EOS ECON L09 Manuale utente

Druck-Nr. 29343281en 37.06

Installation and User's Guide

ECON L09

IP x4

Installation guide for power control unit 9 kW

The power control unit is delivered equipped for a voltage of 380 - 400 V AC 3N with a

maximum breaking capacity of 9 kW and with a safety shutdown in connection with our

sauna control unit as standard.

Installation and connection of the sauna systems and other electrical equipment

may be undertaken only by an expert; please note that this is subject to VDE 0100,

Part 703/2006-02. Sauna systems may be connected to the power supply only by

hard wire.

Before the power control unit can be

fastened to the outer wall of the cabin, the

covering of the control unit must be

removed. For this, the two mounting

screws (Illust. 1) are loosened. These

screws are attached beneath the control

panel dials as captive screws, but may be

screwed open and closed through the vi-

sible holes in the operating panel with a

small Phillips screwdriver. After the screws

are loosened, the cover is removed.

Please observe that most sauna cabins

have already been equipped with cable

conduits for electrical wiring; in this case,

the position of the unit is pre-determined.

For the mounting of the unit, the mounting

holes Ø 3 are drilled in accordance with

the dimensions given in Illust. 3, and one

of the provided wood screws 4 x 20, see

Illust. 3.1, is screwed into the wood through

the upper middle hole, leaving a 3mm

section of the screw projecting out from the

wall. The lower part of the unit is hooked

onto this wood screw by its upper mounting

hole.

Finally all connecting lines (see Illust. 4)

are conducted through the respective feed-

through conduits into the control unit. The

lower part is finally fastened to the cabin

wall through the two lower pre-drilled holes.

Sauna

control unit

Power

control unit

Illust. 2

Mounting screws

Illust. 1

Eye level

Attention: It is forbidden to install the

control unit in a closed switch cabinet

or behind a wooden panelling!

approx. 20 cm

If the sauna cabin is not equipped with

cable conduits for the connecting lines,

these lines must be laid directly onto the

cabin wall, where they will be visible. For

this purpose, the three mounting holes

must be pre-drilled, as shown in Illust. 3.

Because the connecting lines must be laid

between the capacitor and the cabin wall

in this type of installation, for practical

purposes in a recess of the grooved

panels, the power control unit must be

installed in such a way as to provide for

adequate clearance. For this purpose, 3

spacer tubes are provided with the unit.

Using these tubes, the lower part is

installed to provide for this clearance as

shown in Illust. 3.2. After the connecting

lines are fed through the respective feed-

through channels into the unit, bolt the

lower part, again with help of the spacers,

into the lower mounting holes on the cabin

wall.

The electrical installation may be

accomplished only by a certified electrician

subject to the regulations of the local po-

wer utility company and those of the VDE.

Illust. 3

Mounting hole

Mounting holes

Illust. 4

Feed-through

channel for power

supply lines

Feed-through

channel for oven

supply line

Illust. 3.2

Illust. 3.1

Attention!

Dear customer,

according to the valid regulations, the

electrical connection of the sauna heater

and the control unit has to be carried out

through the specialist of an authorized

electric shop.

We would like to mention to the fact that

in case of a warrenty claim, you are kindly

requested to present a copy of the invoice

of the executive electric shop.

Guarantee

The guarantee is taken over according to the

legal regulations at present.

Manufacturer’s warrenty

- The period of warrenty starts from the date

of purchase and lasts up to 2years for

commercial use and 3 years for private use.

- Always include the completed warrenty

certificate when returning equipment.

- The warrenty expires for appliances which

have been modified without manufacturer’s

explicit agreement.

- Damages caused by incorrect operation or

handling through non-authorized persons are

not covered under the terms of warranty.

- In the event of a claim, please indicate the

serial number as well as the article code

number and type name with expressive

description of the fault.

- This warrenty covers damaged parts but no

defects due to wear and tear.

In case of complaint please return the equipment

in its original packaging or other suitable

packaging (caution: danger of transport damage)

to our service department.

Always include the completed warrenty

certificate when returning equipment.

Possible shipping costs arising from the transport

to and from point of repair cannot be borne by

us.

Outside of Germany please contact your

specialist dealer in case of warranty claims.

Direct warranty processing with our service

department is in this case not possible.

Equipment start-up date:

Stamp and signature of the authorized

electrician:

Service address:

EOS-Werke Günther GmbH

Adolf-Weiß-Str. 43

35759 Driedorf-Germany

tel +49 (0)2775- 82 240

fax +49 (0)2775- 82 455

[email protected]

www.eos-werke.de

Wiring diagram

Caution! Maximum phase load 3 kW per phase

Power supply Saunaheater Control cable

Safety relay

Control relay

Indice

Altri manuali EOS Unità di controllo

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente