B+K precision 601B Manuale utente

Model: 601B

SLA Battery Capacity

Analyzer

USER MANUAL

Safety Summary

The following safety precautions apply to both operating and maintenance personnel and must be followed

during all phases of operation, service, and repair of this instrument.

Before applying power to this instrument:

Read and understand the safety and operational information in this manual.

Apply all the listed safety precautions.

Verify that the voltage selector at the line power cord input is set to the correct line voltage. Operating

the instrument at an incorrect line voltage will void the warranty.

Make all connections to the instrument before applying power.

Do not operate the instrument in ways not specified by this manual or by B&K Precision.

Failure to comply with these precautions or with warnings elsewhere in this manual violates the safety

standards of design, manufacture, and intended use of the instrument. B&K Precision assumes no liability for a

customer’s failure to comply with these requirements.

Category rating

The IEC 61010 standard defines safety category ratings that specify the amount of electrical energy available

and the voltage impulses that may occur on electrical conductors associated with these category ratings. The

category rating is a Roman numeral of I, II, III, or IV. This rating is also accompanied by a maximum voltage of

the circuit to be tested, which defines the voltage impulses expected and required insulation clearances. These

categories are:

Category I (CAT I): Measurement instruments whose measurement inputs are not intended to be connected to

the mains supply. The voltages in the environment are typically derived from a limited-energy transformer or a

battery.

Category II (CAT II): Measurement instruments whose measurement inputs are meant to be connected to the

mains supply at a standard wall outlet or similar sources. Example measurement environments are portable

tools and household appliances.

Category III (CAT III): Measurement instruments whose measurement inputs are meant to be connected to the

mains installation of a building. Examples are measurements inside a building's circuit breaker panel or the

wiring of permanently-installed motors.

Category IV (CAT IV): Measurement instruments whose measurement inputs are meant to be connected to the

primary power entering a building or other outdoor wiring.

Do not use this instrument in an electrical environment with a higher category rating than what is specified in

this manual for this instrument.

You must ensure that each accessory you use with this instrument has a category rating equal to or higher than

the instrument's category rating to maintain the instrument's category rating. Failure to do so will lower the

category rating of the measuring system.

Do not operate in an explosive or flammable atmosphere

Do not operate the instrument in the presence of flammable gases or vapors, fumes, or finely-divided

particulates.

The instrument is designed to be used in office-type indoor environments. Do not operate the instrument

In the presence of noxious, corrosive, or flammable fumes, gases, vapors, chemicals, or finely-divided

particulates.

In relative humidity conditions outside the instrument's specifications.

In environments where there is a danger of any liquid being spilled on the instrument or where any

liquid can condense on the instrument.

In air temperatures exceeding the specified operating temperatures.

In atmospheric pressures outside the specified altitude limits or where the surrounding gas is not air.

In environments with restricted cooling air flow, even if the air temperatures are within specifications.

In direct sunlight.

This instrument is intended to be used in an indoor pollution degree 2 environment. The operating

temperature range is 0 °C to 40 °C and the operating humidity range is ≤95%relative humidity with no

condensation allowed.

Measurements made by this instrument may be outside specifications if the instrument is used in non-office-

type environments. Such environments may include rapid temperature or humidity changes, sunlight, vibration

and/or mechanical shocks, acoustic noise, electrical noise, strong electric fields, or strong magnetic fields.

Do not operate instrument if damaged

If the instrument is damaged, appears to be damaged, or if any liquid, chemical, or other

material gets on or inside the instrument, remove the instrument's power cord, remove the instrument from

service, label it as not to be operated, and return the instrument to B&K Precision for repair. Notify B&K

Precision of the nature of any contamination of the instrument.

Clean the instrument only as instructed

Do not clean the instrument, its switches, or its terminals with contact cleaners, abrasives, lubricants, solvents,

acids/bases, or other such chemicals. Clean the instrument only with a clean dry lint-free cloth or as instructed

in this manual.

Not for critical applications

This instrument is not authorized for use in contact with the human body or for use as a component in a life-

support device or system.

Do not touch live circuits

Instrument covers must not be removed by operating personnel. Component replacement and internal

adjustments must be made by qualified service-trained maintenance personnel who are aware of the hazards

involved when the instrument's covers and shields are removed. Under certain conditions, even with the power

cord removed, dangerous voltages may exist when the covers are removed. To avoid injuries, always

disconnect the power cord from the instrument, disconnect all other connections (for example, test leads,

computer interface cables, etc.), discharge all circuits, and verify there are no hazardous voltages present on

any conductors by measurements with a properly-operating voltage-sensing device before touching any

internal parts. Verify the voltage-sensing device is working properly before and after making the measurements

by testing with known-operating voltage sources and test for both DC and AC voltages. Do not attempt any

service or adjustment unless another person capable of rendering first aid and resuscitation is present.

Do not insert any object into an instrument's ventilation openings or other openings.

Servicing

Do not substitute parts that are not approved by B&K Precision or modify this instrument. Return the

instrument to B&K Precision for service and repair to ensure that safety and performance features are

maintained.

For continued safe use of the instrument

Do not place heavy objects on the instrument.

Do not obstruct cooling air flow to the instrument.

Do not place a hot soldering iron on the instrument.

Table of Contents

Section 1 General Description .................................................................................................................................. 9

1.1 INTRODUCTION .............................................................................................................................................. 9

1.2 APPLICATIONS................................................................................................................................................. 9

1.3 SPECIFICATIONS.............................................................................................................................................. 9

Section 2 Operation................................................................................................................................................ 10

2.1 Front Panel Controls..................................................................................................................................... 10

2.2 Operating Procedure .................................................................................................................................... 11

Service Information ............................................................................................................................................... 14

Limited One-Year Warranty .................................................................................................................................. 15

Section 1 General Description

1.1 INTRODUCTION

B&K Precision Battery Capacity Analyzer Model 601B measures the terminal voltage, internal resistance, and percent of charged capacity

left in a battery.

The model 601B supports 6V & 12V storage type lead acid batteries with wide range of Ah capacity. No external power (Mains or DC) is

required. The unit works on the BUT (Battery Under Test) power.

1.2 APPLICATIONS

As the information age develops it is likely that the demand for UPS units will increase for use in hospitals, offices, labs etc. It is expected that

the importance of battery maintenance will increase along with increasing demand for UPS.

The 601B can be applicable for Automobile Service Stations, UPS Manufacturing, Maintenance and Field Servicing, QC Department, Battery

Systems in Railways, Telecommunications, Ships / Submarine.

1.3 SPECIFICATIONS

NOTE: Specifications and information are subject to change without notice.

Please visit www.bkprecision.com for the most current product information.

Voltage Ranges: 6V, 12V automatically selected

Display: i) Capacity 0% to 100%.

ii) No load Voltage & loaded Voltage.

iii) Internal Resistance.

Min. Input Voltage: 4.8V

Max. Input Voltage: 20V

Measurable Ah Selection: Programmable 5-100Ah in steps of 1Ah.

No Load Voltage Accuracy: ±0.2% ±1 counts.

Voltage Resolution: 10mV.

Dimensions (WxHxD): 2.91 x 10.44 x 2.28”

(74 x 26 5 . 1 x 5 8 mm )

Weight: 2.65lb (1.2 kg)

Section 2 Operation

2.1 Front Panel Controls

1. Power / Select: Powers on unit after connecting to BUT. Also used to select Ah seting.

After activation user can select the Ah values as per BUT rating using this key.

2. Up: This key is used to increase the Ah values.

3. Down: With this key, the user can decrease the Ah values.

4. Test: On pressing this key the measurement will begin.

5. Repeat Test: This key is used to repeat previously performed test.

6. Reverse Polarity LED: This LED glows when the battery is reverse connected.

7. LCD : This is 16x2 line alphanumeric display. It displays various messages & results of tests

as per Ah value selected.

8. -ve Cable: Negative connecting cable with strain relief.

9. +ve Cable: Positive connecting cable with strain relief.

Altri manuali per 601B

Indice

Altri manuali B+K precision Strumento di misura

B+K precision

B+K precision 830C Manuale utente

B+K precision

B+K precision 177/V-95 Manuale utente

B+K precision

B+K precision 4045B Manuale utente

B+K precision

B+K precision 5335C Manuale utente

B+K precision

B+K precision 5335B Manuale utente

B+K precision

B+K precision 467 Manuale utente

B+K precision

B+K precision 5335B Manuale utente

B+K precision

B+K precision 467 Manuale utente

B+K precision

B+K precision 732A Manuale utente

B+K precision

B+K precision 2530B Manuale utente

B+K precision

B+K precision DAS30 Manuale utente

B+K precision

B+K precision Sefram DAS240 Manuale

B+K precision

B+K precision 310 Manuale utente

B+K precision

B+K precision 4063 Manuale utente

B+K precision

B+K precision 2652A Manuale utente

B+K precision

B+K precision 880 Manuale utente

B+K precision

B+K precision 302 Manuale utente

B+K precision

B+K precision 1050 Manuale utente

B+K precision

B+K precision 885 Manuale utente

B+K precision

B+K precision 2650 Manuale utente

B+K precision

B+K precision 830C Manuale utente

B+K precision

B+K precision 603B Manuale utente

B+K precision

B+K precision 5335B Manuale utente

B+K precision

B+K precision 600B Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente