Billion BiPAC 7202 Manuale utente
BiPAC 7202 / 7202GR2
(802.11g) ADSL2+ Router
Quick Start Gui e
Billion BiPAC 7202 / 7202GR2 ADSL2+Router
1
Package Contents
BiPAC 7202 series ADSL2+ Router
CD-ROM containing the on-line manual
R -11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
Do not use the router in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router are too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this product and all accessories outdoors.
Warning
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
Attention
For more detailed instructions on configuring and using the
(802.11g) ADSL2+ Router, please refer to the on-line
anual.
Quick Start Gui e
2
The Front LEDs
BiPAC 7202
BiPAC 7202GR2
LED Meaning
1 PPP :
Lit steady when there is a PPPoA / PPPoE connection.
2 ADSL:
Lit when successfully connected to an ADSL DSLAM (“linesync”).
3 LAN Port:
Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4
WLAN :
(7202GR2
only)
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
5 SYS :
Lit when the system is ready.
6 PWR :
Lit when power is ON.
Billion BiPAC 7202 / 7202GR2 ADSL2+Router
3
The Rear Ports
BiPAC 7202
BiPAC 7202GR2
Port Meaning
1 Power Switch
Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3
RESET
(
Emergency/Fai
lure Recovery)
1. After the device is powered on, press it to perform Failure
recover for a dead routers:
Simply hold the Emergency/Failure Recovery Button” when power
on the routers and download the Application if necessary.
2. perform the Emergency Recover for the missing Password
case:(Using LEDs indications)
Simply hold the Emergency/Failure Recovery Button, when router
can be accessed from GUI, until the LEDs all turn Off, turn On and
then Turn Off. Then, router will perform configuration factory reset
and router reboot
4
LAN
(RJ-45
connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC or an office/home network of
10Mbps or 100Mbps.
5
ADSL
(LINE)
Connect the supplied R -11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
2
5
4
2
3
4
5
1
3
Quick Start Gui e
4
Connecting BiPAC 7202
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR an SYS LEDs are lit steadily and that the relevant LAN LED is lit.
Billion BiPAC 7202 / 7202GR2 ADSL2+Router
5
Connecting BiPAC 7202GR2
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS, an WLAN LEDs are lit steadily and that the relevant LAN LED is
lit.
Quick Start Gui e
6
Configuring PC in Win ows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP a ress
automatically and the Obtain DNS server
a ress automatically radio buttons.
6. Click OK to finish the configuration.
Billion BiPAC 7202 / 7202GR2 ADSL2+Router
7
Configuring PC in Win ows 2000
1.
Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network an Dial-up
Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP a ress
automatically and the Obtain DNS server
a ress automatically radio buttons.
6. Click OK to finish the configuration.
Configuring PC in Win ows 98/Me
Quick Start Gui e
8
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP a ress
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
Configuring PC in Win ows NT4.0
Altri manuali per BiPAC 7202
5
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Billion Router di rete
Billion
Billion BiPAC 7402VGO Manuale utente
Billion
Billion M500 Manuale utente
Billion
Billion BiPAC 7300 Manuale utente
Billion
Billion BiPAC 5200W-T R2 Manuale utente
Billion
Billion BiPAC 7402G Manuale utente
Billion
Billion BiPAC 7402NX Manuale utente
Billion
Billion BiPAC 7100SG Manuale utente
Billion
Billion BiPAC 7202GR2 Manuale utente
Billion
Billion BiPAC 7402GL R4 Manuale utente
Billion
Billion BiPAC 8500/8520 Manuale utente
Billion
Billion BiPAC 7800(N) Manuale utente
Billion
Billion BiPAC 6200NXL Manuale del proprietario
Billion
Billion BiPAC 7404VNOX Manuale utente
Billion
Billion BiPAC 7404V series Manuale utente
Billion
Billion BiPAC 8700AX-1600 Manuale utente
Billion
Billion BiPAC 5210S Manuale utente
Billion
Billion BiPAC 5200G Series Manuale utente
Billion
Billion 800VGT Manuale utente
Billion
Billion BiPAC 7402G Manuale utente
Billion
Billion BiPAC 6404VP Manuale utente
