BGS technic 8482 Manuale utente

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 8482

Ball Joint Tool for BMW 3 Series

A professional quality tool designed for easy removal and insertion of press fit control arm ball joints

Suitable for use on BMW 3 series (E36) models

1. Press Frame Assembly

2. Removal Shell

3. Installation Shell

4. Drive Screw with Thrust Bearing

5. Spindle Support

6. Support

7. Removal Bush

8. Installation Bush

WARNING

Before starting work under a car always ensure that it is adequately supported by axle stands or

ramps.

Chock wheels and ensure that the hand brake is firmly applied.

Always work in a well ventilated area.

Always use approved eye protection especially when working under vehicles.

Ensure that tools are correctly mounted.

Always use workshop manual for detailed instructions.

Do not over tighten or use undue force as this can cause damage to both tool and component.

Always lubricate screw thread.

Do not use an impact wrench with this tool

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Extraction Insertion

A = Bush

1. Securely support the vehicle and follow workshop manual instructions to access the ball joint.

Mark the position of the ball joint to ensure the new ball joint is correctly installed.

2. Ensure that the screw threads (4) are clean, in good condition and freely lubricated each time

before use.

3. To remove the old ball joint assemble the tool as shown, using the bright plated shells (2) &

(7). Note ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to

slowly turn the drive screw (4) to extract the ball joint from the control arm.

4. Clean the lower face & bore of the control arm using a wire brush to remove any rust. Do not

apply any grease to the bore or the ball joint taper.

5. To install the new ball joint assemble the tool as shown, using the shells (8) & (3). Note:

ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to slowly turn

the drive screw (4) to insert the ball joint into the control arm. Always lubricate the screw

threads before using the tool.

Indice

Altri manuali BGS technic Utensili

BGS technic

BGS technic 9992 Manuale utente

BGS technic

BGS technic 9465 Manuale utente

BGS technic

BGS technic 2850 Manuale utente

BGS technic

BGS technic 70946 Manuale utente

BGS technic

BGS technic BGS 9992 Manuale utente

BGS technic

BGS technic 8737 Manuale utente

BGS technic

BGS technic 9689 Manuale utente

BGS technic

BGS technic 71040 Manuale utente

BGS technic

BGS technic 9605 Manuale utente

BGS technic

BGS technic 149 Manuale utente

BGS technic

BGS technic 8408 Manuale utente

BGS technic

BGS technic 8964 Manuale utente

BGS technic

BGS technic 62665 Manuale utente

BGS technic

BGS technic 8835 Manuale utente

BGS technic

BGS technic 3391 Manuale utente

BGS technic

BGS technic 875 Manuale utente

BGS technic

BGS technic 8687 Manuale utente

BGS technic

BGS technic 9637 Manuale utente

BGS technic

BGS technic BGS 1924 Manuale utente

BGS technic

BGS technic 3515 Manuale utente

BGS technic

BGS technic 3058 Manuale utente

BGS technic

BGS technic BGS 8156 Manuale utente

BGS technic

BGS technic 6650 Manuale utente

BGS technic

BGS technic 9538 Manuale utente

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare

Goobay

Goobay 97790 Manuale utente