Yost Vises 10WW-RA Manuale utente

Warning:

Misuse of vises can cause serious injury to eyes, hands and or other body parts. Vises must be

set up and used properly. Before setup and use, read, understand and follow all instructions

outlined.

ALWAYS make sure bench

tops are properly secured.

ALWAYS use proper

mounting hardware in all

mounting holes to hold vise

securely.

ALWAYS inspect mounting

hardware to ensure vise is

securely fastened to work

bench.

ALWAYS inspect vise for

stress fatigue or damage to

the vise before using.

ALWAYS use vise of proper

size and capacity to hold work

object.

ALWAYS wear eye, face, and

ear protection when using a

vise.

ALWAYS wear dust mask or

respirator when working with

wood, metal, chemical dusts

or mists.

ALWAYS rest work piece

against front jaw and guide

rods.

ALWAYS wear restrictive hair

covering and anti slip

footwear while operating vise.

ALWAYS only hand tighten

vise.

ALWAYS maintain the vise –

grease main screw regularly.

Never use a hammer, extension

pipe, or cheater bar on spindle

handle of vise.

NEVER unscrew movable jaw

beyond maximum specified

opening of vise.

NEVER weld vise to any metal

object.

NEVER use a vise to press an

object into or out of another

object.

NEVER place pressurized

containers or combustible

materials in vise.

NEVER wear loose clothing or

jewelry while operating vise.

NEVER apply extreme heat or

prolong heat to the vise as it may

alter structural properties.

NEVER tighten work piece at the

edge (top or side) of the vise as

this may break vise casting

Mount Back Jaw Casting to Workbench

• Pre-drill holes for mounting screws using template provided. Be sure to drill

holes straight and deep enough to accommodate the full length of the screw.

Use recommended drill sizes only (see template provided).

• It is CRITICAL that the back jaw casting is mounted firmly and accurately to the

workbench surface. NO GAPS between the casting and the workbench should

be present. Use shims as needed. Refer to figure #1 below.

• DO NOT attach the vise to the end grain side of the workbench. By attaching the

vise to the side grain side of the workbench the mounting screw will have a much

stronger hold.

• When attaching the back jaw casting to the workbench, take care to ensure there

is full contact of the casting to the workbench surface before tightening the

mounting screws.

• The vertical portion of the back jaw against the front edge of the workbench and

the horizontal portion of the casting on the underside of the bench must have full

contact with the workbench. Use shims to eliminate any gaps that may be

present.

• Any gaps between the casting and the workbench surface will cause flexing of

the casting when tightened down, which could result in failure of the casting.

Figure 1.

• MOUNTING HARDWARE: Use the #14 x 2-1/2” Counter-Sink Wood Screws (2)

for the front edge mounting holes and the 5/16” x 2-1/2” Lag Screws (2) and the

5/16” Flat Washers (2) for underneath the workbench

Figure 1: Mount Back Jaw Casting to Work Bench

100 lbs.

Max

Yost 10WW Mounting Template

.300 .300

18” (Closed)

10”

13”

4.18”

.38” Diameter

38 Lbs

22.25”

10”

5.75”

4.00”

8.38”

4.125”

10.88”

Questo manuale è adatto per i seguenti modelli

Altri manuali Yost Vises Utensili

Yost Vises

Yost Vises 904-AS Manuale utente

Yost Vises

Yost Vises 880-DI Manuale utente

Yost Vises

Yost Vises 7WW-DI Manuale utente

Yost Vises

Yost Vises LV-4 Manuale utente

Yost Vises

Yost Vises ADI-5 Manuale utente

Yost Vises

Yost Vises FSV-6 Manuale utente

Yost Vises

Yost Vises 908-AS Manuale utente

Yost Vises

Yost Vises 865-DI Manuale utente

Yost Vises

Yost Vises FSV-4 Manuale utente

Yost Vises

Yost Vises DPV-4 Manuale utente

Yost Vises

Yost Vises DPV-3 Manuale utente

Yost Vises

Yost Vises 906-HV Manuale utente

Yost Vises

Yost Vises 750-DI Manuale utente

Yost Vises

Yost Vises 2503 Manuale utente

Yost Vises

Yost Vises ADI-6 Manuale utente

Yost Vises

Yost Vises DPV-5 Manuale utente

Yost Vises

Yost Vises ADI-4 Manuale utente

Yost Vises

Yost Vises 905-HV Manuale utente

Yost Vises

Yost Vises FSV-7 Manuale utente

Yost Vises

Yost Vises ADI-8 Manuale utente

Yost Vises

Yost Vises FSV-5 Manuale utente

Yost Vises

Yost Vises 910-HV Manuale utente

Yost Vises

Yost Vises 904-HV Manuale utente

Yost Vises

Yost Vises RIA-4 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare