Turner Designs C-FLUOR Manuale utente

www.turnerdesigns.com

998-2132

Revision A

Page 1 of 3

Digital C-FLUOR Quick Start Guide

“A”= PTSA“A”= PTSA

“C” = Chlorophyll

“A”= PTSA“A”= PTSA

“C” = Chlorophyll

Congratulations on the purchase of your new Digital C-FLUOR Submersible Probe. We are committed to customer

satisfaction. If you need assistance, technical specialists are available to answer your questions at 408-749-0994 or

toll-free at 877-316-8049. This Quick Start Guide will help you set up your Digital C-FLUOR Submersible Probe and

describe how to take measurements so you can start collecting data as quickly as possible.

Your Digital C-FLUOR Probe is configured for the application that correlates with the identification letter stamped on

the 6-pin bulkhead connector (see list below). For Digital C-FLUOR Probes that do not have a connector, the

identification letter will be etched on the body next to the part number.

“C” = Chlorophyll “R” = Rhodamine WT

“F” = Fluorescein “P” = Phycocyanin

“E” = Phycoerythrin “U” = CDOM / fDOM

“O” = Crude Oil “B” = Optical Brighteners

“T” = Turbidity “D” = Red Excitation

Initial Connections

Note: Supply voltages greater than 15 VDC will damage the probe.

Use the wiring guide below to connect the Digital C-FLUOR to your data logger or third-party system.

NOTE: If you purchased the Programming Kit P/N 2120-900 and prefer to use software to set

up the Digital C-FLUOR, see Section 

Use the communication protocol below to set up communication with your DigitalC-FLUOR.

Baud Rate: 9600 (default)

NOTE: If the baud rate was manually changed, please use the manually set baud rate for

communication.

Data bits: 8

Parity: None

Stop bits: 1

Flow Control: None

After configuring the communication settings, supply power to the instrument and see Section .

C-FLUOR

Pins/Wires Pin

Number Function Connection

Red 1 Supply Voltage

3 –15 VDC PSU –Positive Connection

Black 2 Supply Ground, 0VDC PSU –Ground Connection

Orange 3 Receive Data RX

Green 4 Transmit Data TX

Blue 5 Digital Ground GND

Yellow 6 N/A -

www.turnerdesigns.com

998-2132

Revision A

Page 2 of 3

Digital C-FLUOR Quick Start Guide

Using Commands to Communicate with the Digital C-FLUOR

With the C-FLUOR connected and powered make the following functional tests:

1. Is the LED on?

Hold a piece of white paper about ½ an inch in front of the optical head to ensure the LED is ON.

Note: This test does not work for Turbidity probes because they use infrared which is not visible.

2. Using the S06! command, set the Streaming Output Rate to 1 reading per second. Do you see values

being streamed at once per second rate?

3. Does the output change?

Move the light source closer to the piece of paper and check if the output value being streamed increases.

Use commands from the command list below to program and set up your Digital C-FLUOR after successfully

passing all functional tests..

Use the list below to set Streaming Output Rate

Command Name Note

I! Sensor Information For Probe Information

C! Calibration Information For Calibration Values

Bxxxx! Set Baud Rate “xxxx” refers to baud rate

(9600, 14400, 19200, 38400, 57600)

Sxx! Streaming Output Rate Puts probe into streaming mode Use table

below to determine “xx”

P! Polling Mode Puts probe into polling mode

R! Read Command Only when in Polling mode

M! Report the Current Mode Returns S with rate or P

xx Readings per second Seconds between

readings

01 Not Available

02 16

03 8

04 4

05 2

06 1 1 (factory default)

07 2

08 5

09 10

10 15

11 30

12 60

13 120

14 300

15 600

16 1800

17 3600

www.turnerdesigns.com

998-2132

Revision A

Page 3 of 3

Digital C-FLUOR Quick Start Guide

Using Software to Communicate with the Digital C-FLUOR

With the C-FLUOR connected to your computer and power supply, and communicating with the software,

answer questions 1-3 to perform the following functional tests:

1. The LED is on?

Hold a piece of white paper about ½ an inch in front of the optical head to ensure the LED is ON.

Note: This test does not work for Turbidity probes because they use infrared which is not visible.

2. Is there output?

Click the “Get Datapoint” button; if a value is displayed in the box then the instrument’s output is working.

3. Does the output change?

Move the light source closer to the piece of paper and again click the “Get Datapoint” button; if the output

increases then the instrument’s detector is working.

If the instrument passed all functional tests, begin configuring your Digital C-FLUOR Probe using the software.

To program the Digital C-FLUOR Probe using software, connect the probe to your computer using the Digital C-

FLUOR RS-232 Programming Cable P/N 2120-160 and connect the 12 volt power supply P/N 7000-941 to the

Programming Cable’s power jack, then follow the instructions below:

1. Once USB drivers have automatically installed, download and install Digital C-FLUOR’s Software from

www.turnerdesigns.com.

2. After software has successfully installed, double-click the software’s icon which should have been

automatically added to your desktop.

3. Click “Communicate With C-FLUOR” and wait a few minutes for the software to detect the connected

probe.

4. When connected, C-FLUOR Communication Status radio button will change from red to green

12V Power Supply12V Power Supply

RS-232 ProgrammingCable

Altri manuali per C-FLUOR

Altri manuali Turner Designs Strumento di misura

Turner Designs

Turner Designs 10-AU Manuale utente

Turner Designs

Turner Designs TD-4100XD E09 Istruzioni per l'installazione e il funzionamento

Turner Designs

Turner Designs AquaFluor Manuale utente

Turner Designs

Turner Designs FluoroSense Manuale utente

Turner Designs

Turner Designs TD-107 5.0 Manuale utente

Turner Designs

Turner Designs Opti-Trace Manuale utente

Turner Designs

Turner Designs TD-20/20 Manuale utente

Turner Designs

Turner Designs TD-5100 ECA Manuale utente

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs AquaFlash Manuale utente

Turner Designs

Turner Designs AquaFlash Manuale utente

Turner Designs

Turner Designs 8000 Manuale

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs 10-AU Guida

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs FluoroSense Manuale utente

Turner Designs

Turner Designs Opti-Check Manuale utente

Turner Designs

Turner Designs C3 Manuale utente

Turner Designs

Turner Designs Little Dipper Manuale utente

Turner Designs

Turner Designs Trilogy Manuale utente

Turner Designs

Turner Designs C3 Manuale utente

Turner Designs

Turner Designs Ballast-Check 2 Manuale utente

Turner Designs

Turner Designs Enviro-T Manuale utente

Turner Designs

Turner Designs 10-AU Manuale per l'uso e la cura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente