TRENDnet TEG-S80TXD Manuale utente
TEG-S80TXD
Version 10.18.2005
User’s Guide
Copyright ©2005. All Rights Reserved. TRENDnet.
Table of Contents
English ............................................................................................
Românǎ ..........................................................................................
1
8
1
8
2
9
6
13
15
1. Introduction .............................................................................
2. Unpacking and Setup ..............................................................
3. Identifying External Components ............................................
1. Introducere ..............................................................................
2. Despachetare si instalare .......................................................
3. Identificarea componentelor externe .......................................
Technical Specifications ..................................................................
This section describes the features of the 8-Port 10/100/1000Mbps Gigabit
Ethernet Switch.
Features
The 8-Port 10/100/1000Mbps Gigabit Ethernet Switch was designed for easy
installation and high performance in an environment where traffic on the
network and the number of users increase continuously.
1
1. Introduction
English UG
English
8 x 10/100/1000Mbps Auto-negotiation Gigabit Ethernet ports
Auto-MDIX for each port
Supports Full/Half duplex transfer mode for 10 and 100Mbps
Supports Full duplex transfer mode for 1000Mbps
Wire speed reception and transmission
Store-and-Forward switching method
Supports 8K entries absolute MAC address table
Supports 256K Bytes RAM for data buffering
Extensive front-panel diagnostic LEDs
IEEE 802.3x flow control for full-duplex
Back pressure flow control for half-duplex
Optional Rack-mount Kit for 19” standard rack
2English
2. Unpacking and Setup
This chapter provides unpacking and setup information for the Switch.
Unpacking
Open the shipping carton of the Switch and carefully unpack its contents. The
carton should contain the following items:
If any item is found missing or damaged, please contact your local reseller for
replacement.
TEG-S80TXD
User's Guide
Four rubber feet with
adhesive backing
AC power cord
TEG-S80TXD
Version 10.18.2005
User’s Guide
Copyright ©2005. All Rights Reserved. TRENDnet.
3English
Setup
Desktop Installation
The setup of the Switch can be performed using the following steps:
When installing the Switch on a desktop or shelf, the rubber feet included with
the device must be attached first. Attach these cushioning feet on the bottom at
each corner of the device. Allow enough ventilation space between the device
and the objects around it.
The surface must support at least 5 kg.
The power outlet should be within 1.82 meters (6 feet) of the device.
Visually inspect the power cord and see that it is secured fully to the AC
power connector.
Make sure that there is proper heat dissipation from and adequate
ventilation around the Switch. Do not place heavy objects on the Switch.
Gigabit Ethernet Switch installed on a Desktop or Shelf
4
Rack Installation (optional)
The 8-Port 10/100/1000Mbps Gigabit Ethernet Switch can be mounted in an
EIA standard size, 19-inch rack, which can be placed in a wiring closet with
other equipment. To install, attach the mounting brackets on the Switch's front
panel (one on each side) and secure them with the provided screws.
Then, use the screws provided with the equipment rack to mount the Switch in
the rack.
English
Installing the Switch on an equipment rack
Attaching the mounting brackets to the Switch
5English
Connecting Network Cable
AC Power
The 8-Port 10/100/1000Mbps Gigabit Ethernet Switch supports eight
10/100/1000Mbps Gigabit Ethernet ports. These ports support half or full
duplex mode when running in 10Mbps or 100Mbps. They support full duplex
while running in 1000Mbps.
These ports are Auto-MDIX type port. They can auto transform to MDI-II or
MDI-X medium type, so you can just make an connection with a straight or
crossover cable.
The 8-port Gigabit Ethernet Switch can be used with 100~240V AC, 50~60 Hz
power source. The power supply of the Switch will adjust to the local power
specification automatically and may be turned on without having any or all LAN
segment cables connected.
6English
3. Identifying External Components
The front panel of the Switch consists of eight 1000BASE-T ports and LED
indicators.
This chapter describes the front panel, rear panel and LED indicators of the
Switch
Front Panel
Front panel view of the Switch
Rear panel view of the Switch
Eight Gigabit Ethernet ports of 10/100/1000Mbps Auto-Negotiation
interface.
Comprehensive LED indicators display the conditions of the Switch and
status of the network. A description of these LED indicators follows (see
LED Indicators).
AC Power Connector: This is a three-pronged connector that supports
the power cord. Plug in the female connector of the provided power cord
into this connector, and the male into a power outlet. Supported input
voltages range from 100~240V AC at 50~60 Hz.
Rear Panel
The rear panel of the Switch consists of an AC power connector. The following
figure shows the rear panel of the Switch.
7English
The LED indicators of the Switch including Power, Link/Act, 1000Mbps and
100Mbps. The following shows the LED indicators for the Switch along with
explanation of each indicator.
The Switch LED indicators
LED Indicators
This indicator lights green when the Switch is receiving power. It is off for
no power.
This LED indicator lights green when there is a valid connection (or link) to
the port. The LED indicator blinks whenever there is reception or
transmission (i.e. ActivityAct) of data at a port.
This LED indicator lights green when there is a valid 1000Mbps Gigabit
Ethernet connection (or link) to the port.
This LED indicator lights green when there is a valid connection (or link) to
100Mbps Fast Ethernet device at the port.
Power:
Link/ACT:
1000Mbps:
100Mbps:
If the connection (or link) is 10Mbps, both 1000Mbps and 100Mbps LED
indicators are off.
8
1. Introducere
Românǎ
Românǎ
Aceasta sectiune descrie caracteristicile Switchului cu 8 porturi
10/100/1000Mbps Gigabit Ethernet
Trasaturi
Switchul cu 8 porturi 10/100/1000Mbps Gigabit Ethernet a fost realizat in
vederea unei instalari usoare si unei performante ridicate, intr-un mediu unde
traficul in retea si numarul utilizatorilor sunt intr-o continua.
8 porturi x 10/100/1000Mbps Auto-negociere Gigabit Ethernet
Auto-MDIX pentru fiecare port
Suporta mod de transfer Full/Half duplex pentru 10 si 100Mbps
Suporta mod de transfer Full duplex pentru 1000Mbps
Viteza la nivel de “fir” pentru receptare si transmitere
Metoda switching Store-and-Forward
Suporta intrari 8K table adrese absolute MAC
Supporta 256K Bytes RAM pentru buffering la informatie
LEDuri pentru diagnostic pe panpul frontal
Control al fluxului de tip IEEE 802.3x pentru full-duplex
Control al fluxului de presiune pentru half-duplex
Kit Rack optional pentru rack standard 19” .
Altri manuali per TEG-S80TXD
1
Indice
Lingue:
Altri manuali TRENDnet Interruttore
TRENDnet
TRENDnet TE100-S16Eplus Manuale utente
TRENDnet
TRENDnet TI-RG262i Manuale utente
TRENDnet
TRENDnet TPE-TG44G Manuale utente
TRENDnet
TRENDnet TEG-S2400I - DATA SHEETS Manuale utente
TRENDnet
TRENDnet TEG-160WS Manuale utente
TRENDnet
TRENDnet TE100-S1616V Manuale utente
TRENDnet
TRENDnet TEG-S24Dg Manuale utente
TRENDnet
TRENDnet TK-401R Manuale
TRENDnet
TRENDnet TE100-S24plus Manuale utente
TRENDnet
TRENDnet TEG-S2500i Manuale utente
TRENDnet
TRENDnet TK-200K Manuale utente
TRENDnet
TRENDnet TE100-S5 Manuale utente
TRENDnet
TRENDnet TE-500plus Manuale utente
TRENDnet
TRENDnet TE100 S55Eplus Manuale utente
TRENDnet
TRENDnet TI-PG162 Manuale utente
TRENDnet
TRENDnet TPE-224WS - Web Smart PoE Switch Manuale utente
TRENDnet
TRENDnet TK-208K Manuale utente
TRENDnet
TRENDnet TK-801R Manuale utente
TRENDnet
TRENDnet TK-214i Manuale utente
TRENDnet
TRENDnet TPE-S88 - Web Smart PoE Switch Manuale utente
