TRENDnet TEG-S081Fi Manuale utente

Introduction

The TEG-S081Fi Switch is compact desktop size switches which are

ideal solutions for Fiber network infrastructure. It provides wire-speed,

Fast Ethernet switching function that allows high-performance,

low-cost connection. The Switch features a store-and-forward

switching and it can auto-learn and MAC address on an 8K-entry MAC

address table.

Figure 1-1. The TEG-S081Fi Switch

The Switch provides 8 100Mbps Fiber ports and one GBIC slot for

optional GBIC modules.

The fiber ports are 100Base-SC type multi-mode fiber ports support

up to 2kms distance.

With their build-in Web-based Management, managing and

configuring the TEG-S081Fi Switch becomes easier. From cabinet

management to port-level control and monitoring, you can visually

configure and manage your network via Web Browser. Just click your

mouse instead of typing command strings. However, the TEG-S081Fi

Switch can also be managed via Telnet, Console, or SNMP

Management.

Features

Conforms to IEEE802.3u, IEEE802.3z and IEEE802.3x

Ethernet Standards

8x 100Base-FX SC Type Fiber ports and one GBIC slot

One Console port on the front side for switch Configuration

Half-duplex mode for backpressure, and Full-duplex for flow

control

Store-and-forward switching architecture

Automatic address learning, address migration

8K-entry MAC address table

2Mbits memory buffer sharing

Performs non-blocking full wire speed

LED-indicators for Power, LNK/ACT, FDX/COL,

LNK/ACT(GBIC)

19-inch Rack-Mount size design

Intelligent Management Features

Web-based management

SNMP network management

Console and Telnet management

Port Base VLAN and IEEE 802.1q Tag VLAN, and VLAN

group up to 256 , VLAN ID up to 4K

IEEE 802.3 ad port trunk with LACP (Link Aggregation

Control protocol) supported

IEEE 802.1d Spanning Tree

MIB II (RFC 1213) supported

IP Multi-cast, IGMP Snooping, up to 256 IGMP groups

Support Quality of Service (system provides 8 levels) and

Class of service (per port Hi/Low Queue)

Port Mirror, Broadcast Filter, Static MAC Address filtering,

Port Security and GVRP supported

PackageContents

Unpack the contents of the TEG-S081Fi Switch and verify them against

the checklist below.

Switch

Power Cord

Four Rubber Feet

RS-232 cable

User Guide

TEG-S081Fi Switch Power Cord

Rubber Feet RS-232 cable User Guide

Figure 1-2. Package Contents

Compare the contents of your TEG-S081Fi switch package with the

standard checklist above. IF any item is missing or damaged, please

contact your local dealer for service.

Management Methods

The 8port Fiber Management Switch series supports following

management methods:

Console and Telnet Management

Web-based Management

SNMP Network Management

Console and Telnet Management

Console Management is done through the RS-232 Console Port.

Managing the TEG-S081Fi Switch in this method requires a direct

connection between PC and the TEG-S081Fi Switch. While Telnet

management is done over the network. Once the TEG-S081Fi Switch

is on the network, you can use Telnet to Log in and change the

configuration.

Web-based Management

The Switch provides an embedded HTML web site residing in flash

memory. It offers advanced management features and allow users to

manage the TEG-S081Fi Switch from anywhere on the network

through a standard browser such as Microsoft Internet Explorer.

SNMP Network Management

SNMP (Simple Network Management Protocol ) provides a

means to monitor and control network device, and to manage

configurations, statistic collection, performance, and security.

Hardware Description

FrontPanel

The Front Panel of the Fiber Management Switch series consist of 8x

100Mbps Fast Ethernet Fiber and GBIC ports, and the LED indicators

are also located on the frond panel of the switch.

Figure 2-1. The Front Panel of the Fiber Management Switch

Console Port : Console management can be done through the

Console Port. It requires a direct connection between the Switch and

an end station (PC ) via a RS-232 cable.

Figure 2-2. The Front Panel of the TEG-S081Fi Switch with SC

connector

100Base-FX Fiber Port: There are 2 types of fiber

connectors available for the TEG-S081Fi Switchas shown

above. The distance for fiber cabling can be extended up to 2

kilometers.

Console Port

Baud Rate: 9600,N,8,1

GBIC port : It only support 3.3V model Gigabit Transceiver

for Gigabit SX or LX.

LEDIndicators

Figure 2-3. LED Indicators

There are three LED-Indicators (LNK/ACT, FDX/COL ) for each Fiber

port. The following table provides descriptions of the LED statuses

and meaning. They provide a real-time indication of systematic

operation status.

LED Status Color Description

Power On Green Power On

On Green The port is successfully connecting

with the device on 100Mbps.

Blinks Green The port is receiving or transmitting

data.

LNK /

ACT

Off No device attached.

On Orange The port is operating in Full-duplex

mode and device is attached.

Blinks Orange Collision of Packets occurs in the port.

FDX /

COL

Off

Half-duplex mode or no device

attached.

Table 2-1. The description of LED Indicator

Rear Panel

The Console port and 3-pronged power plug are located at the Rear

Panel of the TEG-S081Fi Switch as shown in Figure 2-8. The

Switches will work with AC in the range 100-240V AC, 50-60Hz.

Figure 2-7 The Rear Panel of the 8 Port 100Mbps Fiber plus one

GBIC Management Switch

Desktop Installation

Set the switch on a sufficiently large flat space with a power outlet

nearby. The surface where you put your Switch should be clean,

smooth, level, and sturdy.

Make sure there is enough clearance around the Switch to allow

attachment of cables, power cord and air circulation.

Power On

Connect the power cord to the power socket on the rear panel of the

Switch. The other side of power cord connects to the power outlet.

The internal power supply in the Switch works with AC in the voltage

range 100-240VAC, frequency 50~60Hz.

Check the power indicator on the front panel to see if power is

properly supplied.

Power on/off switch

AC Power Plug Socket

Network Application

This section provides you a few samples of network topology in which

the Switch is used. In general, the TEG-S081Fi Switch is designed to

be used as a desktop or segment switch.

SegmentApplication

For enterprise networks where large data broadcast are constantly

processed, this switch is suitable for department user to connect to the

corporate backbone.

Figure 3-2 Segment Application

You can use the TEG-S081Fi Switch to connect PCs, workstations,

and servers to each other by connecting these devices directly to the

Switch. All the devices in this network can communicate with each

other. Connecting servers to the backbone switch allow other users to

access the server’s data.

The Switch automatically learns node address, which are

subsequently used to filter and forward all traffic based on the

destination address. You can use any of the Fiber port of the Fiber

Management Switch to connect with another Switch or Hub to

interconnect each of your small switched workgroups to form a larger

and long distance switched network.

Figure 3-3 Use fiber port (TEG-S081Fi Switch) to extend the distance

between workgroups

Altri manuali per TEG-S081Fi

Indice

Altri manuali TRENDnet Interruttore

TRENDnet

TRENDnet TPE-1020WS Manuale utente

TRENDnet

TRENDnet TEG-S224 - DATA SHEETS Manuale utente

TRENDnet

TRENDnet TEG-S5g - Gigabit GREENnet Switch Manuale utente

TRENDnet

TRENDnet TE100-S32plus Manuale utente

TRENDnet

TRENDnet TEG-30284 Manuale utente

TRENDnet

TRENDnet TEG-S16R - DATA SHEETS Manuale utente

TRENDnet

TRENDnet TEG-S80g - Switch Manuale utente

TRENDnet

TRENDnet TEG-S5 Manuale utente

TRENDnet

TRENDnet TEG-S40TXE Manuale utente

TRENDnet

TRENDnet TEG-160WS Manuale utente

TRENDnet

TRENDnet TK-200K Manuale utente

TRENDnet

TRENDnet TEG-S80TXE - Copper Gigabit Switch Manuale utente

TRENDnet

TRENDnet TE100-S24V Manuale utente

TRENDnet

TRENDnet TE100S8P - Fast Ethernet Switch Manuale utente

TRENDnet

TRENDnet TEG-S240TX - DATA SHEETS Manuale utente

TRENDnet

TRENDnet TU-400 Manuale utente

TRENDnet

TRENDnet TEG-S81g Manuale utente

TRENDnet

TRENDnet TEG-424WS Manuale utente

TRENDnet

TRENDnet TI-G102i Manuale utente

TRENDnet

TRENDnet TK-207K - KVM Switch - USB Manuale utente

TRENDnet

TRENDnet TE-910plus Manuale utente

TRENDnet

TRENDnet TEG-224WSplus Manuale utente

TRENDnet

TRENDnet TEG-S224TXA - 26PORT Gigabit Copper Switch 24-10/100... Manuale utente

TRENDnet

TRENDnet TK-217i Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente