Clarke CAT151 Manuale di installazione e funzionamento

OPERATING & MAINTENANCE

INSTRUCTIONS

GC0216

AIR/HYDRAULIC RIVETER

MODEL NO: CAT151

PART NO: 3120165

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Riveter. The CAT151 Air Riveter is

supplied with 4 nose pieces to accept 2.4 mm, 3.2 mm, 4.0 mm and 4.8 mm

rivets. The riveter has a hardened steel jaw assembly, a rivet stem safety cap,

and is suitable for both aluminium and steel rivets.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

OPERATING PRINCIPLE

The rivet is pushed through the hole in the workpiece and the rivet pin inserted

into the rivet gun nosepiece which will grip it tightly.

When the rivet gun is activated the throttle valve allows compressed air

through the tool. The pressure of the air forces the rivet pin into the jaws which

pull the pin up into the rivet. As the pin is taken up, the base of the rivet

expands and this joins the workpiece. The rivet gun pulls the pin until it breaks

off, thereby securing the rivet. The used pins are ejected into the safety cap

for disposal.

Pop rivets have limited strength so they are typically used for fastening light

sheet metals. Professionals sometimes refer to these rivets as blind rivets, as the

user cannot see the other side of the material being riveted.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

USE

1. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using air tools. Eye protectors must

provide protection from flying particles from the front and the side.

3. Do not overreach - keep proper footing and balance at all times.

4. Never use oxygen, CO2, combustible gasses, or any bottled gas, as a

source of power for an air tool. This product should only be used with a

suitably rated compressed air supply.

5. Do not connect the air hose with your finger on the trigger of the riveter.

6. Do not fit the air tool to any stand or clamping device that may damage it.

7. Do not exceed the maximum pressure for the tool of 7 bar.

8. Keep the air hose away from heat, oil and sharp edges.

9. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

10. Do not use the tool for any other purpose than described in this manual.

11. Do not carry out any alterations or modifications to the tool.

12. Always disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

• The tool will be left unattended.

• Never use the tool if it is defective or operating abnormally.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

13. This air tool should be serviced at regular intervals by qualified service

personnel.

14. Avoid damaging the air tool by applying excessive force of any kind.

15. Always maintain the air tool with care. Keep it clean for the best and safest

performance.

16. Do not force or misuse the air tool. It will do a better and safer job at the

rate for which it was designed.

17. Do not use the riveter if the safety cap is not in place.

18. Do not point the air tool at people or animals.

TRANSPORTATION

1. Never carry an air tool by the air hose.

2. Never carry an air tool with your finger on the trigger.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Nosepiece (2.4, 3.2, 4.0 & 4.8 dia) 7 1/4” BSP Air Inlet Connection

2 Outer Cylinder 8 Trigger

3 Hanging Ring 9 Spanner

4 Safety Cap 10 Spanner Gauge

5 Retaining ring for safety cap 11 Large and Small O-rings (see p11)

6 Air Cylinder

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked & topped up with oil. Clarke air-line oil should

be used, and the lubricator adjusted to approx 2 drops per minute.

• Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 7 bar at

the tool when running. Higher pressures and unclean air will shorten

the life of the tool due to faster wear and is a possible safety hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PREPARATION & ADJUSTMENT

FILLING/CHECKING THE OIL LEVEL

Before use, check that the rivet gun is topped up with hydraulic oil (not

supplied) after removing the cylinder cap and piston assembly to ensure that

it is properly lubricated.

1. Disconnect the riveter from the air

line.

2. Hold upside-down and remove the

air cylinder cap (fig 1) with the

spanner provided.

3. Remove the air/hydraulic piston

assembly (grip the exposed nut

and pull up) as in Fig 2.

4. Add hydraulic oil to the hydraulic

cylinder until the level is just below

the connection with the air

cylinder. See fig. 3.

• Hydraulic oil is avaialble from

your Clarke dealer: part No

3050830 (1 litre).

5. Lightly lubricate the inner wall of

the air cylinder.

6. Replace the air/hydraulic piston

assembly and press in as far as it will go.

7. Refit and tighten the air cylinder cap.

CHECKING/ADJUSTING THE STROKE

1. Check that the hydraulic oil level is

correct as above.

2. Remove the outer cylinder using

the spanner provided.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3. Check the jaw stroke by using the

spanner/gauge as in figs 5 and 6.

4. Set the distance to < 70 mm i.e. the

length of the spanner gauge as

shown.

5. If necessary, adjust the stroke as

follows:

• Hold the rear jaw case (fig 7)

with the larger spanner and

loosen the lock nut with the

spanner/gauge.

• Adjust the stroke by rotating the

jaw case assembly and

tightening the lock nut when

adjustment is complete.

6. Refit the outer cylinder.

CONNECTING THE AIRLINE

NOTE: Ensure the air compressor is turned off.

1. Remove the protective plug from

the air inlet port and connect a

suitable hose as shown.

2. Connect the other end of the hose

to the compressor.

3. Turn on the air supply and check

for air leaks. Rectify any leaks

found before proceeding.

• PTFE tape may be helpful for

sealing threaded connections.

4. If required, connect an in-line mini oiler into the air supply line to the tool.

• A mini oiler helps to prolong the life of the air tool.

• If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the inlet connector or via the

hose at the nearest connection to the air supply.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

5. Turn the compressor back on and set the regulator to 6.3 to 7 bar. Do not

exceed this pressure.

6. Your air riveter is now ready for use.

• You can fit a whip hose with a quick fit coupling if required

(available from your Clarke dealer).

OPERATION

1. Select the nosepiece to suit the rivet size and fit it to the head using the

spanner.

2. Insert the rivet stem fully through the nosepiece and into the jaws.

3. Press the rivet body through the pre-drilled hole in the workpiece and hold

the rivet flange flush against the workpiece. Always take care to drill the

holes with the same size drill bit as the rivets to be used.

4. Squeeze the trigger.

• The rivet will be compressed and the rivet stem will be ejected into

the safety cap from where they can be collected for disposal.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

2. Squeeze the trigger to discharge any compressed air from the riveter.

3. Once the pressure has been released, disconnect the air supply hose from

the air tool.

4. Store the tool safely in its box in a dry, secure environment.

WARNING: ALWAYS FIT THE SAFETY CAP TO THE REAR OF THE FRAME

BEFORE USE TO PREVENT INJURY FROM EJECTED RIVET STEMS. FIT WITH THE

SLOT FACING DOWNWARDS SO THAT THE STEMS FALL TO THE FLOOR.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

DAILY

1. Before use, drain water from the air-line and compressor.

2. Maintain the tool with care. Keep it oiled for optimum performance.

3. Lubricate the air tool daily with a high quality air tool oil either via an oiler in

the air supply system or by placing a few drops into the riveter air inlet

immediately before use. This should be carried out regardless of whether or

not an in-line mini oiler is used. If an in-line mini oiler is not used, this

procedure should be repeated after every two hours of constant use.

CLEANING

1. Keep the tool clean.

2. Deposits in the tool may also reduce efficiency. This can be corrected by

cleaning the air inlet and flushing out the tool with gum solvent oil, or failing

this, the tool should be disassembled, thoroughly cleaned, dried and

reassembled.

3. If the tool becomes inefficient and the air supply is of good quality, it may

be necessary to replace worn or damaged parts. You may prefer to take

the tool to your Clarke dealer if internal maintenance is required.

CHANGING JAWS

1. Disconnect the tool from the air

line.

2. Remove the outer cylinder (fig 9)

using the spanner provided.

3. Use both spanners to unscrew the

front jaw case (fig 10) from the rear

jaw case.

4. Remove the jaws and clean with

solvent and brush. If the teeth are

blunted, replace with new jaws.

Reverse the above procedure to reassemble.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Indice

Altri manuali Clarke Utensili

Clarke

Clarke CRT 40 Manuale utente

Clarke

Clarke CMFT220 Manuale di istruzioni

Clarke

Clarke CHT878 Manuale utente

Clarke

Clarke CAT216 Manuale di installazione e funzionamento

Clarke

Clarke CAT138 Manuale di installazione e funzionamento

Clarke

Clarke CHT172 Manuale utente

Clarke

Clarke CEA150 Manuale di installazione e funzionamento

Clarke

Clarke PC108 Istruzioni per il montaggio

Clarke

Clarke Metalworker CPTN1 Manuale di istruzioni

Clarke

Clarke CMC36B Manuale utente

Clarke

Clarke CAT33B Manuale di installazione e funzionamento

Clarke

Clarke CAT120 Manuale di istruzioni

Clarke

Clarke CHT691 Manuale utente

Clarke

Clarke KIT700 Manuale di istruzioni

Clarke

Clarke CAT29B Manuale di installazione e funzionamento

Clarke

Clarke CHT204 Manuale utente

Clarke

Clarke CBS4 Manuale utente

Clarke

Clarke GWH8 Manuale di istruzioni

Clarke

Clarke CHT718 Manuale utente

Clarke

Clarke CMFT250 Manuale di istruzioni

Clarke

Clarke CONTRACTOR CHJ110 Manuale di istruzioni

Clarke

Clarke SBR305 Manuale di istruzioni

Clarke

Clarke CHT 454 Manuale utente

Clarke

Clarke CAT114 Manuale di istruzioni

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare