Optika Italy CL Series Manuale utente
Ver. 1.0 2020
INSTRUCTION MANUAL
CL Series
Model
CL-32
CL-33
Page 2
Summary
1. Warning 3
2. Symbols and conventions 3
3. Safety Information 3
4. Intended use 3
5. Overview 4
5.1 CL-32 4
5.2 CL-33 5
6. Unpacking 6
7. Assembling 6
7.1 CL-32 6
7.2 CL-33 7
7.3 System assembling 8
7.3.1 CL-32 8
7.3.2 CL-33 8
8. Use of the illuminator 9
8.1 Light intensity adjustment 9
8.2 Focusing the light beam 9
8.3 Charging the battery 10
9. Important safety instructions 11
10. Personal safety instructions 11
11. Maintenance 12
12. Troubleshooting 12
Equipment disposal 13
Page 3
1. Warning
This device is a scientic precision instrument designed to last for many years with a minimum of maintenance.
It is built to high optical and mechanical standards and to withstand daily use. We remind you that this manual
contains important information on safety and maintenance, and that it must therefore be made accessible to the
instrument users. We decline any responsibility deriving from incorrect instrument use uses that does not comply
with this manual.
2. Symbols and conventions
The following chart is an illustrated glossary of the symbols that are used in this manual.
CAUTION
This symbol indicates a potential risk and alerts you to proceed with caution.
ELECTRICAL SHOCK
This symbol indicates a risk of electrical shock.
3. Safety Information
Avoiding Electrical Shock
Before plugging in the power supply, make sure that the supplying voltage of your region matches with the op-
eration voltage of the equipment and that the lamp switch is in o position. Users should observe all safety reg-
ulations of the region. The equipment has acquired the CE safety label. However, users have full responsibility
to use this equipment safely. Please follow the guidelines below, and read this manual in its entirety to ensure
safe operation of the unit.
4. Intended use
Standard models
For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.
IVD Models
Also for diagnostic use, aimed at obtaining information on the physiological or pathological situation of the
subject.
Page 4
MINI USB PORT
(BACK SIDE) SELF SUPPORTING
LIGHT GUIDE
ADHESIVE
MAGNETIC
HOLDER
FOCUSABLE
LENS
ON/OFF - LIGHT
INTENSITY
ADJUSTMENT
BUTTON
5. Overview
5.1 CL-32
Page 5
5.2 CL-33
SELF SUPPORTING
LIGHT GUIDE
FOCUSABLE
LENS
MAGNETIC
HOLDER
CABLE
HOLDER
MINI USB PORT
(BACK SIDE)
ON/OFF - LIGHT
INTENSITY
ADJUSTMENT
BUTTON
Page 6
6. Unpacking
The device is housed in a plastic container. Take some care to avoid that the optical items fall out and get dam-
aged.
Do not touch with bare hands optical surfaces such as lenses, lters or glasses. Traces of grease or
other residuals may deteriorate the nal image quality and corrode the optics surface in a short time.
7. Assembling
Once opened the box, the device parts are the following:
7.1 CL-32
① Magneticlightguide
② MiniUSB-USBcable
③ Adhesivemagneticholder
④ Powersupply
③
①
②
④
Page 7
7.2 CL-33
① Magneticlightguide(2pcs)
② Magneticholder
③ Adhesivemagneticholder(2pcs)
④ MiniUSB-USBcable(2pcs)
⑤ Powersupply(2pcs)
③
⑤
①
②
④
Page 8
FFig. 1ig. 1
FFig. 2ig. 2
FFig. 3ig. 3
7.3 System assembling
7.3.1 CL-32
• A double-sided adhesive tape disc is placed at the
bottom of the magnetic holder.
1. Remove the protective foil and place the adhesive
magnetic holder at the desired location. (Fig 1)
2. Place the magnetic part of the LED illuminator on the
holder. (Fig. 2)
7.3.2 CL-33
1. Place the magnetic holder (black) at the desired
location.
2. Place the magnetic part of the LED illuminator on the
holder. (Fig. 3)
3. Alternatively: Repeat the mounting procedure for the
CL-32 by positioning the individual magnetic adhesive
holders at the desired points and then mount the LED
illuminators.
Page 9
8. Use of the illuminator
FFig. 4ig. 4
FFig. 5ig. 5
8.1 Light intensity adjustment
1. Operate on the button ① to turn ON/OFF the LED and
to increase/decrease the illumination voltage. (Fig. 4)
2. The button will turn green.
• By pressing the button the light will cyclically
change: LOW INTENSITY --> HIGH INTENSITY -->
OFF.
8.2 Focusing the light beam
• The terminal part of the illuminator is equipped with a
beam focusing system
.
• By moving up or down the terminal part ②, you can
concentrate or diuse the beam of light.
1. Move the terminal part downwards to have a more
concentrated light beam. (Fig. 6)
2. Move the terminal part upwards to have a more diuse
light beam. (Fig. 7)
①
FFig. 7ig. 7
FFig. 6ig. 6
②
Page 10
8.3 Charging the battery
1. Connect the mini USB terminal of the cable to the LED
illuminator. (Fig. 8)
2. Connect the USB terminal to the power supply and
then plug the power supply into the wall outlet
.
• A green light lights up while the battery is charging.
• If you use the LED illuminator when the USB cable
is connected, the charging light turns red.
FFig. 8ig. 8
Questo manuale è adatto per i seguenti modelli
2
Indice
Lingue:
Altri manuali Optika Italy Microscopio
Optika Italy
Optika Italy SZR Series Manuale utente
Optika Italy
Optika Italy B-510 Series Manuale utente
Optika Italy
Optika Italy B-1000 Series Manuale utente
Optika Italy
Optika Italy B-810 Series Manuale utente
Optika Italy
Optika Italy B-150P Series Manuale utente
Optika Italy
Optika Italy B-290 Series Manuale utente
Optika Italy
Optika Italy B-380 Series Manuale utente
Optika Italy
Optika Italy ACCESSORIES Series Manuale utente
Optika Italy
Optika Italy IM Series Manuale utente
Optika Italy
Optika Italy IM-3 Series Manuale utente
Optika Italy
Optika Italy B-510 Series Manuale utente
Optika Italy
Optika Italy INSPECTION SYSTEMS Series Manuale utente
Optika Italy
Optika Italy B-510 Series Manuale utente
Optika Italy
Optika Italy SZ-STL5 Manuale utente
Optika Italy
Optika Italy B-380 Series Manuale utente
Optika Italy
Optika Italy IM Series Manuale utente
Optika Italy
Optika Italy B-150P Series Manuale utente
Optika Italy
Optika Italy B-800 Series Manuale utente
Optika Italy
Optika Italy B-380 Series Manuale utente
Optika Italy
Optika Italy IM-5 Series Manuale utente
