Atdec VFS-DV Manuale utente
VFS-DV Page 1 of 4
Installation Guide
VFS-DV
COMPONENT CHECKLIST
E
VESA
Plate
(x2)
D
VFS Display
Head
(x2)
B
Upright
Pole
(x1)
A
Base
(x1)
L
(Optional)
Security
Screw
(x2)
M
Cable Ball
(x4)
F
3/5mm
Allen Key
(x1 each)
G
M8x50mm
Screw (x1)
I
Mounting
Screw
M4x16mm
(x8)
J
Mounting
Screw
M4x12mm
(x8)
K
Mounting
Screw
M4x10mm
(x8)
N
Cable Clip
(x3)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Each VFS Display Head supports a maximum weight as per above weight range specification.
! Each 750mm (29.5”) Upright Pole supports a maximum of two VFS Display Heads.
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! The manufacturer accepts no responsibility for incorrect installation.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset
VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the
stated range. Please contact Atdec if you would like further information.
Freestanding Dual Vertical
REQUIRED TOOLS
• Phillips Head Screwdriver
WEIGHT RANGE
Per Monitor
Flat Monitor
0 - 12kg (0 - 26.5lb)
Curved Monitor
0 - 9kg (0 - 20lb)
NOTE
120mm (4.75”) max
overall monitor depth
VFS-DV Page 2 of 4
2. Attach VFS Display Heads to the Pole (Ensure the cable slot faces towards the rear)
2.1 Slide the VFS Display Head
onto the Pole.
2.2 If the VFS Display Head requires further
tightening use the supplied 5mm Allen key.
2.3 Close the lever to lock the VFS Display
Head in place.
Slot
Groove
Insert
TIGHTEN
LOOSEN CLOSE
3. Attach the VESA Plate to your monitor (Repeat steps 3 to 6 for each monitor)
NOTE: Be sure to select a screw
length that suits the monitor.
3.1 Check VESA mounting compatibility. 3.2 Screw VESA Plate to back of
monitor using provided screws.
100mm
75mm
100mm 75mm
Top of
monitor
Too short Too long
OK
1. Attach Upright Pole to Base
1.1 Attach the Upright Pole to the
Base as shown below. Ensure the
Cable Slot faces towards the rear. OPTIONAL
BOLT THROUGH &
GROMMET MOUNT
Mount can also be bolted
to work surface or via
grommet hole with the
Atdec Grommet Clamp
(AC-GC), sold separately.
Cable Slot
USER
BACK
TIGHTEN
FIRMLY
Upright Pole
M8x50mm Screw
5mm Allen Key
VFS-DV Page 3 of 4
5. Adjust the Height of the VFS Display Head
5.1 While supporting the weight of the monitor, open
the lever to loosen the VFS Display Head.
5.2 Slide the VFS Display Head to desired position.
5.3 If necessary, adjust the tension between the Display
Head and the Pole using the 5mm Allen Key supplied.
5.4 Close the lever to lock the VFS Display Head in place.
OPEN
LOOSEN
TIGHTEN
CLOSE
HOOK
Back of Display
PUSH
Release
Button
Phillips-head
Screwdriver
Security
Screw
TIGHTEN
4. Attach your Display to the VFS Display Head
4.1 Hook the top of the VESA plate
onto the Display Head Mount.
4.2 Press and hold the Release
Buttons. Gently push bottom of
VESA Plate into Display Head Mount.
Release Buttons to lock in place.
4.3 (Optional) Insert the Security
Screw, and tighten using a Phillips-head
Screwdriver.
VFS-DV Page 4 of 4
Cable
Balls
(x2)
Cable
Clips
(x2)
OR
7. Cable Management
Connect cables to your Displays,
routing them down to the rear of
the poles.
Push the cables into the slots, using
either the Cable Balls or Cable Clips
to secure them to the pole as shown.
Note: Ensure enough slack is left in
cables to allow for movement. When
the slot in each pole cannot be used,
use the supplied Cable Clips to
secure the cables.
6. Adjust the ball joint tension
6.1 If the monitors are not holding
position or are stiff to move, adjust
the tension plate by tightening or
loosening the three screws.
Note: Adjust 3
screws evenly in
small increments
Note: Support the monitor
while making adjustments.
+-
+-
3mm
Allen Key
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20201204
Indice
Altri manuali Atdec Rack e supporto
Atdec
Atdec AWMS-2-LTH75-H Manuale utente
Atdec
Atdec AD-TVAC-CM Manuale utente
Atdec
Atdec AWMS-2-4640-C Manuale utente
Atdec
Atdec AWM-WS Manuale utente
Atdec
Atdec AF-AT-NBC Manuale utente
Atdec
Atdec TELEHOOK 12/30 Multi Manuale utente
Atdec
Atdec AWM-W6 Manuale utente
Atdec
Atdec Levitate L-PB Manuale utente
Atdec
Atdec AWMS-DW Manuale utente
Atdec
Atdec AWM-A46-B Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec ADBS-3x1-30T3C Manuale utente
Atdec
Atdec AWM-A13 Manuale utente
Atdec
Atdec Telehook Manuale utente
Atdec
Atdec ADBS-3x1-30TW Manuale utente
Atdec
Atdec AWMS-2-BT75-G Manuale utente
Atdec
Atdec AWM-HS Manuale utente
Atdec
Atdec VFS-Q Manuale utente
Atdec
Atdec AWM-BT Manuale utente
Atdec
Atdec AF-AN Manuale utente
