APS iBoard IB-R921 Manuale utente
Rev. 20211001
1
iBoard
®
iBoard® by APS PART#: IB-R921
READ INSTRUCTIONS CAREFULLY BEFORE START ING
INSTALLATION. REMOVE CONTENTS FROM BOX AND
VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS
RECOMMENDED.
*ROCKER PANEL MOUNT
*NO DRILLING REQUIRED
Item QTY Description Item QTY Description
1# 8Mounting Brackets 5# 16 M6X1-20mm Square Head Bolts
2# 16 M8X1.25-20mm Hex Bolts 6# 16 M6 Large Flat Washers
3# 24 M8 Flat Washers 7# 16 M6 Nylon Lock Nuts
4# 8M8 Nylon Lock Nuts
7 #
6 #
5 #
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X
3 # 4 #2 #
Rev. 20211001
2
iBoard
®
PassengerDriver Front
1#
1#
1#
1# 1#
1#
1# 1#
Rev. 20211001
3
iBoard
®
STEP 1
Start installation from the driver side of the vehicle. Identify the
mounting locations along the rocker panel, (Fig 1).
Select (1) Mounting Bracket, attach to the mounting locations
with (1) M8X1.25-20mm Hex Bolt and (1) M8 Flat Washer; at-
tach to the rocker panel with (1) M8X1.25-20mm Hex Bolt, (2)
M8 Flat Washers and (1) M8 Nylon Lock Nut, (Fig 1). Do not
fully tighten hardware at this time.
STEP 2
Move to the driver side other (3) mounting locations, repeat
Step 1 for (3) Mounting Brackets installation. Do not fully tight-
en hardware at this time.
Note: All (8) Mounting Brackets are universal.
(Fig 1) Driver Side Mounting Bracket Installed
(1) M8X1.25-20mm Hex Bolt
(1) M8 Flat Washer
Front
(1) M8X1.25-20mm Hex Bolts
(2) M8 Flat Washers
(1) M8 Nylon Lock Nut
Front
(Fig 2) Driver Side Mounting Bracket Installed
STEP 3
Select a Running Board. Slip (4) M6x1-20mm Square Head
Bolts into each bottom channel (Fig 3). Carefully position the
Running Board onto the (4) Mounting Brackets.
IMPORTANT: Do not slide the Running Board on the Brackets
or the bottom surface of the board will be damaged. Attach the
Running Board to each Mounting Bracket with (2) M6x1-20mm
Square Head Bolts, (2) M6 Large Flat Washers and (2) M6
Nylon Lock Nuts (Fig 4). Do not fully tighten at this time.
(Fig 3) Slip M6X1-20mm Square Head Bolts Into
The Bottom Channels
M6X1-20mm Square Head Bolts
Rev. 20211001
4
iBoard
®
STEP 4
Level and adjust the Running Board and fully tighten all hard-
ware.
Important: Please follow the recommended Tightening Tor-
ques shown in the table on page 1. Don’t over tighten, or
the nuts/bolts will be damaged.
STEP 5
Repeat Steps 1-4 for the other side Running Board installation.
The installation is completed.
Attention
Do periodic inspections to the installation to make sure
that all hardware is secure and tight.
In order to protect your bars/boards, please use only
mild soap/non-abrasive products for cleaning.
(Fig 4) Running Board Installed Onto Mounting Bracket
(2) M6X1-20mm Square Head Bolts
(2) M6 Large Flat Washers
(2) M6 Nylon Lock Nuts
Altri manuali APS Accessori per automobili
APS
APS IA20SJI8B Manuale utente
APS
APS GR18GEC00U Manuale utente
APS
APS IB04EDJ2B Manuale utente
APS
APS ELM205-V10 Manuale utente
APS
APS GR18HEC11A Manuale utente
APS
APS iArmor IA-S022 Manuale utente
APS
APS iBoard IB-R922 Manuale utente
APS
APS iArmor Manuale utente
APS
APS iBoard Manuale utente
APS
APS iArmor IA-S002H Manuale utente
APS
APS IA06SJA1B Manuale utente
APS
APS iBoard IB-R094 Manuale utente
APS
APS iBoard IB-R911 Manuale utente
APS
APS IB03DJJ7A Manuale utente
APS
APS iArmor Manuale utente
APS
APS iBoard IB-R054 Manuale utente
APS
APS iBoard IB-019&020A-B Manuale utente
APS
APS iArmor Manuale utente
APS
APS IB14DBB5B Manuale utente
APS
APS IA06SAG5B Manuale utente
