Clarke CAT218 Manuale di installazione e funzionamento

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC 04-22

6PC AIR SCRAPER TOOL SET

MODEL NO: CAT218

PART NO: 3110472

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Scraper Tool Set.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATIONS

Please note that the details and specifications contained herein are correct

at the time of going to print. However CLARKE International reserve the right to

change specifications at any time without prior notice. Always consult the

machine’s data plate.

Model Number CAT218

Dimensions (L x W x H) 210 x 50 x 35 mm

Weight 1 kg

Air Inlet Size 1/4“BSP (female)

Operating Pressure 90 psi (6.2 bar)

Air Consumption 1.25 cfm (average)

Blows per minute 4500 bpm

Stroke length 1-9/16”

Sound Pressure Level (LpA dB) 83 dB(A)

Guaranteed Sound Power 94 dB(A)

Vibration Levels 9.5 m/s2

Uncertainty Factor 1.5

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - DO NOT wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - DO NOT let children handle the tool.

4. DO NOT operate the tool where there are flammable liquids or gases.

PERSONAL SAFETY

1. Stay alert and use common sense - do not operate the air tool when you

are tired or under the influence of alcohol, drugs or medication.

2. ALWAYS wear eye protection when using the tool - This must provide

protection from flying particles from the front and the side.

3. ALWAYS wear ear protection when using the air tool.

4. ALWAYS wear a dust mask when operating this type of tool.

5. DO NOT overreach - Keep proper footing and balance at all times.

6. Remove any wrench before turning the power tool on. A wrench left

attached to a moving part of the power tool may result in personal injury.

USE OF AIR POWERED TOOLS

1. NEVER use oxygen, CO2, combustible gases or any type of bottled gas as a

source of power for the tool.

2. DO NOT connect the air supply hose with your finger on the trigger.

3. DO NOT exceed the maximum pressure for the tool of 90 psi / 6.2 bar.

4. Check hoses for leaks or worn condition before use, and ensure that all

connections are secure.

5. DO NOT use the tool for any other purpose than that described in this

manual.

6. ALWAYS keep the air supply hose away from heat, oil and sharp edges.

7. DO NOT fit the tool to any stand or clamping device that may damage it.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

8. DO NOT carry out any alterations or modifications to the tool.

9. ALWAYS disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

• The tool will be left unattended.

• Moving to another work area.

• Passing the tool to another person.

10. NEVER use the tool if it is defective or operating abnormally.

11. The tool should be serviced at regular intervals by qualified service

personnel.

12. Avoid damaging the tool by applying excessive force of any kind.

13. ALWAYS maintain the tool with care. Keep it clean for the best and safest

performance.

14. Quick change couplings should not be located at the tool. They add

weight and could fail due to vibration.

15. DO NOT force or misuse the tool. It will do a better and safer job at the rate

for which it was designed.

16. This tool vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

AIR CHISEL SPECIFIC HAZARDS

1. Only use accessories designed for use with this tool.

2. NEVER use any of the blades supplied as a hand struck tool.

3. NEVER use blunt blades which require excessive pressure and can break

from fatigue. ALWAYS use sharp tools.

4. NEVER mis-use the tool by prizing which can result in a broken tool.

5. Ensure there are no hidden electrical cables, gas pipes etc, which could

cause a hazard if damaged by action of the blades.

USE OF THE SCRAPING TOOL

1. Ensure that the workpiece is kept at waist height where possible. NEVER use

the tool between the legs whilst sitting on the floor.

2. ALWAYS allow the tool to run up to full operating speed before applying it

to the job.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3. Use clamps, or vices to hold a loose workpiece. Failure to secure the

workpiece could result in personal injury.

4. Inspect the blades before use. DO NOT use if damaged.

5. ALWAYS wear a face mask when using the tool as protection from

airbourne particles. Avoid disturbing existing dust and minimise the

scattering of dust in the workplace environment. Take steps to control the

dust at the point of emission.

TRANSPORTATION AND STORAGE

1. NEVER carry the tool by the air supply hose.

2. NEVER carry the tool with your finger on the trigger.

3. When not in use the tool should be disconnected from the air supply and

stored in a dry place out of the reach of children.

4. Avoid storing the tool in environments where the temperature is below 0oC.

COMPRESSED AIR REQUIREMENTS

Use only clean, dry, regulated compressed air as a power source.

Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

A build-up of moisture or oil in the air compressor will accelerate wear and

corrosion in the tool. ensure any moisture is drained from the compressor daily

and the inlet filter is kept clean.

If an unusually long air hose is required, (over 8 metre by up to 15 psi to

maintain air pressure at the tools), the line pressure or the hose inside diameter

may need to be increased.

For optimum performance it is recommended that a 3/8” I/D airline hose is

used.

A typical air line layout is shown below. If an automatic in-line filter/regulator is

used, it will keep the tool in good condition, but should be regularly checked

and topped up with oil. SAE 10 oil should be used, and the lubricator adjusted

to approx 2 drops per minute.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND COMPRESSED AIR SUPPLIES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

The air hose must be rated at least 150% of the maximum operating pressure of

the tool.

Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 90 psi at the tool

when running. Higher pressures and unclean air will shorten the life of the tool

due to faster wear and is a possible safety hazard.

Check air hose for wear of damage before use.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Blade Locking screws 6 Allen (hex) Key

2Trigger 71¾” Wide Curved Blade

3 Speed Regulator 8 1¾” Offset Blade

4 Air Inlet Port (with travel plug) 9 1” Flat Blade (one shown fitted)

5 Inlet hose adaptor 10 1” 45 degree Angled Blade

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

NOTE: Ensure the compressor is turned off and remove the travel plug

from the inlet connection of the air tool.

1. If required, connect an in-line mini

oiler to the tool.

• A mini oiler helps to prolong the

life of the air tool.

2. Connect a suitable hose to the air

inlet as shown by screwing in the

male connector as shown.

3. Connect the other end of the hose

to the compressor.

4. Run the compressor at low pressure and check for leaks.

5. If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the air inlet or via the hose at the

nearest connection to the air supply.

Your air tool is now ready for use. You can fit a whip hose with a quick fit

coupling if required (available from your Clarke dealer).

FITTING THE BLADES

CAUTION: THE BLADES ARE SHARP AND MAY CUT YOU IF BADLY HANDLED.

TAKE CARE DURING BLADE INSTALLATION AND REMOVAL.

1. Disconnect the air scraper

from the air supply and

squeeze the trigger lever (C) to

release any residual air.

2. Choose the blade that is

appropriate for the task.

3. Loosen both cap head screws (A)

with a hex key. Remove the

screws by hand.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND COMPRESSED AIR SUPPLIES.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

4. Remove the current blade by sliding it out of the blade holder (B). Be

careful of the sharp edge.

5. Hold the blade only by the flat surfaces. Insert the selected blade into the

blade holder's slot and align the blade bolt holes with the screw holes.

Make sure the bevel is facing upward (same facing as the screws).

6. Insert a screw into a screw hole and hand-tighten. Repeat with the second

screw. You may need to shift the blade if the bolt holes are not aligned to

allow the screw to enter the bottom half of the blade holder. Tighten with

the hex key. DO NOT overtighten.

7. Reconnect the air hose and start the compressor.

8. Test the air scraper without load to ensure the blade is secure. Point the

blade at an unoccupied spot in case the blade is ejected.

OPERATION

1. Set up the compressor and re-set

the air pressure to the scraper.

2. Squeeze the trigger to start the

tool and the blade will vibrate.

3. Increase or decrease the blows/

minute by adjusting the airflow

regulator.

4. Place the blade firmly at an angle

between the surface and the

material you want to remove.

Slowly push forward so the blade slides over the surface while separating

the unwanted material.

5. Release the trigger to stop the tool. Brush off all debris and resume scraping

until the task is complete.

SCRAPING TIPS

• DO NOT use excess pressure on the blade. Let the tool do the work.

• Allow the blade to reach working speed

• Avoid overloading the scraper If it becomes hot during use. Stop

work for a few minutes while it cools down.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DISCONNECTING THE AIR SUPPLY

1. DO NOT disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

2. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the tool.

CARE AND MAINTENANCE

DAILY

1. Before use, drain water from the air tank, air line and compressor.

2. Pour a few drops of CLARKE airline oil, into the air inlet. This should be

carried out regardless of whether or not an in-line mini oiler is used. If an in-

line mini oiler is not used, this procedure should be repeated after every

two to three hours of use.

CLEANING

1. Keep the body of the tool clean and free from debris.

2. Grit or gum deposits inside the tool

may also reduce its efficiency. This

condition can be corrected by

cleaning out the air strainer and

flushing out the tool with gum

solvent or oil, or failing this, the

motor may require dismantling.

This is better left to your CLARKE

dealer.

3. Periodically, check the air inlet

strainer for blockage and clean if

necessary.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Utensili

Clarke

Clarke X-PRO CAT208 Manuale di installazione e funzionamento

Clarke

Clarke CAT33B Manuale di installazione e funzionamento

Clarke

Clarke CHT172 Manuale utente

Clarke

Clarke CHT637 Manuale di installazione e funzionamento

Clarke

Clarke GWH8 Manuale di istruzioni

Clarke

Clarke Air CAT62 Manuale di installazione e funzionamento

Clarke

Clarke SBR610 Manuale di istruzioni

Clarke

Clarke CHT878 Manuale utente

Clarke

Clarke CBS4 Manuale utente

Clarke

Clarke CAR8P Manuale utente

Clarke

Clarke CONTRACTOR CHJ110 Manuale di istruzioni

Clarke

Clarke CHT204 Manuale utente

Clarke

Clarke CHT 141 Manuale utente

Clarke

Clarke CAR15PC Manuale utente

Clarke

Clarke CAT33B Manuale di installazione e funzionamento

Clarke

Clarke CEA150 Manuale di installazione e funzionamento

Clarke

Clarke CMC36B Manuale utente

Clarke

Clarke METALWORKER CTR1 Manuale di istruzioni

Clarke

Clarke CHT 454 Manuale utente

Clarke

Clarke Strong-Arm CFB600 Manuale utente

Clarke

Clarke CAT29B Manuale di installazione e funzionamento

Clarke

Clarke CONTRACTOR CWJ700 Manuale di istruzioni

Clarke

Clarke CHT697 Guida all'installazione

Clarke

Clarke CDTJ12 Manuale di istruzioni

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare