ICP DAS USA TM-AD8C Manuale utente

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

tM-AD8C

8-channel Isolated Current Analog Input

Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/tm_ad8c.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The tM-AD8C is an current input module that includes 8 single-ended analog input

channels and provides a programmable input range on all analog inputs (0 ~ 20 mA, 4 ~

20 mA). The sampling rate of the tM-AD8C is adjustable and is available in either fast or

normal mode and It also provides 4 KV ESD protection as well as 2500 Vrms intra-

module isolation.

2. Terminal Assignment

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

Use 26-12 AWG wire for signal connections.

Strip the wire to a length of 7±0.5mm.

Use a crimp terminal for wiring.

Avoid high-voltage cables and power equipment as much as possible.

For RS-485 communication, use insulated and twisted pair 24 AWG wire, e.g.

Belden 9841.

4. Default Settings

Default settings for the tM AD modules are as follows:

。Protocol: Modbus RTU

。Module Address: 01

。Analog Input Type: type code 08, -10V to 10V

。Baud Rate: 9600 bps

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the analog current input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

tM-AD8C 8-channel Current Analog Input Module- QuickStart (Jun/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. The Modbus RTU communication protocol is the default protocol of the tM series.

The communication Baud Rates for the Modbus RTU protocol can be in the range of

1200 bps to 115200 bps

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA PM-4324 Series Manuale utente

ICP DAS USA

ICP DAS USA LP-8 21 Series Manuale utente

ICP DAS USA

ICP DAS USA I-2533 Manuale utente

ICP DAS USA

ICP DAS USA I-8124W Manuale utente

ICP DAS USA

ICP DAS USA I-7063 Manuale utente

ICP DAS USA

ICP DAS USA tPET-P2R2 Manuale utente

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 Manuale utente

ICP DAS USA

ICP DAS USA ZT-2510 Series Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2012H Manuale utente

ICP DAS USA

ICP DAS USA LP-8 4 Series Istruzioni generali

ICP DAS USA

ICP DAS USA SG-785 Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2000 Series Manuale utente

ICP DAS USA

ICP DAS USA tM-TH8 Manuale utente

ICP DAS USA

ICP DAS USA M-7067D Manuale utente

ICP DAS USA

ICP DAS USA EIP-2060 Manuale utente

ICP DAS USA

ICP DAS USA ET-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7002 Manuale utente

ICP DAS USA

ICP DAS USA ET-7000 series Manuale utente

ICP DAS USA

ICP DAS USA tET Series Manuale utente

ICP DAS USA

ICP DAS USA I-8088W Manuale utente

ICP DAS USA

ICP DAS USA tM-P3R3 Manuale utente

ICP DAS USA

ICP DAS USA M-7033D Manuale utente

ICP DAS USA

ICP DAS USA I-7083 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

ICP DAS USA tM-AD8C Manuale utente

Manuali Unità di controllo popolari di altre marche