JAC Varia Pro Manuale utente
VARIA PRO
3
MACHINES À COUPER LE PAIN
(Notice d’instructions originale
11
BREAD SLICERS
(Translation of the original instructions
5
EN
ENEN
EN
FR
FRFR
FR
V01.130912
Translation of the original instructions
4
5
BEFORE START-UP
WARRANTY
You have just received a JAC machine and we would li e to than your very much for your
confidence.
In order for you to be completely satisfied over the next few years, please note the following
advices :
- Obtain assistance from your authorised agent for installation, start-up and follow-up ;
- In order to be able to benefit from the 3 year warranty (see conditions for returning be-
low), you should have the service boo filled out by your distributor when the machine is
installed. The service boo is located at the bac of this manual.
JAC offers a 3 year warranty on all its products.
This warranty includes replacement of original parts found to be defective and installation
free of charge by the JAC agent.
The warranty becomes effective from the installation date of the equipment
Under the following restrictive conditions :
1. The equipment is purchased under “normal“ conditions ;
2. Installation is made by an authorised agent ;
3. Utilisation of equipment conforming to the indications of the instructions for use and for
the purpose for which it is made ;
4. The equipment is maintained daily as a good father should and with all due care ;
5. Maintenance followed-up by the authorised agent conforming to the maintenance speci-
fications with at least one maintenance a year (maintenance at the user’s cost).
The manual has a page for this where the agent can detail the different maintenance.
If there is no maintenance follow-up by an authorised agent and/or if the service
book is not completed correctly, the warranty is limited to one year.
6. Exclusive use of JAC original parts.
This warranty doesn’t cover :
1. Replacement of normally wearing parts ;
2. Parts found not to be defective by our dealers ;
3. Problems resulting from abnormal use of the equipment ;
4. Problems resulting from an installation not installed by an authorised agent ;
5. Parts where problems result from transport damage or incorrect handling.
Repair and/or replacement of defective parts during the warranty period does not extend the
initial warranty.
6
CAUTION
START-UP
- If necessary fix the feet or casters (if with stand) delivered with the machine ;
- Chec the direction of the blade rotation; if necessary reverse 2 phase wires ;
- Please refer to the “Instructions for use” section for using the machine.
CONNECTION
- Before connecting your machine to the electricity networ , chec that the machine oper-
ation voltage (see rating plate on the machine) and voltage of the electricity networ
are appropriate ;
- Connection of the machine has to be made using an earthed plug ;
- Your electrical installation supplying the machine has to be protected as below :
- North America : Main protection 15A ;
- Rest of the world : Main protection 16 A.
Note : All other problems resulting from another type of connection will not be ta en into
account.
- This machine is intended for professional ba ers ;
- This machine is solely intended for cutting temperate ba ed bread ;
- It may only be used by one person at a time. (unless otherwise stated) ;
- It has to be ept and used inside in a location, away from humidity and heat ;
- The machine has to be adequately lit for carrying out the wor satisfactorily ;
- This machine has a noise level below < 64,8 dB(A) ±5 dB(A) as per standard EN ISO
3746.
- For machines without special field sources: Non-ionizing radiation is not intentionally
produced, but only for technical reasons of the electrical equipment (such as electric
motors, power lines, or magnetic coils) only. In addition, the machine has no strong
permanent magnets. While maintaining a safe distance (distance to source field implant)
of 30 cm can be ruled out the influence of active implants (ex. pacema ers, defibrilla-
tors) with high probability.
7
Use the diagrams (page 16) to use the machine.
At the start of the day power up the machine with the aid of the main switch (located at the
bac side of the machine).
Procedure to use the machine :
1. Open the cover;
2. Put the bread on the right table;
3. Close the cover ;
4. Push on the rotary button to choose the thic ness from 6 to 25 mm (upper screen (B));
5. Push again on the rotary button (A) and choose the slicing type (lower screen (C)):
- 1 - 2 : Slicing in half ;
- ALL : Slicing all the bread ;
- 1 to 99 : Slicing of 1 to 99 slice needed.
6. Push on the green button (D) to start the slicing ;
7. When the green button flashing, open the cover to ta e you bread out and pac it.
Capacity :
Maximum size (Lengh x widht x height) (cm) : 42 X 29 X 14,5 ;
Capacity : 2.000 breads / day
Safety :
- Opening the crumb collector stops the machine from operating.
- Pushing on red button (E) stops the current slicing.
DANGER
- In case of danger for the user or for the machine, you must use the main switch to
switch off the electric supply of the machine ;
- Remove the electric plug before every maintenance and service operation ;
- Don’t touch the blade even when stopped ;
- If you need to change the blade, have this done by your authorised distributor ;
- Ma e sure that you wear anti-cut protective gloves and safety shoes
when replacing the cutters or carrying out operations in the vicinity of the blades ;
- All maintenance or part changing operations are to be carried out by a qualified person ;
INSTRUCTIONS FOR USE
8
MAINTENANCE
Daily, by a trained user :
1. Chec to see if the crumb collector needs to be emptied ;
NB: Do not forget to loc the door
2. Clean tables using a brush ;
3. Clean the optical sensor ;
4. Clean the glass cover :
- Close to half cover
- Unloc the hoo s on each side
- lift the hood to clean
- Close cover and loc the hoo s.
NB: Use a dry cloth to clean the inside.
5. For outside maintenance, use a damp cloth.
Every year, by an authorised agent :
1. Remove the plug ;
2. Chec the condition of the cutting blade. If a deterioration in the slicing quality is ob
served, you must proceed with replacing the cutting blade (JAC reference: 610022 of
the JAC Spare Parts Catalogue).
If the blade needs to be changed, replace it in accordance with the procedure for chang-
ing the cutting blade ;
3. Clean with a brush and vacuum the inside of the machine.
Check that your authorised agent records the intervention in your service book in
order to keep your 3 year warranty
9
HOW TO CHANGE THE BLADE
Always wear cut resistant protective gloves (EN 388 Standard: 2003 index level B = 5) and
safety shoes when replacing the blade or when carrying out an operation near the blade.
Once you have ensured that your machine is actually disconnected from the mains:
1. Open the left door ;
2. Remove the crumb collector ;
3. Replace the blade :
- Unscrew the nut that holds the blade, using the eys (2) provided ;
- Remove the wedge and replace the blade, ta ing care to place it properly in the
alignment eys ;
- Put the wedge bac ;
- Screw and tighten the nut to loc the blade, using the eys provided.
4. Replace the crumb collector and close the door.
Connect your machine to the electricity networ .
SPARE PARTS
When ordering spare parts, chec with your authorised agent the parts concerned using
the spare parts catalogue published by the manufacturer.
Always provide the machine number as indicated on the rating plate.
Your agent will order the parts from JAC.
The machine is completely stopped
Did you plug it in ?
Is the power supply coming to the soc et ?
Is the cover correctly closed ?
Is the front door correctly closed ?
The bread brea s
Do the cutters have to be replaced ?
Always get an authorised dealer to carry out maintenance work on your machine!
TROUBLESHOOTING
Notice d’instructions originale
10
Indice
Lingue:
Altri manuali JAC Elettrodomestico da cucina
JAC
JAC MB Manuale utente
JAC
JAC Duro 450 M Manuale utente
JAC
JAC Pico Series Manuale utente
JAC
JAC MODENA + Manuale utente
JAC
JAC ZIP Manuale utente
JAC
JAC DIVIFORM Manuale utente
JAC
JAC Varia Pro Series Manuale utente
JAC
JAC CHUTE+ Series Manuale utente
JAC
JAC Duro Series Manuale utente
JAC
JAC VARIA VMP800 Manuale utente
