H3C LSQM1SDNB0 Manuale utente

Manual version: APW102-20191215 BOM: 3123A1VF

H3C LSQM1SDNB0 SDN automation module

1 Identifier

The module identifier LSQM1SDNB0 is in the upper right corner of the front panel.

2 About the module

The LSQM1SDNB0 is an SDN automation module built with server components required for

ADCampus solutions. Plug and play, it supports fully automated deployment at small and

medium-sized campus networks. It can deliver controller, authentication, and address assignment

functions, eliminating the need for installing physical servers.

Figure 1 LSQM1SDNB0 front panel

(1) USB ports (3 in total) (2) VGA connector

(3) Management Ethernet port (4) Management Ethernet port LED (LINK/ACT)

(5) Console port (CONSOLE) (6) Shutdown LED and button (SHUTDOWN)

(7) Ejector lever (8) Captive screw

3 Specifications

Table 1 Module specifications

Item Specifications

Hard disk 480GB SSD

Memory Two memory slots

Standard configuration: 64 GB (two 32GB memory bars)

Dimensions (H × W × D) 40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in)

Weight 3.40 kg (7.50 lb)

Power consumption 102 to 124 W

Hot swapping Not supported

Ports

•3 × USB2.0 ports (used by technical support for debugging only)

•1 × VGA connector

•1 × 10/100/1000BASE-T management Ethernet port

•1 × console port (used by technical support for debugging only)

Ambient temperature •Operating: 0°C to 45°C (32°F to 113°F)

•Storage: –40°C to +70°C (–40°F to +158°F)

Manual version: APW102-20191215 BOM: 3123A1VF

Item Specifications

Ambient humidity •Operating: 5% RH to 95% RH, noncondensing

•Storage: 5% RH to 95% RH, noncondensing

NOTE:

•To verify the compatibility of the card with the software release you are using, see the release

notes.

•For information about transceiver modules and cables available for the card, see the cards and

transceiver modules compatibility matrixes for the device.

Table 2 10/100/1000BASE-T management Ethernet port specifications

Item Specification

Standard 802.3, 802.3u, and 802.3ab

Auto-MDI/MDIX Supported

Cable Category 5 or above twisted pair cable

Transmission distance 100 m (328.08 ft)

Rate and duplex mode 10/100/1000 Mbps, full-duplex

4 LEDs

Table 3 LED description

LED Status Description

10/100/1000BASE-T

management Ethernet port

LED (LINK/ACT)

Steady green A 10/100/1000M link is present on the port.

Flashing green The port is sending or receiving data at 10/100/1000

Mbps.

Off No link is present on the port.

Shutdown LED

(SHUTDOWN)

Steady green The module is operating.

Flashing green The module is being shut down. You can shut down the

module only after the LED turns off.

Off The module is not operating.

5 Installing and removing the module

CAUTION:

•Wear a reliably grounded ESD wrist strap or ESD gloves when installing or removing the module.

•Do not touch the components on the module.

The module can be installed in a horizontal or vertical slot. When installing the module in a horizontal

slot, make sure its component side faces up. When installing the module in a vertical slot, make sure

its component side faces left.

The installation and removal procedures are the same for horizontal and vertical slots. The following

procedures install and remove the module in a horizontal slot.

Manual version: APW102-20191215 BOM: 3123A1VF

iii

5.1 Installing the module

1. Face the front panel of the device. Remove the filler panel from the target slot.

This example installs the module in slot 2 on an S7506E switch.

2. Place the module on a workbench with its component side facing up. Open the ejector levers of

the module.

3. Gently push the module into the slot along the guide rails.

4. Close the ejector levers and make sure the module makes close contact with the backplane.

5. Use a Phillips screwdriver to fasten the captive screws on the module.

Figure 2 Installing the module

5.2 Removing the module

IMPORTANT:

Before removing the module, press the shutdown button on the module for a minimum of 2 seconds

until the shutdown LED flashes green. You can remove the module only after the shutdown LED

turns off.

To remove the module:

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously open the ejector levers of the module to disengage the module connector from

the backplane. Then pull the module gently out of the slot along the guide rails.

3. Place the removed module on an anti-static workbench or put it in an anti-static bag, with the

component side facing up.

4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

Manual version: APW102-20191215 BOM: 3123A1VF

6 Software upgrade

For information about upgrading the software, see the release notes for the module.

The information in this document is subject to change without notice.

Indice

Altri manuali H3C Unità di controllo

H3C

H3C PSR750-A Manuale utente

H3C

H3C PSR2400-12AHAH-B Manuale utente

H3C

H3C PSR360-56A Manuale utente

H3C

H3C LSBM1WCM2A0 Manuale utente

H3C

H3C EWPA1PCID Manuale utente

H3C

H3C SecPath M9000-AI NSQM5MBSHA1 Manuale utente

H3C

H3C NSQ1TGS32SF0 Manuale utente

H3C

H3C R6900-FAN Manuale utente

H3C

H3C S12500 LST1LB1A1 Manuale utente

H3C

H3C SR6600 SPE-FWM-200 Manuale utente

H3C

H3C PSR250-12A Manuale utente

H3C

H3C PSR450-12A Manuale utente

H3C

H3C SecPath M9000 NSQM1CGQ20 Manuale utente

H3C

H3C SecPath NSQ1FAB08D0 Manuale utente

H3C

H3C MSR Router Comware 5 Series Manuale utente

H3C

H3C PSR150-A1 Manuale utente

H3C

H3C LSUM1TGT24FD0 Manuale utente

H3C

H3C PSR650C-12A Manuale utente

H3C

H3C SIC-4G-LTE-M Istruzioni operative e di manutenzione

H3C

H3C SecBlade Manuale utente

H3C

H3C S9500E LSR1FW2A1 Manuale utente

H3C

H3C SecPath M9000 NSQM1MBFEA0 Manuale utente

H3C

H3C SecPath NSQM2AC1400 Manuale utente

H3C

H3C SFP-GE-SX-MM850-A Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente