VERITAS D595 Manuale utente

U.S. Des. Pat. No. D595,558

Skew Rabbet Plane

Our Veritas®Skew Rabbet Planes, like the Stanley #289 that inspired them, are

conﬁgured with a full-width blade skewed at a 30° angle that enables the plane to cut

right into a corner of a rabbet. This arrangement, along with an adjustable fence and

a depth stop, allows them to cut accurate rabbets by hand. A scoring cutter enables

cross-grain work by severing the wood ﬁbers ahead of the lapped blade.

Positioning the Blade

Caution: Be aware that the blade is

sharp; careless handling can result in

serious injury.

The position of the blade relative to the plane

body is essential to the correct performance

of any rabbet plane. The cutting edge needs to

be set to the proper projection to achieve the

desired depth of cut and needs to be parallel

to the sole of the plane. To ensure that it cuts

right into the corner of a rabbet, it is critical

that the inside (or leading) edge of the blade

extend just beyond the side of the plane.

Figure 1: Plane components.

Depth Stop

Blade Adjustment

Knob

Rear

Handle

Scoring Blade Lever Cap

Knob

Fence

Depth Stop Knob

Blade

Fence Locking Knob

Blade Set Screws

Front Knob

Lever Cap

Blade corner just

proud of side.

Cutting edge

parallel

to sole.

Figure 2: Blade position.

It is equally important that the remaining edge (or side) of the blade behind the leading

corner does not extend or angle out farther than the tip, as this would prevent the

plane from cutting right into the corner. Note also that, because the blade is skewed,

the outer edge of the blade has been bevelled to prevent it from projecting beyond the

corner of the blade.

The proper blade position is most easily established using the two blade set screws.

First, back off the lever cap knob just enough to free up the blade, and then use your

ﬁnger to shift the blade over against the set screws. While sighting along the sole of

the plane, adjust the set screws until the correct blade position is attained. Once set,

the set screws will allow the blade to be removed from the plane and then returned to its

previously established position.

Depth of Cut

The depth of cut is the amount of material that is removed with each pass of the plane,

typically in the range from 0.005"to 0.020", depending on the hardness of the wood

being cut. Adjust the depth as required, tighten the lever cap knob, and take a test cut in a

scrap piece of wood to conﬁrm setting.

Cutting Rabbets

The size of the rabbet to be cut is controlled by determining the width (A) with the

fence setting and the depth (B) with the depth stop setting.

Setting the Fence

The width of the rabbet is determined

by the fence setting. Loosen the two

fence knobs and slide the fence until the

distance from the face of the fence to the

outside edge of the blade is equal to the

required rabbet width. Retighten the

fence knobs. Maximum width of 11/2"

when using the entire blade.

Figure 4: Setting the fence.

Rabbet Width

Fence

Knob

Figure 3: Rabbet dimensions.

Setting the Depth Stop

The depth of the rabbet is determined by the depth stop setting. To set the depth stop,

loosen the depth stop knob, slide the depth stop to the desired position, and retighten

the knob. Maximum rabbet depth is 3/4". The depth stop and knob can be removed to

permit cutting or cleaning up much deeper rabbets, if desired.

Setting the Scoring Blade

The scoring blade (or nicker) is used when

working across the grain. The circular blade

is attached off-center to an axle, allowing the

cutting depth to be adjusted by rotating the

blade and axle. (It can also be shifted to a neutral

position when it is not required.) To rotate the

axle, you must ﬁrst release the locking screw

that holds it in position; it is located on the other

side of the plane, behind the front knob. Once

the scoring blade is in the desired position,

retighten the locking screw.

The outside (or cutting) edge of the scoring blade must extend just beyond the side

of the plane and be aligned with the corner of the blade. To adjust the scoring blade

relative to the side of the plane, loosen the fence locking knobs and remove the fence.

Unscrew and remove the front fence rod. Loosen the scoring axle locking screw.

Insert a small-slot screwdriver through the front fence rod hole to access a slotted set

screw that establishes the position of the scoring blade relative to the side of the plane.

While pressing the scoring blade and axle in against the set screw, turn the set screw

clockwise or counterclockwise, as required until the scoring blade is positioned just

proud of the side of the plane. Once the position of the scoring blade is established,

retighten the locking screw and reverse the steps to replace the fence rod and fence.

Rabbet Depth

Depth Stop

Knob

Figure 5: Setting the depth stop.

Figure 6: Setting the scoring blade.

Scoring Blade

Auxiliary Fence

For cutting some rabbets, such as one where the depth is much greater than its width,

you can add a larger auxiliary fence to better register the plane to the workpiece.

Simply make a wooden fence, as plain or fancy as you wish, and attach it using wood

screws through the holes in the existing fence. Be sure to use screws that are not so

long that they break through the working face of the wooden fence.

Blade Sharpening

The skew rabbet plane blade has a 22° skew

and is ground with a 30° bevel. The face of

the blade is lapped. Additional sharpening

need only involve honing a small micro-

bevel. Since the blade is installed bevel

down, the cutting angle is determined by the

bed angle; in this case, 45°.

Note: The Veritas Skew Registration Jig

(05M09.03) for use with the Veritas Mk. II

Honing Guide (05M09.01) includes a setting

for 22°.

When sharpening the cutting edge, it is

important to maintain the correct skew

angle. Failure to do so may cause the side

edge of the blade to angle out farther than

the tip, preventing the plane from cutting

right into the corner.

The scoring blade will also need to be

resharpened over time. Remove the securing

screw, then the blade, and lap the face of the

scoring blade on a stone.

Figure 7: Scoring blade position.

Locking Screw

Fence Rod

Scoring

Axle

Set Screw

Side Edge

Figure 9: Blade in cutting position.

22° Skew

30° Bevel

Figure 8: Blade geometry.

Veritas Tools Inc. Ottawa ON K2H 1C2 Canada veritastools.com

Care and Maintenance

The body of this plane is ductile cast iron and comes treated with rust preventative.

Remove this using a rag dampened with mineral spirits. Clean all machined surfaces.

We recommend that you initially, then periodically, apply a light coat of silicone-free

paste wax to seal out moisture and prevent rusting (as well as act as a lubricant for

smoother planing). Wipe off any wood dust from the surfaces that you will be waxing,

apply a light wax coating, let dry, then buff with a clean soft cloth. At the same time,

the solvents in the wax will remove any harmful oils left from your ﬁngers that can

lead to corrosion.

Note: Since the face of the fence and the bottom of the depth stop will come in contact

with the workpiece, it is important to keep these parts coated with paste wax to prevent

marring the workpiece.

If storage conditions are damp or humid, the plane should, in addition to the treatment

outlined above, be wrapped in a cloth or stored in a plane sack. This precaution will

also guard against dings and scratches.

Accessories

05P45.51 A2 Blade, right

05P45.52 A2 Blade, left

05P45.55 O1 Blade, right

05P45.56 O1 Blade, left

05P45.71 PM-V11®Blade, right

05P45.72 PM-V11®Blade, left

05P45.60 Optional Long Fence Rods, pr.

05N35.11 Replacement Scoring Blade

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali VERITAS Utensili

VERITAS

VERITAS 05P30.01 Manuale utente

VERITAS

VERITAS 05P22.15 Manuale utente

VERITAS

VERITAS 325650 Manuale utente

VERITAS

VERITAS 05P38.01 Manuale utente

VERITAS

VERITAS Tail Vise Manuale di istruzioni

VERITAS

VERITAS Mk.II Honing Manuale utente

VERITAS

VERITAS Small Drill-Press Table and Fence Manuale utente

VERITAS

VERITAS 05P38.07 Manuale utente

VERITAS

VERITAS 05G34.01 Manuale di istruzioni

VERITAS

VERITAS 05P33.70 Manuale utente

VERITAS

VERITAS Small Plow Plane Manuale utente

VERITAS

VERITAS 05G30.01 Manuale utente

VERITAS

VERITAS Prairie Dog 05G10.22 Manuale utente

VERITAS

VERITAS 05P75.01 Manuale utente

VERITAS

VERITAS Carver's Bench Manuale utente

VERITAS

VERITAS 70G08.01 Manuale utente

VERITAS

VERITAS 05P59.01 Manuale utente

VERITAS

VERITAS Mk.II Manuale utente

VERITAS

VERITAS Custom Smooth Plane No.4 Manuale utente

VERITAS

VERITAS 717636 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare