Clarke CHT691 Manuale utente

OPERATING INSTRUCTIONS

GC01/12

TYROLEAN APPLICATOR GUN

Model: CHT691

Part No: 1801691

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE applicator gun.

Before using the product, be sure to read these instructions thoroughly. In

doing so you will ensure the safety of yourself and of others around you, and

you can look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase. This guarantee is invalid if the product is found to have been

abused or tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

CONTENTS

1 x Applicator Gun Assembly c/w comb assembly & spindle

1 x Operating Handle

1 x Reducer Plate

ASSEMBLY

The applicator gun should be

delivered with the revolving comb

and spindle assembled within the

unit, and the handle supplied loose.

1. Screw the handle into the right

hand end of the comb assembly

through the hole in the casing as

shown in Fig 1.

Note: If the handle were assembled at the left side, the handle would

unscrew during operation, therefore, the applicator gun is for

right-handed operation only.

Handle

Comb Assembly

Fig 1

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

OPERATION

1. Set the rod as required, by

tightening the wing nuts at each

side, as shown in Fig 2, taking

care the rod is set level.

2. Fill the body of the unit half full of

wall coating material. Do not

overfill.

• Wall coating materials are heavy

and easier to handle in small

quantities.

3. Rotate the handle in a clockwise

direction to spray the wall

coating material.

4. If required, attach the reducer

plate to the front of the unit for

coating small areas and re-

touching work. Insert the plate,

first, into the top of the front

opening, before sliding the lower

edge down into position as

shown in Fig 3.

CLEANING

1. To keep your applicator gun

clean and ready for use, wash

out thoroughly as soon as you

stop work.

• Residual material lodged in the

comb will greatly reduce its

future performance.

2. Unscrew the handle from one

end of the comb and the spindle

from the other end, then lift the comb assembly out of the casing as

shown in Fig 4, in order to clean it thoroughly with water.

REPLACEMENT PARTS

Replacement comb assemblies are available from your Clarke dealer as part

number: HTCHT69101.

ENVIRONMENTAL PROTECTION

Do not dispose of this product or damaged components with general

household waste. All tools, accessories and packaging should be sorted,

taken to a recycling centre and disposed of appropriately.

Comb just

touches rod

Wingnut

High

Low

Fig 2

Reducer plate

Fig 3

Spindle

Handle

Comb Assembly

Fig 4

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Clarke Utensili

Clarke

Clarke CHT878 Manuale utente

Clarke

Clarke CEA150 Manuale di installazione e funzionamento

Clarke

Clarke CBS4 Manuale utente

Clarke

Clarke SBR760 Manuale di istruzioni

Clarke

Clarke PC108 Istruzioni per il montaggio

Clarke

Clarke CAT138 Manuale di installazione e funzionamento

Clarke

Clarke CONTRACTOR CSJ100 Manuale di istruzioni

Clarke

Clarke CHT738 Manuale di istruzioni

Clarke

Clarke CMFT220 Manuale di istruzioni

Clarke

Clarke TPG30P Manuale utente

Clarke

Clarke CAT33B Manuale di installazione e funzionamento

Clarke

Clarke IT1500 Manuale di istruzioni

Clarke

Clarke CHT733 Manuale utente

Clarke

Clarke CAT125 Manuale di installazione e funzionamento

Clarke

Clarke CONTRACTOR CLJ120 Manuale di istruzioni

Clarke

Clarke CMC36B Manuale utente

Clarke

Clarke Air CAT62 Manuale di installazione e funzionamento

Clarke

Clarke SBR305 Manuale di istruzioni

Clarke

Clarke CHT 454 Manuale utente

Clarke

Clarke CRT 40 Manuale utente

Clarke

Clarke METALWORKER CMSSCS Manuale utente

Clarke

Clarke CSB20B Manuale utente

Clarke

Clarke CAT218 Manuale di installazione e funzionamento

Clarke

Clarke KIT1100 Manuale di istruzioni

Manuali Utensili popolari di altre marche

Martor

Martor SECUNORM 175 Manuale utente

ERKCO

ERKCO 1000 Manuale utente

jbc

jbc N4473 Manuale utente

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuale utente

Worx Professional

Worx Professional Sonicrafter WU676 Manuale utente

Gage Bilt

Gage Bilt GB713SH Manuale utente

Hilti

Hilti DX 9-ENP Manuale utente

norbar

norbar NORTRONIC 34399 Manuale utente

BGS technic

BGS technic 8578 Manuale utente

Makita

Makita DHR241 Manuale utente

Motor Guard

Motor Guard JMB-1250 Manuale utente

Power Adhesives

Power Adhesives 805-12 Manuale utente

Clemco

Clemco 24189 Manuale utente

VVG

VVG VNG 903 Series Manuale utente

Hilti

Hilti FX 3-A Manuale utente

Grizzly

Grizzly H6472 Manuale utente

axing

axing BWZ 5-02 Manuale utente

Dh-Robotics

Dh-Robotics RGI-100 Come usare