplied by the operator.

HOSE REEL SAFETY PRECAUTIONS

1. Use proper eye protection when assembling and using the hose reel.

2. Keep children away from the work area.

3. Personal injury and/or equipment damage may result if proper safety precautions are not observed.

4. Ensure that reel is properly installed before connecting input and output hoses.

5. Bleed fluid/gas pressure from system before servicing reel.

6. Before connecting reel to supply line ensure that pressure does not exceed maximum working

pressure rating of reel.

7. Remember, even low pressure is very dangerous and can cause personal injury or death.

8. If a leak occurs in the hose or reel, remove system pressure immediately.

9. Ensure that reel, hose, and equipment being service are properly grounded.

10. If reel ceases to unwind or rewind, remove system pressure immediately.

11. Do not pull or jerk on hose.

WARNING:

Exposure of skin directly to pressurized air or fluids could result in severe bodily injury.

INSTALLATION

1. Prior to mounting the hose reel, ensure that the supply line pressure does not exceed the maximum working

pressure of the hose reel.

2. Unpack and inspect reel for damage. Turn by hand to check for smooth operation. Check for completeness.

3. For overhead ceiling mounting: Install reel at most 10 ft/3 m above the floor.

4. You will need to purchase appropriate hardware for mounting your new reel.

i) The reel base has three 8.5 mm drilled holes for mounting on a suitable flat surface.

ii) Using the three holes in the base, mount the reel in the desired location. Be sure to use appropriate hardware

and tighten securely.

5. Apply Teflon tape or pipe sealant to supply line threads, attach to reel inlet and tighten. The other end of incoming

line can now be connected to desired supply source.

6. Apply Teflon tape or pipe sealant to outlet fitting on reel hose, then attach to desired tool or nozzle. Check

connection for leakage, also check hose reel for correct operation. See: Operation section.

7. If hose stopper adjustment is required, pull hose from reel and allow to latch at desired length. Loosen stopper

bolts and slide stopper to a position close to the hose guide. Tighten stopper bolts and unlatch the reel.

8. Double adjustment function: see the picture below. Adjusting the latch spring to left position can lock the

hose at any desired length. Adjust the latch spring to opposite position for a non-lock function, then hose

can be freely moved.

OPERATION

1. Check reel for correct operation by slowly pulling out hose. A clicking noise will be heard every half revolution

of the drum.

2. To latch the reel, pull out the hose and allow it to retract after hearing the first, second, or third click.

3. To unlatch, slowly pull out the hose until the clicking noise stops, then let hose retract until the hose stopper rests

against the hose guide.

4. If necessary, adjust spring tension on reel by adding or removing wraps of hose from spool, one wrap at a time,

until desired tension is obtained. Add wraps to increase tension. Remove wraps to decrease tension.

WARNING:

Do not open the cover (#10) at will. It is very dangerous and can cause personal injury or death.

See picture below.

Don’t Open!

MAINTENANCE

1. Make sure the hose is in proper working order.

2. Clean the hose with a cloth dipped in warm water to remove dirt or deposits and ensure correct rewinding.

3. Do not use detergents or solvents which could prove incompatible with cable-winder materials.

4. Dismantling of the unit by unskilled personal could prove hazardous; the risks involved mainly concern the

preloaded springs.

LIMITED WARRANTY

1. The manufacturer warrants this hose reel against defects in material and craftsmanship, for a period of 24 months

from date of purchase, but not including hose and O-ring parts.

2. Manufacturer’s liability is limited to replacement or repair of defective material within the warranty period, when

returned freight prepaid to the distributor or their designated service depot.

3. The warranty does not cover damage caused by accident, misuse, or faulty installation.

4. The reel must be installed and maintained in compliance with the instructions.

WARNING

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment,

such as those dust masks that are specially designed to filter out microscopic particles.

EXPLODED AND PARTS LIST

REF NO. DESCRIPTION QTY. REF NO. DESCRIPTION QTY.

1 Bushing 1 20 Screw 3

2 Swivel Body 1 21 Screw 3

3 Swivel Spool 1 22 Connector 1

4 O-ring 1 23 Screw 6

5 O-ring 2 24 Pin 2

6 O-ring 1 25 Ratchet Spring 1

7 Small Left Cover 1 26 Screw 1

8 Left Cover 1 27 Ratchet Paw 1

9 Right Cover 1 28 Ratchet Base 1

10 Small Right Cover 1 29 Screw 7

11 Main Spring 1 30 Drum 1

12 O-ring 4 31 Screw 14

13 Axle 1 32 Roller 2

14 Retainer 1 33 Stopper Assembly 1

15 Retainer Base 1 34 Hose Assembly 1

16 Clamp 2 35 Protector Cap 2

17 Lead-in Hose Assembly 1 36 Screw 3

18 Screw 4 37 Screw 4

19 Bracket 1

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare