Texas Instruments CC2533EMK Manuale utente

SWRU253A

October 2013

CC2533EMK Quick Start Guide

1. Kit Contents

2 x CC2533EM with PCB antennas

2 x Pulse W1010 2.4 GHz antennas

Documentation

The RF boards in this kit are FCC and IC certified

and tested to comply with ETSI/R&TTE standards

over temperature from 0 to +35°C. The antenna,

W1010 from Pulse, is a ¼ wave dipole antenna

with 2 dBi gain.

FCC/IC Regulatory Compliance

FCC Part 15 Class A Compliant

IC ICES-003 Class A Compliant

2. Plug EM into SmartRF05EB

In order to run the pre-programmed packet

error rate test on the device, you need 2

SmartRF05 Evaluation Boards. The

SmartRF05EB is included in the CC2533

Development Kit Error! Reference source

not found..

Note that you DO NOT need the SMA

antenna, as the PCB antenna is used by

default.

3. Power Options

There are several ways of applying power

to the SmartRF05EB;

USB (5V through USB plug)

External Power Supply

(requirements below)

2 x 1.5V AA Non-Rechargeable Alkaline

Batteries

Voltage regulators on the SmartRF05EB

will set the on-board voltage to 3.3V.

External Power Supply1Requirements:

Nom Voltage: 4 to 20 VDC

Max Current: 1500 mA

Efficiency Level V

Warning! To minimize risk of personal

injury or property damage, never use

rechargeable batteries to power the board.

4. Select Power Source

Locate the

power source

header P11

just above the

LCD on the

SmartRF05EB

Connect pins 1 and 2 if you are using

batteries to power the board. Connect pins

2 and 3 if you are using USB or external

power supply.

Once you have

set P11, find

switch P8 just

next to the DC

jack on the

SmartRF05EB.

To power on

the board, flip the switch from “OFF” to

“ON”.

4. Packet Error Rate (PER)

When power is applied to the

SmartRF05EB, the preprogrammed PER

test on the CC2533 will start running.

The LCD will display the screen as shown

in the picture above. The number in the

parentheses is the revision of the CC2533.

Press Button 1 to

continue.

5. Select Channel

Select one of the 16 IEEE 802.15.4

channels, with channel number from 11 to

26 (2405-2480 MHz, 5 MHz channel

spacing). Select the same channel for both

boards.

The channel number is increased by

moving the joystick in any direction.

Press Button 1 to confirm the selection.

6 Set up the Receiver

Set one of the boards to operate as

receiver. Use the joystick to select mode.

Confirm by pressing Button 1.

The receiver will now wait for packets from

the transmitter.

7. Set up the Transmitter

Set the other board to operate as

transmitter. Use the joystick to select mode.

Confirm the selection by pressing Button 1.

On the transmitter node, additional

parameters have to be set. On the next

screen, select the TX output power (signal

strength). Use the joystick to select

between -3 dBm, 0 dBm, 4.5 dBm or 7

dBm. Confirm the selection with Button 1.

8. TX: Packets and Packet Rate

Next, select burst size (number of packets

to send) by using the joystick, either 1000,

10K, 100K or 1M packets. Confirm the

selection with Button 1.

After selecting burst size, select packet

rate; 100, 50, 20 or 10 packet per second.

Confirm the selection with Button 1.

When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional

product regulatory and safety certification requirements such as UL, CSA, VDE, CCC, and PSE.

SWRU253A

October 2013

9. TX: Start PER Test

The transmitter is now configured for the

PER test. The PER test is started and

stopped by moving the joystick (in any

direction). The transmitter will display the

number of packets sent during the PER

test.

After stopping the test, it will start from the

beginning if the test is restarted.

10. RX: Observe PER

The PER test receiver will display the PER

value (number of lost and erroneous

packets divided by the number of packets

sent, displayed as a fraction of 1000).

The receiver will also display the number of

received packets and an average RSSI

value based on the last 32 packets.

By pressing button 1, all counters on the

receiver will be reset and the receiver will

restart the PER calculations.

11. SmartRF Studio

After running the PER test, the next

recommended step is to install SmartRF

Studio and to connect the evaluation board

to the PC.

When installing SmartRF Studio, you will

also install the USB drivers required for

Studio and other tools to communicate with

the radio and the SmartRF05EB board.

SmartRF Studio can be used for RF testing

and evaluation of C2533

SmartRF Studio can be downloaded from

www.ti.com/smartrfstudio.

12. Flash Programmer

Texas Instruments has a simple tool which

can be used to program the flash on the

CC2533.

The Flash Programmer application,

available on the kit web page [2], can be

used to program Intel HEX files, read the

contents of flash and several other

operations.

Programming of a CC2533 can be done

with a SmartRF05EB or a CC Debugger.

Production programming tools are available

from TI’s developer network [4].

13. IAR Embedded Workbench

To develop software, program and debug

the CC2533, you should use IAR

Embedded Workbench for 8051.

A free, code size limited version can be

downloaded from the web. See

www.iar.com/ew8051.

14. Packet Sniffer

In order to debug RF protocols, it is

possible to use TI’s SmartRF Packet

Sniffer.

You can use a CC2531 USB dongle or the

SmartRF05EB with a CC2530EM to

capture packets.

A. Available Software

CC2533 Software Examples

Source code for the PER test and other

simple examples for the CC2533 [1].

RemoTI™ Network Protocol

TIs’ implementation of the ZigBee RF4CE

standard: www.ti.com/remoti

TIMAC Software

TI’s IEEE 802.15.4 medium-access-control

stack: www.ti.com/timac

B. More information

On Texas Instruments’ Low-Power RF web

site you will find all our latest products,

application and design notes, FAQ section,

news and events updates, and much more.

Just go to www.ti.com/lprf

The Low Power RF Online Community has

forums, blogs and videos. Use the forums

to find information, discuss and get help

with your design. Join us at

www.ti.com/lprf-forum

The TI LPRF eNewsletter keeps you up to

date on e.g. new products, application

notes, software and events. Sign up at

www.ti.com/lprfnewsletter

C. References

[1] CC2533 product web page

http://www.ti.com/product/cc2533

[2] CC2533EMK kit web page

http://www.ti.com/tool/cc2533emk

[3] CC2533DK kit web page

http://www.ti.com/tool/cc2533dk

[4] LPRF Developer’s Network

http://focus.ti.com/general/docs/gencontent.

tsp?contentId=98994

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims

arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from

the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO

BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH

ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This

notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety

programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or

combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and

therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,

software performance, or infringement of patents or services described herein.

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal

Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,

DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer

use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing

devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency

interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will

be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and

power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local

laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this

radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and

unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory

authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum

permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de

l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain

maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à

l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel

d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans

cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

SPACER

【【Important Notice for Users of EVMs for RF Products in Japan】】

This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:

1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and

Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of

Japan,

2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this

product, or

3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with

respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note

that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.

Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan

http://www.tij.co.jp

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】

本開発キットは技術基準適合証明を受けておりません。

本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。

1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。

2. 実験局の免許を取得後ご使用いただく。

3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。

　　　上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。

日本テキサス・インスツルメンツ株式会社

東京都新宿区西新宿６丁目２４番１号

西新宿三井ビル

http://www.tij.co.jp

SPACER

EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished

electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in

laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks

associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end

product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug

Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,

affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable

regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,

contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)

between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to

minimize the risk of electrical shock hazard.

3. Since the EVM is not a completed product, it may not meet all applicable regulatory and safety compliance standards (such as UL,

CSA, VDE, CE, RoHS and WEEE) which may normally be associated with similar items. You assume full responsibility to determine

and/or assure compliance with any such standards and related certifications as may be applicable. You will employ reasonable

safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to

perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the

user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and

environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact

a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the

specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or

interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the

load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures

greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include

but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the

EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please

be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable

in electronic measurement and diagnostics normally found in development environments should use these EVMs.

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives

harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in

connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims

arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such

as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices

which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate

Assurance and Indemnity Agreement.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Indice

Altri manuali Texas Instruments Microcontrollore

Texas Instruments

Texas Instruments TMS570LS0 32 Series Manuale utente

Texas Instruments

Texas Instruments 430BOOST-TMP006 BoosterPack Manuale utente

Texas Instruments

Texas Instruments CC3235MODSF SimpleLink Manuale utente

Texas Instruments

Texas Instruments Stellaris LM3S9B96 Manuale utente

Texas Instruments

Texas Instruments LM26EVM Manuale utente

Texas Instruments

Texas Instruments MSP430 series Manuale utente

Texas Instruments

Texas Instruments MSP430FG6626 Manuale utente

Texas Instruments

Texas Instruments CC2530-CC2592EM Manuale utente

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuale utente

Texas Instruments

Texas Instruments LaunchPad CC1354P10-6 Manuale utente

Texas Instruments

Texas Instruments Concerto F28M35 Series Manuale del prodotto

Texas Instruments

Texas Instruments Errata MSP430F6746 Manuale utente

Texas Instruments

Texas Instruments TLC2543 Manuale utente

Texas Instruments

Texas Instruments LaunchPad C2000 F280015 Series Manuale utente

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuale utente

Texas Instruments

Texas Instruments TMS570LC43x Manuale utente

Texas Instruments

Texas Instruments LaunchPad MSP430FR2476 Manuale utente

Texas Instruments

Texas Instruments SimpleLink CC2650STK Manuale utente

Texas Instruments

Texas Instruments Hercules RM48 Manuale utente

Texas Instruments

Texas Instruments CC1110-CC1111DK Manuale utente

Texas Instruments

Texas Instruments DA8xx EVM PSP Manuale utente

Texas Instruments

Texas Instruments CC11 L Series Manuale utente

Texas Instruments

Texas Instruments PurePath CC85XXDK-HEADSET Manuale utente

Texas Instruments

Texas Instruments MSP430F67761 Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente

Silicon Laboratories

Silicon Laboratories C8051F800 Manuale utente

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuale utente

Mikroe

Mikroe click Proximity 2 Manuale utente