Optika Italy ACCESSORIES Series Manuale utente
Ver. 2.1 2022
INSTRUCTION MANUAL
ACCESSORIES Series
Model
CLD-01
Page 2
Table of Contents
1. Warning 3
2. Safety Information 3
3. Package content 4
4. Unpacking 5
5. Intended use 5
6. Symbols and conventions 5
7. Instrument description 6
8. Assembling 7
8.1 Light guide assembling (CL-11.1 or CL-12) 7
8.2 Connecting the power supply 7
8.3 Connectingpolarizinglters 8
9. Use of the illuminator 9
9.1 CLD-01 9
9.2 CL-11.1 9
10. Maintenance 10
11. Troubleshooting 10
Equipment disposal 11
Page 3
1. Warning
This microscope is a scientic precision instrument designed to last for many years with a minimum of maintenance. It
is built to high optical and mechanical standards and to withstand daily use. We remind you that this manual contains
important information on safety and maintenance, and that it must therefore be made accessible to the instrument users.
We decline any responsibility deriving from incorrect instrument use uses that does not comply with this manual.
2. Safety Information
Avoiding Electrical Shock
Before plugging in the power supply, make sure that the supplying voltage of your region matches with the operation voltage
of the equipment and that the lamp switch is in o position. Users should observe all safety regulations of the region. The
equipment has acquired the CE safety label. However, users have full responsibility to use this equipment safely. Please
follow the guidelines below, and read this manual in its entirety to ensure safe operation of the unit.
Page 4
① LEDilluminator
② Powersupply+powercord
③ Allenwrench
* CL-11.1orCL-12lightguidesareoptional
③
①
②
3. Package content
Page 5
4. Unpacking
The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge of the container and lift the
top half of the container. Take some care to avoid that the optical items (objectives and eyepieces) fall out and get dam-
aged. Using both hands (one around the arm and one around the base), lift the microscope from the container and put it
on a stable desk.
Do not touch with bare hands optical surfaces such as lenses, lters or glasses. Traces of grease or other
residuals may deteriorate the nal image quality and corrode the optics surface in a short time.
5. Intended use
Standard models
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
IVD Models
Also for diagnostic use, aimed at obtaining information on the physiological or pathological situation of the subject.
6. Symbols and conventions
The following chart is an illustrated glossary of the symbols that are used in this manual.
CAUTION
This symbol indicates a potential risk and alerts you to proceed with caution.
ELECTRICAL SHOCK
This symbol indicates a risk of electrical shock.
Page 6
7. Instrument description
LIGHT GUIDE
FIXING SCREW
ON/OFF - LIGHT
INTENSITY KNOB
POWER
SUPPLY
SOCKET
Page 7
FFig. 1ig. 1
FFig. 2ig. 2
FFig. 4ig. 4
FFig. 3ig. 3
②
8. Assembling
8.1 Light guide assembling (CL-11.1 or CL-12)
1. Insert the light guide connector ① in the light exit of the
illuminator ②. (Fig. 1)
2. Lock the xing screws ③.(Fig. 2-3)
8.2 Connecting the power supply
1. Plug the power cord on the back of the illuminator. (Fig. 4)
①
③
Page 8
8.3 Installingpolarizinglters
1. Insert the polarizing lter on top of the focussing lens and
lock the xing screw. (Fig. 5-6)
FFig. 5ig. 5
FFig. 6ig. 6
2. Adjust the polarizing eect rotating each lter according to
the analyzer installed on the microscope head. (Fig. 6)
Page 9
9. Use of the illuminator
9.1 CLD-01
1. Use ON/OFF switch ① to turn the illuminator on and to adjust
the light intensity. (Fig. 7)
• Set the desired light intensity according the specimen under
examination.
FFig. 7ig. 7
FFig. 8ig. 8
FFig. 9ig. 9
①
9.2 CL-11.1
1. Bend the self-supporting arms ② to aim the light beam. (Fig.
8)
②
2. Each arm can be oriented in a separate way, in order to
achieve a proper illumination. (Fig. 9)
Page 10
10. Maintenance
11. Troubleshooting
Review the information in the table below to troubleshoot operating problems.
PROBLEM CAUSE SOLUTION
I. Optical System
LED does not light. Power cord is unplugged. Plug power cord into the power outlet.
Main switch is in “OFF” position Put the main switch to “ON”
Light too dim on the sample Intensity set too low. Adjust the intensity knob.
Device environment
This device is recommended to be used in a clean, dry and shock free environment with a temperature of 5°-40°C and a
maximum relative humidity of 85 % (non condensing). Use a dehumidier if needed.
To think about when and after using the device
• The device should always be kept vertically when moving it and be careful so that no moving parts
fall out.
• Never mishandle or impose unnecessary force on the device.
• Never attempt to service the device yourself.
• After use, turn o the light immediately, cover the whole microscope with the provided dust-cover,
and keep it in a dry and clean place.
Electrical safety precautions
• Before plugging in the power supply, make sure that the supplying voltage of your region matches
with the operation voltage of the equipment and that the lamp switch is in “OFF” position.
• Users should observe all safety regulations of the region.
• The equipment has acquired the CE safety label. However, users do have full responsibility to use
this equipment safely.
Cleaning the optics
• If the optical parts need to be cleaned try rst to: use compressed air.
• If that is not sucient: use a soft lint-free piece of cloth with water and a mild detergent.
• And as a nal option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.
• Note:ethanolandetherarehighlyammableliquids.Donotusethemnearaheatsource,nearsparksornear
electric equipment. Use these chemicals in a well ventilated room.
• Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage the optics.
Forthebestresults,usetheOPTIKAcleaningkit(seecatalogue).
If you need to send the device to Optika for maintenance, please use the original packaging.
Altri manuali per ACCESSORIES Series
5
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Optika Italy Microscopio
Optika Italy
Optika Italy B-1000 Series Manuale utente
Optika Italy
Optika Italy B-1000 Series Manuale utente
Optika Italy
Optika Italy IM-5 Series Manuale utente
Optika Italy
Optika Italy ACCESSORIES Series Manuale utente
Optika Italy
Optika Italy B-150P Series Manuale utente
Optika Italy
Optika Italy B-510 Series Manuale utente
Optika Italy
Optika Italy B-510 Series Manuale utente
Optika Italy
Optika Italy B-800 Series Manuale utente
Optika Italy
Optika Italy SLX Series Manuale utente
Optika Italy
Optika Italy IM Series Manuale utente
Optika Italy
Optika Italy SZ Series Manuale utente
Optika Italy
Optika Italy B-190TB Series Manuale utente
Optika Italy
Optika Italy B-380 Series Manuale utente
Optika Italy
Optika Italy IM-5 Series Manuale utente
Optika Italy
Optika Italy B-150P Series Manuale utente
Optika Italy
Optika Italy B-380 Series Manuale utente
Optika Italy
Optika Italy LAB Series Manuale utente
Optika Italy
Optika Italy INSPECTION SYSTEMS Series Manuale utente
Optika Italy
Optika Italy B-150 Series Manuale utente
Optika Italy
Optika Italy B-383 Series Manuale utente
