Dynojet Power commander V Manuale utente

22-001www.powercommander.com 2009 Yamaha R6S PCV - 1

PARTS LIST

1 Power Commander

1 USB Cable

1 CD-ROM

1 Installation Guide

2 Power Commander Decals

2 Dynojet Decals

2 Velcro

1 Alcohol swab

YOU CAN ALSO DOWNLOAD THE

POWER COMMANDER SOFTWARE AND

LATEST MAPS FROM OUR WEB SITE AT:

www.powercommander.com

2009 Yamaha R6S

I n s t a l l a t i o n I n s t r u c t i o n s

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

THE IGNITION MUST BE TURNED

OFF BEFORE INSTALLATION!

2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

22-001www.powercommander.com 2009 Yamaha R6S PCV - 2

EXPANSION PORTS 1 & 2

Optional Accessories such as

Color LCD unit or Auto tune kit.

POWER COMMANDER V

INPUT ACCESSORY GUIDE

Map - The PCV has the ability to hold 2 different

base maps. You can switch on the fly

between these two base maps when you hook

up a switch to the MAP inputs. You can use

any open/close type switch. The polarity of

the wires is not important. When using the

Autotune kit one position will hold a base map

and the other position will let you activate the

learning mode. When the switch is “CLOSED”

Autotune will be activated.

Shifter- These inputs are for use with the Dynojet

quickshifter. Insert the wires from the Dynojet

quickshifter into the SHIFTER inputs. The

polarity of the wires is not important.

Speed- If your application has a speed sensor then

you can tap into the signal side of the sensor

and run a wire into this input. This will allow

you to calculate gear position in the Control

Center Software. Once gear position is setup

you can alter your map based on gear position

and setup gear dependent kill times when

using a quickshifter.

Analog- This input is for a 0-5v signal such as

engine temp, boost, etc. Once this input

is established you can alter your fuel curve

based on this input in the control center

software.

Crank- Do NOT connect anything to this port unless

instructed to do so by Dynojet. It is used to

transfer crank trigger data from one module to

another.

ACCESSORY INPUTS

Wire connections:

To input wires into the PCV first remove the rubber

plug on the backside of the unit and loosen the

screw for the corresponding input. Using a 22-24

gauge wire strip about 10mm from its end. Push the

wire into the hole of the PCV until is stops and then

tighten the screw. Make sure to reinstall the rubber

plug.

NOTE: If you tin the wires with solder it will make

inserting them easier.

CRANK

ANALOG

SPEED

MAP

SHIFTER

USB CONNECTION

22-001www.powercommander.com 2009 Yamaha R6S PCV - 3

1 Remove the main seat and the passenger seat.

2 Prop the front of fuel tank up.

3 Remove the rubber plug in the tail section near the tool kit.

4 Lay the PCV unit in the tail section and route the harness thru the hole and

down the right side of the bike (Fig. A)

5 Route the PCV harness under the cross member for the subframe (Fig. B).

6 Attach the ground wire of the PCV to the negative side of the battery (Fig. B).

7 Unplug the 2 different 6 pin connectors from the throttle bodies (Fig. C).

One plug is BLACK and the other is CLEAR

FIG.A

FIG.C

FIG.B

PCV harness

Ground wire

Unplug

22-001www.powercommander.com 2009 Yamaha R6S PCV - 4

8 Plug the PCV connectors in-line of the throttle bodies and main wiring harness

(Fig. D). Plug the colored connectors from the PCV into the matching stock

connectors.

FIG.D

9 Secure the PCV unit in the tail section using the supplied velcro (Fig. E).

Make sure to clean both surfaces with the alcohol swab before attaching

10 Bolt the fuel tank back into place and reinstall the seats.

FIG.E

Altri manuali per Power commander V

Altri manuali Dynojet Accessori per motociclette

Dynojet

Dynojet POWER COMMANDER III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III 718-411 Manuale utente

Dynojet

Dynojet POWER COMMANDER FC Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III USB 109-411 Manuale utente

Dynojet

Dynojet Power Commander V Ex Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power Commander 3r Manuale utente

Dynojet

Dynojet Power commander V Guida rapida

Dynojet

Dynojet Power Commander III 705-411 Manuale utente

Dynojet

Dynojet POWER COMMANDER III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power commander V Manuale utente

Dynojet

Dynojet Power Commander III Manuale utente

Dynojet

Dynojet Power Commander FC Manuale utente

Manuali Accessori per motociclette popolari di altre marche

SRC

SRC B-TRK502-01-01-SL Manuale utente

3M Speedglas 9100 MP Manuale utente

hepco & becker

hepco & becker 6307520 00 01 Manuale utente

HOMCOM

HOMCOM AA0-077 Manuale utente

hepco & becker

hepco & becker 6307558 00 01 Manuale utente

Wunderkind Custom

Wunderkind Custom 106503-F15 Guida utente

Dräger

Dräger HPS 3500 Manuale utente

M-WAVE

M-WAVE SKI Manuale utente

Kuryakyn

Kuryakyn 6212 Manuale utente

hepco & becker

hepco & becker 6507504 00 01 Manuale utente

Tool it

Tool it PROMAX LCD 9.13G Manuale utente

Custom Dynamics

Custom Dynamics TruWrapz Manuale utente

Roof

Roof RO200 CARBON Manuale utente

Kabuto

Kabuto Japan IBUKI Manuale utente

PUIG

PUIG 5051 Manuale utente

rizoma

rizoma ZTH050 Manuale utente

Joubert

Joubert 10001711 Manuale utente

Sperian

Sperian Optrel p420 Manuale utente