H3C PSR180-56A Manuale utente
1
H3C PSR180-56A Power Module
User Manual-6PW101
BOM: 3101A0LW
Power module overview
PSR180-56A is a DC-output power module that supports both AC
and DC input. It provides a maximum output of 184 W.
The power module supports 1+1 redundancy and load sharing and is
hot swappable. It also provides overcurrent, undervoltage,
overvoltage, short circuit, overtemperature, output current limiting
protections.
Technical specifications
Table 1 Technical specifications
Item Specifications
Rated input voltage
•AC: 100 VAC to 240 VAC @ 50
Hz or 60 Hz
•DC: 240 VDC
Maximum input voltage
•AC: 85 VAC to 290 VAC @ 47 Hz
to 63 Hz
•DC: 180 VDC to 320 VDC
Maximum input current •AC: 2.5 A
•DC: 1.5 A
Output voltage 56 V
2
Item Specifications
Output current 3.3 A
Maximum output power 184 W
Dimensions (H × W × D) 40.1 × 82.6 × 259.5 mm (1.58 × 3.25
× 10.22 in)
Operating temperature –10°C to +55°C (14°F to 131°F)
Relative humidity 5% to 95%, noncondensing
Appearance
Figure 1 Appearance
(1) Input status LED (IN OK) (2) Power receptacle
(3) Latch (4) Handle
(5) Output status LED (OUT OK)
3
LEDs
Table 2 LED description
LED Status Description
Input status
LED (IN OK)
Steady green The power input is normal.
Off No power input or the power
input is abnormal.
Output status
LED (OUT
OK)
Steady green The power output is normal.
Steady red The power output is abnormal.
Off No power output.
Installing and removing the power
module
Safety precautions
To avoid possible bodily injury and power module and device
damage, follow these safety precautions:
•When you install and remove the power module, always wear
an ESD wrist strap and make sure it makes good skin contact
and is reliably grounded.
•Before you install the power module, make sure the voltage of
the power source is as required by the power module, and the
output voltage of the power module is as required by the device.
•Do not touch any cables or terminals of the power module.
•Do not place the power module in a wet area, and prevent liquid
from flowing into the power module.
4
•To avoid power module damage, do not open the power module.
When the internal circuits or components of the power module
fail, contact H3C Support.
Tools
Prepare an ESD wrist strap and a flat-blade screwdriver yourself.
Installing and removing the power module
Make sure the power module model is compatible with the device.
For more information about hardware compatibility, see the
installation guide for the device.
Installing the power module
To avoid bodily injury or device damage, follow the procedure
in Figure 2 to install the power module.
Figure 2 Installation procedure
To install the power module:
1. Wear an ESD wrist strap and make sure the strap makes good
skin contact and is reliably grounded.
2. Unpack the power module and verify that the power module
model is as required.
3. Remove the filler panel as shown in Figure 3, if any, from the
target power module slot.
{Put your finger into the hole in the filler panel and pull the
filler panel out along the guide rails.
5
{Insert a flat-blade screwdriver through the handle on the filler
panel and pull the filler panel out along the guide rails.
Figure 3 Removing a filler panel
4. Insert the power module into the slot, as shown in Figure 4:
a. Correctly orient the power module with the characters
upward.
b. Holding the power module handle with one hand and
supporting the power module bottom with the other, slide the
power module along the guide rails into the slot. When the
power module is completely inserted into the slot, you can
hear that the latch of the power module clicks into the slot.
If the power module is not aligned with the slot, pull out the
power module, adjust its direction, and insert it again.
1 2
6
Figure 4 Installing the power module
IMPORTANT:
Keep the filler panel and the packaging box and packaging bag
of the power module for future use.
Connecting the power cord
WARNING!
•Make sure the power cord has a separate circuit breaker.
•Turn off the circuit breaker before connecting the power
cord.
IMPORTANT:
Use the power cord provided with the power module. The powe
r
cord uses a C13 connector.
To connect the power cord:
1. As shown in Figure 5, plug the female connector end of the
power cord into the power receptacle on the power module.
7
2. Use a cable tie to secure the power cord to the handle of the
power module.
Figure 5 Securing the power cord
3. Connect the other end of the power cord to the power source,
and turn on the circuit breaker.
4. Examine the IN OK LED on the power module. If the LED is
steady green, the power cord is connected correctly. If the LED
is off, examine the installation, troubleshoot the problems, and
try again until the LED is steady green.
Removing the power module
To avoid bodily injury or device damage, follow the procedure
in Figure 6 to remove the power module.
Figure 6 Removing procedure
To remove the power module:
1. Turn off the circuit breaker at the power input end.
8
2. Wear an ESD wrist strap and make sure the strap makes good
skin contact and is reliably grounded.
3. Loosen the cable tie and remove the power cord.
4. As shown in Figure 7, press the latch towards the handle, and
pull the power module part way out of the slot along the guide
rails.
5. Holding the power module handle with one hand and supporting
the power module bottom with the other, pull the power module
slowly out of the slot along the guide rails.
6. Put the removed power module on an antistatic mat or into its
package.
7. If you are not to insert a power module into the empty slot, insert
the filler panel into the slot to prevent dust from entering the
chassis.
Figure 7 Removing the power module
Copyright © 2017 New H3C Technologies Co., Ltd.
1
2
Indice
Altri manuali H3C Unità di controllo
H3C
H3C R6900-FAN Manuale utente
H3C
H3C Campus SeerEngine LSXM1SEERBXC2 Manuale utente
H3C
H3C SFP-GE-SX-MM850-A Manuale utente
H3C
H3C SR6600 SPE-FWM Manuale utente
H3C
H3C SecPath PSR300-12A2 Manuale utente
H3C
H3C NSQ1TGS32SF0 Manuale utente
H3C
H3C SecPath M9000-AI NSQM5AIASKA1 Manuale utente
H3C
H3C SecPath AC2500 Manuale utente
H3C
H3C SecPath DC2400 Manuale utente
H3C
H3C LSUM1TGT24FD0 Manuale utente
H3C
H3C MSR Router Comware 5 Series Manuale utente
H3C
H3C LSQM1SDNB0 Manuale utente
H3C
H3C SecPath NSQM2GP24TSSC0 Manuale utente
H3C
H3C PSR250-12A1 Manuale utente
H3C
H3C SecPath PSR300-12A2 Manuale utente
H3C
H3C EWPA1PCID Manuale utente
H3C
H3C S9500 LSB1LB1A0 Manuale utente
H3C
H3C SR6600 SPE-FWM-200 Manuale utente
H3C
H3C LSVM2106SFAN Manuale utente
H3C
H3C PSR1800-56A Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
