Textron GREENLINE 910FS Guida alla configurazione
Precautions when cleaning the 910FS and the 910CL
1. Turn off splicer.
2. Use only lint free cotton swabs.
3. Use only 99% pure isopropyl alcohol or an approved substitute.
4. Do not touch the electrodes.
5. Never use compressed air.
6. Use the cleaning brush only to clean debris from general working area, never on the lenses,
V-grooves or mirrors.
Cleaning V-grooves (Recommended Daily)
Refer to Figure 1.
Clean the bottom of the V-groove with an isopropyl alcohol impregnated lint free cotton swab.
Remove excess alcohol from the V-groove with a clean dry lint free cotton swab.
Figure 1 Figure 2
If the contaminants in the V-groove cannot be removed with an alcohol-impregnated lint free cotton
swab, use a cleaved fiber end-face to dislodge contaminants from the bottom of the V-groove.
Refer to Figure 2. Repeat cleaning the V-grooves as in Figure 1.
Cleaning Fiber Clamps (Recommended Daily)
Refer to Figure 3.
If contaminants are present on the clamps, proper clamping may not occur, resulting in poor quality
Alcohol
Tampons
V-groove
V-groove
The Striped
Fiber
Cleaning swab
V-grooves V-grooves
Cleaved Fiber
910FS Fusion Splicer
Cleaning VER 1.0
splices. The fiber clamps should be frequently inspected and periodically cleaned during normal
operation. To clean the fiber clamps do the following:
Clean the surface of the clamps with an alcohol-impregnated lint free cotton swab. Remove excess
alcohol from the clamps with a clean dry lint free cotton swab.
Cleaning Wind Protector Mirrors (Recommended Daily)
Refer to Figure 3.
If the wind protector mirrors become dirty, the fiber core position may be incorrect due to
decreased optical path clarity, resulting in higher splice loss. To clean the mirror’s, do the following.
a) Clean the mirror surface with an alcohol-impregnated thin lint free cotton swab. Remove
excess alcohol from the mirror surface with a clean, dry lint free cotton swab.
b) Mirror should look clean with no streaks or smudges.
Figure 3
Cleaning Objective Lenses (Recommended Weekly)
Refer to Figure 4
If the objective lens’s surface becomes dirty, normal observation of the core position may be
incorrect, resulting in higher splice loss or poor splicer operation. Therefore, clean both of them at
regular intervals. Otherwise, dirt may accumulate and become impossible to remove. To clean the
objective lenses do the following:
a) Before cleaning the objective lenses, always turn off the splicer.
b) Gently clean the lenses’ (X-axis and Y-axis) surface with a dry lint free cotton swab. Using
the swab, start at the center of the lens and move the swab in a circular motion until you
spiral out to the edge of the lens surface.
c) The lens surface should be clean and free of streaks or smudges.
Fiber Clamp
Chips
Wind Shield
Mirrors
Wind Shield
Mirrors
Fiber Clamps
d) Turn on the power and make sure no smudges or streaks are visible on the monitor screen.
Press X/Y key to change the screen and check the state of the lens surface on both the X-
and Y-screens.
Figure 4
NOTE:
•Do not touch the electrodes when cleaning.
It is recommended to clean the objective lenses when replacing the electrodes.
General Fusion Splicer Cleaning (Recommended Daily)
a) Use the cleaning brush only to clean debris from general working area, never on the lenses,
V-grooves or mirrors.
b) Periodically clean the fiber adapters with isopropyl alcohol and a lint free cotton swab.
Never touch the fiber clamping area of the fiber adapters.
Objective Lenses
Cleaning Fiber Cleaver 910CL (Recommended Daily)
Refer to Figure 5.
If the circular blade or clamp pads of the fiber cleaver become contaminated, the cleaving quality
could degrade. This may lead to fiber surface or end-face contamination, resulting in higher splice
loss. Clean the circular cleaving blade and clamp pads with a lint free cotton swab soaked with
isopropyl alcohol.
Figure 5
Fiber Clamps (5)
Cleaving Blade
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Textron Utensili
Textron
Textron Klauke K 105/1 Manuale utente
Textron
Textron Klauke Multi PK60UNV Manuale utente
Textron
Textron EZGO 610987 Manuale utente
Textron
Textron Greenlee 1731 Manuale utente
Textron
Textron Klauke Mini+ ESB 15-L Manuale utente
Textron
Textron Greenlee 441 Series Manuale utente
Textron
Textron Cessna 182S Guida rapida
Textron
Textron GREENLEE 7646 Manuale utente
Textron
Textron Greenlee 915FS Manuale utente
Textron
Textron Greenlee GREG2090 Manuale utente
Textron
Textron Klauke ESM 25CL Manuale utente
Textron
Textron GREENLEE K05-1GL Manuale utente
Textron
Textron Klauke PK 120U Manuale utente
Textron
Textron Greenlee GTSD-1930 Manuale utente
Textron
Textron GREENLEE 39106 Manuale utente
Textron
Textron Greenlee JRF-4EPR Manuale utente
Textron
Textron Greenlee Gator E12CCXLX Manuale utente
Textron
Textron Greenline 45677 Manuale utente
Textron
Textron Greenlee Ultra Tugger 6800 Manuale utente
