Extech Instruments 433201 Manuale utente

1 433201 Ver. 1.5 11/03

User's Guide

Microprocessor Calibrator/Thermometer

Model 433201 and 433202

Introduction

Congratulations on your purchase of Extech's 433201 (115V) or 433202 (220V)

Microprocessor Thermocouple Calibrator/Thermometer. A precision millivolt signal is

either input from a thermocouple (“Measure” mode”) or output to another thermocouple

device (“Calibrate” mode) and the corresponding temperature, according to standard

temperature tables, is displayed on the meter’s 4 digit LED display.

2 433201 Ver. 1.5 11/03

Specifications

Calibrate & Measure Resolution Accuracy

Type J -58 to 1830OF (-50 to 1000OC)

Type K -58 to 2498OF (-50 to 1370OC)

Type T -184 to 752OF (-120 to 400OC)

Type E -58 to 1382OF (-50 to 750OC)

0.1Oto 999.9O

1Oabove 999.9O

Type C 32 to 4172OF (0 to 2300OC)

Type R 32 to 3182OF (0 to 1750OC)

Type S 32 to 3182OF (0 to 1750OC)

Type N -58 to 2372OF (-50 to 1300OC)

1.0°

±(0.15% rdg + 1.8OFor1OC)

Voltage -5.00mV to +55.00mV 10µV ±(10µV + 1 digit)

Cold junction compensation 0.03OC/OC (0.02OF/OF)

Input impedance 10MΩ

Sampling time 4 times / second

Display 4 digit LED

Description

1. LED display

2. TYPE button

3. °C/°F button

4. COARSE output adjust

5. Battery compartment

6. Output/Input mini connector

7. Measure/Calibrate switch

8. FINE output adjust

9. AC Adaptor connector

10. On/Off switch

3 433201 Ver. 1.5 11/03

Operation

MEASURING TEMPERATURE

1. Press the red power switch to the ON position.

2. Select the “MEASURE” mode on the side panel slide switch

3. Select the thermocouple type of your measuring probe via the faceplate “TYPE”

button. An LED will light above the T/C type selected in the display. Each time

the “TYPE” button is pressed the indicator will advance one type.

4. Select

°C or °F via the “C/F” button.

5. Insert the thermocouple probe into the sub-miniature female connector on the

side panel. Be sure to check that it is inserted with the proper polarity and make

sure the proper type is selected in the display.

6. Read the temperature on the LED display.

CALIBRATING THERMOCOUPLE DEVICES

1. Press the red power switch to the “ON” position.

2. Select the “CALIBRATE” mode on the side panel slide switch.

3. Select the thermocouple type of the device to be calibrated via the faceplate

“TYPE” button. An LED will light above the T/C type selected in the display.

Each time the “TYPE” button is pressed the indicator will advance one type.

4. Select

°C or °F via the “C/F” button.

5. Insert the calibration cable into the sub-miniature female connector on the side

panel. Be sure to check that it is inserted with the proper polarity and make sure

the proper type is selected in the display.

Note: For greater accuracy, especially if there is a difference between the internal

temperature of the calibrator and the device under calibration, we recommend that you use

a thermocouple cable rather than the copper cable that is supplied with the calibrator. The

thermocouple cable must match the thermocouple type of the device under calibration.

6. Connect the other end of the cable to the device to be calibrated.

7. Allow the proper warm up time for the Calibrator and the Device to be calibrated.

At least 30 minutes is typically recommended.

8. Adjust to the desired output temperature using the up/down “COARSE”

adjustment buttons on the faceplate and the “FINE” adjustment knob on the side

panel. The output temperature will be displayed on the LED display. The

“COARSE” adjustment has 16 increments and will display “high” or “low” when

out of range.

DIRECT mV CALIBRATION and MEASUREMENT

For directly calibrating or measuring thermocouple devices in mV rather than in

temperature, press the “TYPE” button until the F or C in the LED display disappears (only

the “O” remains). The LED display will now indicate in mV rather than temperature units.

4 433201 Ver. 1.5 11/03



Support Hotline (781) 890-7440

Tech support: Ext. 200; Email: [email protected]

Repair/Returns: Ext. 210; Email: repair@extech.com

Website: www.extech.com

BATTERY

WARNING: DO NOT CONNECT THE AC ADAPTOR TO THE METER IF A 9V

ALKALINE BATTERY IS INSTALLED.

For continuous use the AC/DC Adaptor/Recharger.

For portable operation use the 8.4V NiCad battery.

Replace batteries using the following procedure:

Close the case and insert a coin or flat screwdriver into the slot at the top of the meter.

Snap the cover in the direction of the arrow and then open the cover of the meter.

Remove the battery cover and connect the snap terminals to the battery terminals.

Close the battery cover firmly.

Charge the battery for 24 to 48 hours before its first use. An overnight charge will enable

continuous use for approximately 45 minutes. A full charge will provide one hour of

continuous use.

Turning the meter OFF when not in use will prolong battery life.

A 9V alkaline battery may be used in place of the rechargeable (8.4V) NiCad battery that

comes with the unit.

A flashing “F” or “C” on the LED display indicates a low battery condition.

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and

workmanship for one year from date of shipment (a six month limited warranty applies on sensors and

cables). If it should become necessary to return the instrument for service during or beyond the warranty

period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our

website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA

number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The

sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in

transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper

wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification.

Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and

will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited

to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty,

whether written or oral, is expressed or implied.

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also provides NIST certification for

most products. Call the Customer Service Department for information on calibration services available for this

product. Extech recommends that annual calibrations be performed to verify meter performance and accuracy.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extech Instruments Apparecchiature di prova

Extech Instruments

Extech Instruments 412355A Manuale utente

Extech Instruments

Extech Instruments FT10 Manuale utente

Extech Instruments

Extech Instruments ET10 Manuale utente

Extech Instruments

Extech Instruments SL120 Manuale utente

Extech Instruments

Extech Instruments RT30 Manuale utente

Extech Instruments

Extech Instruments CB10 Manuale utente

Extech Instruments

Extech Instruments 407744 Manuale utente

Extech Instruments

Extech Instruments MS6100 Manuale utente

Extech Instruments

Extech Instruments BR90 Manuale utente

Extech Instruments

Extech Instruments 380366 Manuale utente

Extech Instruments

Extech Instruments PRC30 Manuale utente

Extech Instruments

Extech Instruments CB10 Manuale utente

Extech Instruments

Extech Instruments 380363 Manuale utente

Extech Instruments

Extech Instruments 480303 Manuale utente

Extech Instruments

Extech Instruments ET30B Manuale utente

Extech Instruments

Extech Instruments 480403 Manuale utente

Extech Instruments

Extech Instruments ET26B Manuale utente

Extech Instruments

Extech Instruments ET28B Manuale utente

Extech Instruments

Extech Instruments CG304 Manuale utente

Extech Instruments

Extech Instruments 422123 Manuale utente

Extech Instruments

Extech Instruments PRC50 Manuale utente

Extech Instruments

Extech Instruments ET20B Manuale utente

Extech Instruments

Extech Instruments PRC15 Manuale utente

Extech Instruments

Extech Instruments 380385 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente