Turner Designs AquaFlash Manuale utente

www.turnerdesigns.com

998-8602

Revision A

Page 1 of 2

Quick Start Guide

Congratulations on your new AquaFlash Handheld Active Fluorometer.

We are committed to customer satisfaction. If you need assistance,

technical specialists are available to answer your questions at 408-749-

0994 or toll-free at 877-316-8049. This Quick Start Guide will help you

use the AquaFlash, for more detail please refer to the manual.

Sampling Procedure



proceeding.

1. Fill a glass cuvette ¾ full with the collected sample.

2. Dry and clean all faces of the cuvette using Kim Wipes.

3. Make sure the AquaFlash is on and ready for use. Press READ.

You will be prompted to insert your sample and press READ.

4. Insert the cuvette into your AquaFlash and close the lid.

5. Press READ again and the measurement will begin.

6. Once the measurement is complete, remove the cuvette and discard

the sample.

7. Results displayed will show values for Total Chlorophyll (ug/L) as

CHL, Yield or photosynthetic efficiency as YLD, time sample was

recorded in hours:minutes, and the sample number as a 4 digit value

representing sample numbers from 1 to 1000.

8. Press the down arrow key to view Fo (minimum), Fm (maximum),

and Blank raw fluorescence values.

9. When finished viewing data, or if ready to run the next sample, press

ESC to get to the Home screen and repeat sampling procedure



CHL: 5.25 HH:MM

YLD: 0.54 # 0001

Note: The figure to the left is an example

of results displayed after measuring a

sample.

Fo: 250 Fm: 450

Blank: 50

Viewing Data

Data can be viewed on the Aqua display or downloaded to a computer for

viewing. To view data use the  arrow keys to scroll to a desired sample,

sample number will be displayed in the bottom right corner of the screen. Press

the down arrow key to view raw fluorescence data for that sample.

Refer to the AquaFlash manual for instructions on how to send and view data on

your computer and how to clear logged data from the Aqua memory.



www.turnerdesigns.com

998-8602

Revision A

Page 2 of 2

Quick Start Guide

Adjustable Solid Secondary Standard Procedure

The AquaFlash is factory calibrated and should remain calibrated for many

years. Calibration can be checked using the Solid Secondary Standard (SSS).

Users will first have to set the SSS using the following procedure:

1. Purchase or obtain a SSS.

2. Turn the AquaFlash on using the ON/OFF button and wait until warm up has

completed.

3. Press the CAL VAL button and record the set calibration value.

4. Loosen the small hex screw located on the back of the SSS and then holding

the SSS by the tab, insert it with the tab at the back of the sample

compartment and close the sample compartment lid.

NOTE: The AquaFlash should be on a flat surface when reading the SSS.

5. Press the READ button twice to begin measurement and look at the CHL

reading for the SSS.

a. If the CHL value displayed is lower than the calibration value, adjust the

SSS to give you a larger response by rotating the silver hex screw

located at the top of the SSS counterclockwise and re-read the SSS.

b. If the CHL value displayed is higher than the calibration value, adjust the

SSS to give a smaller response by rotating the silver hex screw located

at the top of the SSS clockwise and re-read the SSS.

6. Continue adjusting and reading the SSS until the CHL value displayed

matches within 5% the calibration value determined in step 3.

7. When finished, tighten the locking screw on the back of the SSS by turning

response.

8. Insert lid.

9. Press the CHK STD button.



repeat steps 3 9 until the SSS is properly adjusted. It is recommended that

users make 5 consecutive measurements of the SSS after it is set to ensure it is

properly adjusted.

The SSS can now be used to periodically check for instrument drift.



Altri manuali per AquaFlash

Indice

Altri manuali Turner Designs Strumento di misura

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs 10-AU Manuale utente

Turner Designs

Turner Designs C-FLUOR Manuale utente

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs Opti-Trace Manuale utente

Turner Designs

Turner Designs TD-20/20 Manuale utente

Turner Designs

Turner Designs 8000 Manuale

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs 10-AU Guida

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs Enviro-T Manuale utente

Turner Designs

Turner Designs AquaFlash Manuale utente

Turner Designs

Turner Designs C-FLUOR Manuale utente

Turner Designs

Turner Designs Little Dipper 2 Manuale utente

Turner Designs

Turner Designs Little Dipper Manuale utente

Turner Designs

Turner Designs TD-4100XD E09 Istruzioni per l'installazione e il funzionamento

Turner Designs

Turner Designs C3 Manuale utente

Turner Designs

Turner Designs Trilogy Manuale utente

Turner Designs

Turner Designs 10-AU Manuale per l'uso e la cura

Turner Designs

Turner Designs AquaFluor Manuale utente

Turner Designs

Turner Designs TD-107 5.0 Manuale utente

Turner Designs

Turner Designs C3 Manuale utente

Turner Designs

Turner Designs FluoroSense Manuale utente

Turner Designs

Turner Designs Opti-Check Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente