Extech Instruments 380366 Manuale utente

User's Manual

Autoranging Datalogging Insulation Tester

(Megohmmeter)

with PC Interface

Model 380366

Introduction

Congratulations on your purchase of the Extech 380366 Datalogging Insulation Tester.

The 380366 measures insulation resistance to 4000MΩand includes Continuity and

Voltage tests. The built-in datalogger remotely stores approx. 16,000 readings for later

transfer to a PC. The tester can also take and record readings to a PC in real time. This

professional tester, with proper care, will provide years of safe reliable service.

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Back to the Extech 380366Product Page

380366 V1.6 11/04

Safety

1. Circuits under test must be de-energized and isolated before connections are made

(except for voltage measurements).

2. Circuit connections must not be touched during a test. Use extreme caution when

working near bare conductors and bus bars. Accidental contact with conductors could

result in electrical shock.

3. Use caution when working near voltages above 60VDC or 30VACrms.

4. After insulation tests, capacitors must be discharged.

5. Test leads (including alligator clips) must be in good working order, clean and without

broken or cracked insulation.

6. When servicing, use only specified replacement parts.

International Safety Symbols

Caution, refer to this manual before using this meter

Dangerous Voltages

Meter is protected throughout by double or reinforced insulation

Specifications

General specifications

Display Backlit 3-3/4 digit (4000 count) LCD with analog indicator

Sampling rate 2.5 samples/sec. (digital); 10 samples/sec. (analog)

Audible Continuity Low resistance range with audible continuity < 40Ω

Over range indicator "OL” displayed when measurement exceeds range limits

Low battery indicator " - +" symbol displayed when battery voltage is low

Datalogger memory 16,000 readings

Datalogger Sample

Rate

Programmable: 1 to 65,400 sec/sample or single manual

record

Power source Eight 1.5V AA cells

Power consumption 20 to 90mA depending upon function (40 hours typical)

Environmental CAT III; Altitude: 2000 meters; for indoor use only

Operating conditions 32 to 104oF (0 to 40oC); < 80% RH

Storage conditions 14 to 140oF (-10 to 60oC); < 80% RH

Dimensions/Weight 7.5 x 5.5 x 3” (190 x 140 x 77mm) / 2 lbs (900g)

Environmental specifications

•Installation Category III 600V

•Pollution Degree 2

•Altitude up to 2000 meters

•Intended for indoor use only

380366 V1.6 11/04

Range Specifications

Resistance / Audible Continuity

Range Resolution Accuracy Max. open

circuit voltage Overload

Protection

400 Ω 0.1 Ω ±1%rdg + 5d 12.8V 220Vrms

Audible tone when Resistance <40Ω;

Short circuit current: 280mA (min. 200mA)

AC Voltage (40 to 500Hz)

Range Resolution Accuracy Input

impedance Overload

Protect.

600VAC 1V ±1.5%rdg + 3d 4.5MΩ750Vrms

Megohm (Auto Range)

Voltage Ranges Maximum

Resolution

Resistance

Accuracy

Voltage

Accuracy

250V +20% ~ -0%

500V +20%~ -0%

1000V

4, 40, 400,

4000MΩ1kΩ±3%rdg + 5d (<2000MΩ)

±5%rdg + 5d (>2000MΩ) +10%~ -0%

Voltage Range 1mA Test Current Short Circuit

Current

250V @250KΩ

500V @500KΩ

1000V

4000MΩ

@1MΩ

< 1.5mA

Note: Accuracies are specified as % reading + digits at (73°F ± 9°F) 23oC ±5oC < 80% RH

Meter Description

1. LCD Display

2. Megohmmeter TEST pushbutton

3. Test LOCK and DATA HOLD button

4. RECORD button

5. LCD Backlight / Wake button

6. Function select switch

7. Storage compartment

8. RS-232 interface jack

9. Test Lead input jacks (HI & LO)

10. Test Leads

380366 V1.6 11/04

Operation

Connecting Test Leads

For all functions (Megohmmeter, Resistance, Continuity and AC Voltage), connect the red

test lead to the HI terminal and the black lead to the LO terminal.

Test Lead Check

1. Connect the red test lead to the HI input terminal; black lead to the LO terminal.

2. Set the rotary switch to the resistance/ continuity position ( . Ω)

3. Touch the test lead tips together. Resistance should be less than 1Ωand the audio

tone should sound.

4. With the leads not touching, the display should read “-OL-“. (over range).

5. If any readings are displayed other than the readings just described, the test leads

should be considered faulty and must be replaced before using the meter. Failure to

do so could result in damage to equipment and electrical shock.

Insulation Resistance Measurements (Megohmmeter Tests)

1. Connect the red test lead to the HI input terminal; black lead to the LO terminal.

2. Set the rotary switch to the desired function.

3. Connect the tips of the test leads to the equipment under test.

4. Press and hold down the red TEST button. Release the test button to stop the test. The

meter will then hold the resistance reading. This is indicated by the H icon in the upper

left corner of the display.

5. To clear the display, press the LOCK/HOLD button twice.

Note that the charge stored on the device under test will be automatically discharged

when the testing process is finished

3-Minute Test

For hands-free operation, use the Test Lock feature.

1. Connect the red test lead to the HI input terminal; black lead to the LO terminal

2. Set the rotary switch to the desired function.

3. Connect the tips of the test leads to the equipment under test.

4. Press the LOCK button. The LOCK icon will be displayed. Press the red TEST button.

A 3-minute continuous test will begin. The red TEST button can be pressed at any

time to end the test. If the TEST button is not pressed the meter automatically stops

the test after 3 minutes. The meter will then hold the resistance reading. This is

indicated by the H icon in the upper left corner of the display.

5. To clear the display, press the LOCK/HOLD button twice.

Note: The symbol will appear in the upper right corner of the display and an audible

tone will sound whenever the high voltage is applied to the test leads.

Warning

Ensure that the circuit under test does not include componentsthat can be damaged by 1000VDC; such

devices include power factor correction capacitors, low voltage mineral insulated cables, electronic light

dimmers, and ballasts/starters for fluorescent lamps.

Warning: Do not perform Insulation Resistance measurements if AC Voltage is present on circuit under test.

380366 V1.6 11/04

Analog Bargraph Display

The bargraph can indicate up to 10GΩ. When the measured value is between 4GΩand

10GΩ, the LCD displays "-HI-". When the measured value is higher than 10GΩthe LCD

displays "-OL-".

Low Resistance and Audible Continuity Tests

WARNING

Do not run this test unless ACV = 0. Do not use this mode to check diodes.

1. Set the Rotary switch to the audible continuity/resistance position.

2. Connect the red test lead to the HI input terminal; black lead to the LO terminal.

3. Connect the tips of the test leads to both ends of the circuit under test and read the

resistance on the LCD.

4. When the resistance of a circuit is less than approx. 40Ωan audible tone will sound.

AC Voltage Tests

1. Set the Rotary switch to the red ACV position.

2. Connect the red test lead to the HI terminal and the black test lead to the LO terminal.

3. Connect the other end of the test leads to the circuit under test.

4. Read the voltage value on the LCD.

Data Hold Function

The Data Hold function freezes the displayed reading. Data Hold works automatically on

Insulation Resistance Measurements (Megohmmeter tests) but, for the other tests, the

user must press the HOLD key to freeze the meter reading. Press HOLD again to exit the

Data Hold mode.

Auto Power OFF Feature

After a 30-minute period of non-use, the meter automatically shuts down. This will

conserve battery life. To wake the meter, press the Backlight button.

Note that the meter is not completely off until the function switch is set to the OFF position.

Always turn the switch to the OFF position when not in use.

Application Note for Large Installations

In large wiring installations where the insulation of outlets is being tested, more than one

insulation resistance measurement may have to be made to take into account parallel

resistances. Divide large systems into subgroups and test subgroups individually. Also, in

large installations, the capacitance of the insulation will be high, thereby taking longer to

charge when being tested. Care must be taken not to finish a measurement until the

insulation capacitance is fully charged (a steady, stable reading is an indication that this is

the case). The charge stored in the insulation after a test will be discharged automatically

when the test button is released. Be careful not to turn the range switch while the test

button is pressed.

380366 V1.6 11/04

Built-in Datalogger

The meter can store approx. 16,000 readings in the built-in datalogger. Readings are

grouped in ‘SETS’. Each recording session constitutes a ‘SET’. Recording a new set does

not erase a previously recorded set.

The readings remain in the datalogger memory even when power to the tester is off (as

long as the batteries are fresh). Readings can be transferred, at a later time, to a PC. Use

the meter’s RECORD button to operate the meter’s Datalogger in the following ways:

a. Clearing Datalogger memory

1. Press and hold the RECORD button while turning the meter on.

2. Release the RECORD button when r(clear) appears on the display. The entire

datalogger memory will now be erased.

b. Capturing one data point

Press the RECORD button for one second to capture one reading. The REC display

icon will briefly appear at the top of the LCD and the large digits will flash the data point

number (the recorded measurements are numbered). Each reading captured by this

method is considered a Set.

c. Capturing a continuous stream of data points

1. Press and hold the RECORD button for approx. 3 seconds until a long tone is heard.

The REC display icon will appear and remain on the display for as long as the

recording session lasts.

2. To stop recording, press the RECORD button again. The REC indicator will switch

off. Each group of readings captured in this manner is considered a Set.

3. Readings will be taken every 2 seconds (default sampling time). To change the

sampling time, refer to the section ‘Datalogger Software Mode’.

The following sections cover meter-to-PC data downloading & other PC interface features.

380366 V1.6 11/04

PC Interface

Minimum hardware requirements

486 PC or better with CD-ROM drive

Communications Settings

Baud Rate: 9600, Parity: None, Data bits: 8, Stop bits: 1

Connecting the meter to a PC

Connect one end of the supplied cable to the PC Com Port (DB9 connector) and the other

end (infrared connector) to the top of the meter.

Installing Software (compatible operating systems: WindowsTM 95, 98, 2000, Me, & XP)

1. Insert the supplied CD-ROM in the PC’s CD-ROM drive.

2. The SETUP program will run automatically. If not, press the WindowsTM START key

and select RUN. Then type SETUP at the prompt and press the ENTER key.

3. Follow the on-screen instructions for the setup program.

Running the Software

1. Open the ‘Insulate’ program using the program icon.

2. Select PC communications port COM1 or COM2 when prompted.

3. The Program screen will appear as a facsimile of the meter's front panel (see below).

Data Acquisition and Datalogger modes

These two modes of operation, distinctly different, are explained in detail separately.

For the Data Acquisition mode of operation, the meter must be connected to the PC. In this

mode, readings taken by the meter are displayed and stored on the PC.

In the Datalogger mode, the meter records data remotely then, at a later time, the meter is

connected to the PC and the readings are transferred. Instructions for datalogging were

covered in the previous section. Instructions for transferring data and navigating the

software are given below.

Control

Icons

Meter

buttons

Meter

display

System

Time

Sampling

Time

Function

Switch

Com.

Status

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

380366 V1.6 11/04

Data Acquisition Software Mode

As explained above, the Data Acquisition feature allows the user to connect the meter to

the PC and take and record readings simultaneously. With the meter connected to the PC

and with the software running, follow the steps below:

System Time Set

Click the computer icon from the row of Control Icons at the top of the main software

screen. This is the SYSTEM TIME SET button. The PC system date and time will now be

shared by the software program. Note that if your PC date and time are not set correctly,

do so at this time. The system time will be shown on the main software screen.

Input ID Code

The ID Code is used as a reference number specific to a particular data acquisition

session. The ID Code does not affect the software other than allowing the user to match a

set of data to a unique ID. See the LOGGER screen at right

1. Select MEMORY from the OPTION menu

on the main software screen.

2. Highlight the number in the ID Code field

and type a new reference number. Valid

numbers are 0 through 9999.

3. Click the ID Code button.

Sampling Time

The Sampling Time tells the software how

often to log a reading. The sampling time can

be set from 1 to 65,400 seconds. See the

LOGGER screen at right.

1. Click on the ‘wrist-watch’ icon from the

row of Control Icons on the main

software screen.

2. Highlight the existing value in the

SAMPLING field.

3. Type in the desired sampling time.

4. Click the Sampling button when finished.

Creating a File to store data

1. Click the ‘floppy disk’ icon from the row of Control Icons on the main software screen

and type a unique filename when prompted.

2. This File can later be opened by clicking on the ‘folder’ icon (4th from left) from the row

of Control Icons on the main software screen.

3. Saved files can be opened in spreadsheet programs as *.dat text files by opening the

spreadsheet application, selecting OPEN FILE, choosing ALL FILE TYPES, and

locating the file previously stored.

Start and Stop Recording

1. Click the ‘red’ icon (2nd from left) from the row of Control Icons on the main software

screen to start recording. If a file has not been set up at this point, the software will

prompt for a file name.

2. Data will now be logged every nseconds (where nis the programmed sampling time).

3. To stop recording, click the ‘black’ icon (3rd from left) in the row of Control Icons.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

380366 V1.6 11/04

Open an existing Data File

1. Click on the ‘folder’ icon (4th from left) in the row of Control Icons on the main software

screen.

2. Select a file from the list of

previously stored files (if any).

3. When a file is opened, its data list

will appear containing the date/time

for each reading, measurement, unit

of measure, and low battery

indication (see diagram at right).

4. Select PRINT from the menu

heading to print the data list.

5. To import the data to spreadsheet or

other 3rd party application: Locate

and open the file as a text file

(filename.dat) using the FILE OPEN

commands in the 3rd party

application.

Soft-key Remote Control

Use the four front-panel keys on the main software screen to remotely control the meter:

TEST button

Click to start a megohmmeter test.

LOCK button

Click to lock the test for 3 minutes (read about the LOCK function earlier in this manual).

HOLD button

Click to freeze the displayed reading. The ‘H’ display icon will appear while the meter is in

the Data Hold mode. Press HOLD again to exit this mode.

REC button

Click to put the meter into continuous recording mode. Readings will be kept in the open

file. If a file is not open, the software will prompt for a file name.

rec button

Click to record one reading to the open file.

Backlight button

Click to activate the meter’s display backlight.

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Back to the Extech 380366Product Page

380366 V1.6 11/04

Datalogger Software Mode

Datalogging

Instructions for storing data in the meter’s built-in datalogger are provided in the ‘Built-In

Datalogger’ section of this manual.

The following section details all of the datalogger functions available in the supplied

software.

Datalogging Software Window (LOGGER)

1. From the main software screen, click the ‘datalog’ icon (3rd from right) from the row of

Control Icons. The LOGGER window will open (shown below).

2. To set the SAMPLING TIME (rate at which datalogger stores readings), type a number

between 1 and 65,000 seconds in the SAMPLING field. Note that the meter must be

connected to the PC in order for the Sampling Time to be transferred to the meter.

Once the sampling time is set, the meter will datalog at the rate selected.

3. Click the TIME OF RECORDING button to download all of the data sets from the meter

to the PC. The data lists will appear as shown on the logger window diagram below.

4. Select a set of data by clicking on the set number. The NUMBER OF SET field informs

the user as to which set is selected. The NUMBER OF RECORDS field lets the user

know the number of readings in the selected set.

5. The MEMORY and REMAINING fields inform the user as to the total memory capacity

(32K) and the remaining memory.

6. Press the SHOW DATA button to view the raw data. Once the data opens for the

selected set, the user can save or print the data by selecting SAVE or PRINT from the

menu options.

Size of

overall

memory

System

Date &

Time

Number of data

sets in memor

Number of

records in

selected set

Click to view

data for the

selected set

Remaining

storage space

User ID Code

& Sample rate

Click to

download all

stored sets

List of all

loaded sets

Click a

number to

select a set

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Indice

Altri manuali Extech Instruments Apparecchiature di prova

Extech Instruments

Extech Instruments MG320 Manuale utente

Extech Instruments

Extech Instruments 480303 Manuale utente

Extech Instruments

Extech Instruments CG204 Manuale utente

Extech Instruments

Extech Instruments HDV700 Manuale utente

Extech Instruments

Extech Instruments 412300A Manuale utente

Extech Instruments

Extech Instruments 382357-NIST Manuale utente

Extech Instruments

Extech Instruments HDV540 Manuale utente

Extech Instruments

Extech Instruments IRC350 Manuale utente

Extech Instruments

Extech Instruments ET10 Manuale utente

Extech Instruments

Extech Instruments 380385 Manuale utente

Extech Instruments

Extech Instruments 7630 Manuale utente

Extech Instruments

Extech Instruments 380395 Manuale utente

Extech Instruments

Extech Instruments GX930 Manuale utente

Extech Instruments

Extech Instruments CG304 Manuale utente

Extech Instruments

Extech Instruments PRC30 Manuale utente

Extech Instruments

Extech Instruments MG325 Manuale utente

Extech Instruments

Extech Instruments CB10 Manuale utente

Extech Instruments

Extech Instruments 407744 Manuale utente

Extech Instruments

Extech Instruments BR50 Manuale utente

Extech Instruments

Extech Instruments PRC10 Manuale utente

Extech Instruments

Extech Instruments BR90 Manuale utente

Extech Instruments

Extech Instruments RT30 Manuale utente

Extech Instruments

Extech Instruments 433201 Manuale utente

Extech Instruments

Extech Instruments 7470 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente