Uplus Lighting 100SPOT Manuale utente

User manual

100 SPOT

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

Technical Specifications…………………………………………………………………………4

Control Menu ……………………………………………………………………………………5-6

DMX Channels …………………………………………………………………………………6-8

Trouble Shooting…………………………………………………………………………………8

Fixture Cleaning………………………………………………………… ………………………9

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also

always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specifications

Input Voltage: 100-240V, 50/60Hz

Power consumption: 120W

Beam angle:8°

Light source: 100W White LED

Pan: 540°(16bit) Electric correction

Tilt：270° (16bit) Electric correction

Beam angle: 1.3°

Gobo:static gobo: 7gobo+open

Rotating gobo:6+open

Prism: 5 prism

Frost effect

Dimming:0-100% linear adjustment

DMX Channels:14 channels

Control mode:DMX512,Auto, Sound active, Master/slave

Dimension:260*200*310 mm; NW: 5.85KGS;GW:6.65KGS

3.Control Menu

set up

option

explain

running mode

DMX

From ver status: receiving DMX signal from control station or host

Go at a

slow pace

Random

walk

sound

control

DMX address

1~512

Press OK to enter the edit status.When selected, press "up" and "down"

keys to change the address code.Press OK again to select the ten

editors.Press OK again to select the single bit edit.Press the Exit Edit Status

once again

channel pattern

Standard

14CH

Standard 14-channel mode

RDM function

open

X reversal

open

Y reversal

open

XY exchange

open

Channel channel for XY axis (including fine tuning)

XY encoder

open

Use the encoder (optical coupling) to judge steps and automatically correct

the position

Correct the position without using the encoder (optical coupling)

There is no DMX

signal

keep

Continue running in the original state

zero

clearing

Motor back, stop operation

Screen protection

open

Turn off the backlight after 30 seconds of idle

Back light forever bright

Restore the default

settings

Press OK to see the confirmation dialog box, and press OK again, to restore

the default settings

System info

option

explain

software release

Current software version

DMX channel value

This enters the subinterface and displays channel values in value and percentage for

viewing

System error record

If the red ERR indicator shines, the lamp is running wrong, and the details can be viewed

into the subinterface.After viewing, press Clear to empty the error record

Note: Sometimes it is not really a Hall or optical coupling installation problem, but a

reverse motor wiring

error message

explain

Motor reset failed,

serial port error

Drive board did not respond.The serial port communication line connecting the display

board and the drive board is faulty, or with the drive board is.

X-axis reset failed

X axis photoelectric switch, or X axis motor problem

The reduction of the

Y axis failed

Y-axis photoelectric switch, or Y-axis motor problem

X-axis Hall error"

Problem with the X-axis Hall

The Y-axis Hall error

There are problems with the Y-axis Hall

Color disk reset

failed

Color disc Hall, or the color disc motor has a problem

Pattern disk reset

failed

Patterned disc Hall, or the patterned disc motor has a problem

The focus reset

failed

Focus Hall, or have problems with the focusing motor

Bulb control failed

bubble or bubble failure, there is a problem with the lighter or bulb

Senior

option

explain

Reset calibration

After entering the sub-interface, the reset position of X-axis and Y-axis motors can be

adjusted to make up for the error in hardware installation. The adjustment range

is-128~ + 127. + 0 indicates no adjustment.

Sensor monitoring

Real-time monitoring of various photoelectric switches, hall and other sensors on the

lamp status

4.DMX Channels

CH14

Function

Value

Effect

Dimmer

000-255

Dimmer from dark to light

Strobe

000-255

Strobe from slow to fast

Pan

000-255

Pan

Tilt

000-255

Tilt

XY speed

000-255

Speed from fast to slow

Color

000 - 004

005 - 009

010 - 014

015 - 019

white

color 1

color 2

color 3

color

020 - 024

025 - 029

030 - 034

035 - 039

040 - 044

045 - 049

050 - 054

055 - 059

060 - 064

065 - 069

070 - 074

075 - 079

080 - 255

color 4

color 5

color 6

color 7

White+color 1

color 1+color 2

color 2+color 3

color 3+color 4

color 4+color 5

color 5+color 6

color 6+color 7

color 7+white

Slow rotation -Fast rotation

GOBO

000-009

010-019

020-029

030-039

040-049

050-059

060-069

070-079

080-128

129

130-134

135

136-220

221-225

……

250-255

White

GOBO1

GOBO2

GOBO3

GOBO4

GOBO5

GOBO6

GOBO7

FAST rotation

Slow rotation

Stop

Slow rotation

FAST rotation

GOBO1 shake,slow to fast

……

GOBO7 shake,slow to fast

Gobo1

000 - 009

010 - 019

020 - 029

030 - 039

040 - 049

050 - 059

060 - 069

070

……

129

130 - 134

135

……

225

226 - 230

……

251 - 255

White

Gobo1

Gobo2

Gobo3

Gobo4

Gobo5

Gobo6

FAST rotation

……

Slow rotation

Stop

Slow rotation

……

FAST rotation

Gobo1 shake,slow to fast

……

Gobo6 shake,slow to fast

GOBO 1 RT

000-063

Position

GOBO 1 RT

……

127

128

……

190

191-192

193

……

255

Slow rotation

……

FAST rotation

……

Slow rotation

Stop

Slow rotation

……

FAST rotation

Prism

000-009

010-014

……

255

Remove the Prism

Insert prism

Prism slow rotation

……

Prism fast rotation

focus

000-255

Pan fine

000 - 255

Pan fine

Tilt fine

000 - 255

Tilt fine

Reset

000-127

128-255

None, there is no action for the area without the specified function

Reset all motors

5.Trouble Shooting

ollo

ing

few

oble

y occu

uring

ope

tion

. He

tion

leshooting

The

does

work

, no

ght

Check

nect

ion of p

owe

eas

ure

ins

volt

Check

pow

LED

responding

LED

on.

che

nectors,

link

ope

If th

nd no

espons

el,

che

ess

etti

s a

ity

nter

ittent

oble

che

ins

onn

ecto

PCB

nit

the

iou

ntroller

Check

or run

lon

volta

les

terfer

ence

inter

face

circui

. One

the

cha

ing

tep

moto

dam

the

nect

to th

PCB

oken.

oto

’

ive

PCB

ndition

6.Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,

smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Indice

Altri manuali Uplus Lighting Attrezzatura di illuminazione

Uplus Lighting

Uplus Lighting IP-Z740 Manuale utente

Uplus Lighting

Uplus Lighting 230 BEAM Manuale utente

Uplus Lighting

Uplus Lighting 37X15ZWASH Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting RETRO 360 Manuale utente

Uplus Lighting

Uplus Lighting 200 LED RETRO Manuale utente

Uplus Lighting

Uplus Lighting 300 MZ-SPOT PR Manuale utente

Uplus Lighting

Uplus Lighting PF350 Manuale utente

Uplus Lighting

Uplus Lighting IP-L360 Manuale utente

Uplus Lighting

Uplus Lighting LED PROFILE MZ Manuale utente

Uplus Lighting

Uplus Lighting BL6 Manuale utente

Uplus Lighting

Uplus Lighting 10X30 COB BAR Manuale utente

Uplus Lighting

Uplus Lighting 3010 IP PAR Manuale utente

Uplus Lighting

Uplus Lighting 200 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting 750 BSWF Manuale utente

Uplus Lighting

Uplus Lighting BR360 Manuale utente

Uplus Lighting

Uplus Lighting 250 BEAM Manuale utente

Uplus Lighting

Uplus Lighting PIXEL IP20X15 BAR Manuale utente

Uplus Lighting

Uplus Lighting 250 LED BEAM Manuale utente

Uplus Lighting

Uplus Lighting 280 LED BSW Manuale utente

Uplus Lighting

Uplus Lighting IP 300Z SPOT-WW Manuale utente

Uplus Lighting

Uplus Lighting 400 IP BLINDER Manuale utente

Uplus Lighting

Uplus Lighting W3725 Manuale utente

Uplus Lighting

Uplus Lighting LED PROFILE FIX Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente